Spin Master Baby Toy Paint Sensation User Manual

Axle  
Arm  
Cover  
Paint  
Button  
Control  
Handle  
Spinning  
Tray  
2-sided Paint  
Canisters  
Swirl  
Button  
Clear  
Dome  
Control  
Arm  
“ON/OFF”  
Switch  
Paint Containers  
Cleaning Tool  
• Design COOL ART and CRAFTS with Paint Sensation !  
• Paint on whatever you can fit into the Spinning Tray!  
Please remove everything from the packaging and compare to the contents shown on this page.  
If any items are missiont, please call Spin Master’s customer care hotline: 1-800-622-8339.  
Product and colours may vary.  
Keep these instructions for future reference as the contain important information.  
 
ASSEMBLY (CONTINUED)  
3
Cover the Paint Canister  
with the Clear Dome,  
turning it clockwise,  
Clear Dome  
until it locks into place.  
4
Place Spinning Tray into the Bottom Paint  
Tray and rotate it until it slides down and into  
place.  
Pull the Control Arm out and position the  
Bottom Paint Tray into the slot in the centre of  
the control arm, as shown.  
You are ready to Create Your Own Paint  
Sensations !  
Bottom Paint Tray  
Spinning Tray  
Control Arm  
 
Try experimenting with each of the 3 controls. Experimenting will lead you to discover how  
to make endless designs with Paint Sensation! Paint Sensationhas 3 control locations:  
CREATING  
1
Pressing or Pulsing the Paint Button  
controls how fast paint comes out  
of the Paint Canister.  
“ON/OFF” Switch  
DESIGN TIP: You will get  
different designs depending  
on how you use the Control  
Arm, Paint Button and  
Swirl Button.  
Place paper or any 3D  
object less than 1” high  
into the Spinning Tray.  
Turn Unit “ON”.  
2
3
Pressing the Swirl Button controls the  
Spinning Tray. Slowly pulse the Swirl  
Moving the Control Arm in or out lets you control  
where the paint goes onto your art.  
Button. This will move the tray a little at  
a time and will give you straight paint  
lines. Or hold the swirl button down for  
longer bigger swirls.  
 
• Remove the Arm Cover, Trays, Clear Dome and Paint Canisters from Paint Sensation.  
• Rinse or soak each one with warm water and soap.  
• Hold the Arm Cover upside down under warm running water.  
• Rinse until all parts are clean.  
CLEANING  
• Allow to dry.  
1
Each Paint Canister has tiny holes that the paint  
comes out of. If these holes get blocked you  
can’t paint. The Cleaning Tool unblocks the  
Paint Holes. To use the Cleaning Tool, insert as  
shown. Align half-moon curve on the Paint  
Canister with the docking curve in the Cleaning  
Tool.  
Half Moon Curve  
Paint Hole  
2
3
Wiggle the Paint Canister until the raised Center  
Circle on the Paint Canister lid fits snugly into  
the half circle in the Cleaning Tool base.  
Press the button on the Cleaning Tool to clean  
the hole.  
Always release button on the Cleaning Tool  
before removing Paint Canister from the  
Cleaning Tool. Repeat to clean the second  
hole in the Paint Canister.  
Raised Center Circle  
WARNING: Cleaning Tool contains a  
functional sharp point.  
Press Button  
to clean Paint Hole  
Cleaning Tool  
Half Circle  
 
TROUBLESHOOTING  
Paint is not coming out when I press the  
Paint Button.  
• The Paint Canister does not have enough paint in it. Refill with fresh paint.  
• The Paint Canister holes are blocked. Read the section on Cleaning Tool  
under Cleaning Paint Canisters in these instructions.  
Paint is dripping onto my creations.  
• Paint can build up in the Arm Cover after frequent use. Remove  
the Arm Cover and rinse with warm soapy water. Reattach to the Paint Arm.  
The paint comes out too fast.  
• Try pulsing the Paint Button  
I can’t make my designs look  
like swirls.  
• Slow down how fast you are moving the Control Arm back and forth.  
Paint SensationTM has no power.  
• Make sure the ON/OFF button is in the ON position.  
• Batteries may need replacing. Ask a parent to replace the batteries.  
I can’t get water out from inside the Arm  
Cover after it has been washed.  
• Shake out as much water as possible after cleaning. Residual water will  
evaporate and will not affect the toy’s performance.  
Cleaning Tool button will not depress.  
• The Half Moon Tool Guide has not connected with the Tool Guide inside the  
Cleaning Tool. Reposition and reinsert until the Cleaning Tool Button  
depresses.  
BATTERY INSTALLATION  
1. Use a phillips screwdriver (not provided) to loosen the battery compartment door hold down screws.  
Remove the battery compartment door.  
2. Install four 1.5-Volt “C” alkaline batteries (not included). Be careful to align the positive (+) and (-) polarities with the  
corresponding markings inside the battery compartment.  
3. Replace the battery compartment door and refasten the screws.  
4. Batteries are not included.  
Paint-Sensation  
turned over to access the  
Battery Compartment  
IMPORTANT BATTERY INFORMATION  
• Battery installation and change of battery should always be performed by an adult.  
• Be careful to install the batteries with the correct polarity as indicated.  
• Do not mix alkaline, standard (carbon zinc), rechargeable (nickel cadmium or  
nickel-metal hydrate) batteries.  
Battery  
Compartment  
Door  
• Different types of batteries or new and used batteries are not to be mixed.  
• Use Alkaline batteries for better performance.  
• Non-rechargeable batteries are not to be recharged.  
• Rechargeable batteries are to be removed from the toy before being charged  
(if removable).  
Four  
1.5-Volt  
“C”  
Batteries  
• Exhausted batteries are to be removed from the toy.  
• Only batteries of the same or equivalent type as, recommended are to be used.  
• The supply terminals are not to be short circuited.  
• Do not mix old and new batteries.  
• Products with non-replaceable batteries are not to be disposed of in a fire  
as the batteries inside may explode and leak.  
• Dispose of batteries safely.  
• Do not use rechargeable batteries.  
Battery Compartment  
CAUTION: Changes or modifications to this product not expressly approved by party responsible for compliance may  
void the user’s authority to operate the equipment. This product may stain or stick to some surfaces. Protect play area  
before use. Use damp cloth with warm water and soap to remove stains from clothing, carpeting and other surfaces that  
the item is likely to come in contact with. SAFETY TESTED. Remove all packaging material before giving the toy to your  
child. Please retain this information for future reference.  
Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 Canada  
Manufactured for and distributed by Spin Master Ltd.  
Conforms to safety standards ASTM F963-03, ASTM D-4236 & EN71,  
Regulatory Requirements. Products and colors may vary. MADE IN CHINA.  
Item #70658 US-ENG-70658-IS-5  
 

SonicWALL Security Camera es4300 User Manual
Sony Blu ray Player BX150 User Manual
Sony Universal Remote RM V201T User Manual
Spectra Logic Server NTIER700 User Manual
StarTechcom Network Router AP150WN1X1U User Manual
Sun Microsystems Computer Drive VSM GUI User Manual
Sunrise Medical Oxygen Equipment 515 SERIES User Manual
Swann DVR SW244 TDV User Manual
Tanaka Brush Cutter TBC 325 User Manual
TANDBERG Digital Camera D1404102 User Manual