Shakespeare Electronic Marine Instruments 409 R User Manual

Style 409-R Mounting Kit  
Thank you for purchasing a Shakespeare antenna product.  
Customer comments are welcome. Before installing, please study  
the diagram and check parts supplied against those listed.  
Retainer Bar  
Wing Nut  
Reducing Adapter  
Antenna  
Standoff Bracket  
Assembly  
IMPORTANT! Please read all instructions  
before installing.  
STANDOFF  
BRACKET  
Mounting  
Screw*  
The Style 409-R Mounting Kit is a versatile antenna  
mounting kit comprised of a Shakespeare Style 407 Heavy Duty  
4-Way Swivel Mount and a Shakespeare Style 408-R Standoff  
Bracket. The swivel mount permits mounting on almost any  
surface, vertical or horizontal, and allows antenna laydown  
in any desired direction. For use with 1½” antennas, and  
antennas of 11/8” and 1” diameter by using the appropriate  
adapter (supplied) in the standoff bracket.  
Supplied Parts  
1 Standoff Bracket assembly  
1 1” Reducing adapter  
1 11/8” Reducing adapter  
1 Swivel Mount assembly  
1 Mount base plate  
Washer*  
Lockwasher*  
Nut*  
Tools required: Drill and drill bit for ¼” screws;  
screwdriver; wrench or pliers  
3
1 /8“ Hex-head Bolt  
Installation Instructions  
3
1 /8“ Internal Tooth Lockwasher  
Choose an antenna mounting location that is as high as  
feasible, as free as possible from obstructions, and as far as  
possible from other antennas and strong sources of RF.  
3
1 /8“ Plain Washer  
3
1 /8“ Hex Nut  
1. Using the base of the Swivel Mount as a template, mark the  
location for the four mounting holes. Drill ¼” holes.  
Bulkhead Mounting: SIDE VIEW  
Mounting  
Note: When drilling fiberglass, place a wooden backup block  
behind the surface if possible, to minimize push-through  
damage.  
Lockwasher*  
Nut*  
1”-14 Thread  
Screw*  
Bolt  
2. Assemble the Swivel Mount by joining its two sections and  
securing them with the hex-head bolt, washer, lockwasher and  
nut (supplied). This joint can be in two positions, according to  
whether you’re mounting to a vertical or horizontal surface.  
3. Attach the Swivel Mount to the mounting surface using  
hardware (not supplied) that is applicable to the mounting  
surface.  
Bulkhead  
Mounting:  
Swivel  
Bolt  
FRONT  
VIEW  
IMPORTANT: If the thickness of the mounting  
surface is not adequate to support the antenna  
under expected stress, a wooden back-up pad  
(not supplied) should be applied underneath the  
mounting surface during installation.  
Mounting  
Screw*  
Mounting Hole  
4. Assemble the antenna to the Swivel Mount, being careful not  
to damage the antenna’s cabling, if any.  
Base Plate  
5. Loosen the wing nut on top of the Standoff Bracket and slide  
the retainer bar out of the way. Gently place the antenna in  
its mounting position in the U-shaped opening in the bracket.  
For 11/8” and 1” antennas, put the appropriate reducing adapter  
(supplied) in the opening.  
Nut*  
Lockwasher*  
Deck Mounting: SIDE VIEW  
* Not supplied. For some types of mounting surfaces you might need  
stainless steel woodscrews or other hardware.  
Shakespeare Electronic Products Group  
Shakespeare is a subsidiary of Jarden Corporation (NYSE: JAH)  
©2002 Shakespeare Co.  
· Form I-409-R J: rev. 04/25/2010  
 

Sharp Air Conditioner AE X09MC0J User Manual
Shure DJ Equipment microphone mixer User Manual
Snapper Chipper SG8000 User Manual
Soleus Air Air Conditioner KFH 18 User Manual
Sony Cordless Telephone spp s2430 User Manual
Sony Video Game Controller 10037 User Manual
Spin Master Baby Toy Paint Sensation User Manual
Stearns Boat B524 User Manual
SUPER MICRO Computer Computer Hardware X8DTU LN4F+ User Manual
Sylvania Car Satellite TV System C6427TF User Manual