Fujitsu Printer DL7400 User Manual

Quick Start Guide for FUJITSU DL7400 Printer  
3. Installing the Ribbon Cartridge.  
4. Position the left tractor. Push the left locking lever down to  
secure the tractor. Center the middle forms support.  
User’s Manual  
Paper handling  
Release the ribbon cartridge from its package and push in the  
gray ribbon release tabs on the side, and slide the roller from  
the LOCK position to the FREE position.  
Adjusting for paper thickness  
You can use the MANUAL GAP DIAL to adjust the paper  
thickness manually at manual mode.  
Refer to " Manual Gap Dial Settings " of the manual before it  
adjusts.  
The User’s Manual is provided as an Adobe® Acrobat® PDF file on  
the CD shipped with your printer. It requires Adobe Acrobat  
Reader for viewing. To view the User’s Manual, access it from the  
DL7400 User's Manual line folder on the CD and double-click on  
the file name. If you do not have Adobe Acrobat Reader, it is  
available for downloading from the Adobe web site,  
5. Adjust the left margin.  
6. Fit the paper feed holes onto the left and right tractor pins.  
Adjust the right tractor to the width of the form.  
Close the paper holders.  
Ribbon feed knob  
Turn the knob  
clockwise.  
Loading single sheets  
Roller  
1. Make sure that the printer is turned on. Press the PAPER PATH  
Unpacking the printer  
button to select CUT SHEET.  
Please confirm that the following things are enclosed  
Printer (1)  
2. Adjust the left margin.  
Push the lock lever down to secure the guide.  
Release tabs  
Black ribbon cartridge (1)  
Power cord (1)  
Setup disk (1)  
3. Pull the sub guide out as required to accommodate the paper size.  
Thread the ribbon between the print head and the print guide,  
then gently press down on the ribbon cartridge against the printer  
until it clicks into place.  
Paper Holders  
0
This guide (1)  
7. Pull the right tractor to stretch the paper taut. Push the right  
locking lever down to secure the tractor in place.  
Setting up  
Open the carton and pull the printer and its components out.  
Remove the tapes and cushions securing the printer.  
8. Lower the paper table to the down position (normal mode).  
1. Setting the paper table  
Turn the paper table (1) as shown in the table below, then  
push it (2) and set it (3).  
4. Insert a sheet of paper into the paper table.  
Make sure that the front edge of the paper engages snugly with  
the feed roller.  
5. Press the LOAD button. The paper will advance to the  
top-of-form position. The top-of-form position is the first line  
on which printing can start. To adjust the position of the paper  
slightly, press the S MICRO FEED button or the T MICRO  
FEED button.  
(1)  
(2)  
Paper table  
(3)  
9. Press the PAPER PATH button to select TRACTOR F.  
4. Connecting the interface cable  
Attach the interface cable to the connector.  
10. Press the LOAD button to load the paper to the top-of-form  
position.  
The complete setup conditions are shown below.  
Make sure that the top end of the paper table is engaged with  
the printer guide pin and the guide pin on the paper table is  
inserted into the cover groove.  
Top-of-form is the first line on which printing can start.  
After loading paper, the printer goes into online mode.  
* Rear feedPlease refer to the chapter of "Paper Handling"  
of the user's manual.  
Cover guide Solt  
Centronics parallel+ RS232C  
Cut sheet table guide pin  
Installing the printer driver  
A printer driver is required to use the printer in a Windows  
environment.  
Special printer drivers for Windows 95, 98, Me, NT 4.0, 2000, XP,  
and 2003 are provided with the DL7400 printer.  
For information on how to install printer drivers, refer to the  
Readme.txt file for the printer driver to be installed.  
· These printer drivers run with DPL24C+ emulation.  
Be sure to specify DPL24C+ emulation for the printer mode.  
· The DL7400 printer driver is a printer driver for monochrome  
printing.  
Loading Continuous Forms (Front Feed)  
1. Make sure that the printer is turned on. Remove any single-sheet  
paper from the printer.  
Centronics parallel  
+ USB  
Centronics parallel  
+ USB ( + LAN) *  
2. Lift up the paper table as shown below.  
Guide pin  
3. Release the tractor locking levers by pulling them up. Open  
the tractor paper holders. See the following figure.  
* The LAN interface is a user add-on option.  
2. Open the front cover and remove the shipping restraint  
cardboard that holds the print head carriage in place (shown  
Use the following procedure to install the DL MENU.  
5. Plug one end of the power cord into the power connector on the  
rear of the printer.  
Plug the other end of the power cord into the power outlet.  
below).  
1. Create an appropriate folder in the hard disk and copy to it all of  
the files in the DL MENU folder (DLMENU.EXE,  
DLMENU.HLP, DLMENU.CNT).  
Front cover  
Cardboard  
NOTE: A disk capacity of 500KB is required to install  
the DL MENU.  
2. Start by double clicking the DLMENU.EXE file or by specifying  
the DLMENU.EXE file from "Start" > "Run".  
Middle forms support  
Locking lever  
Locking lever  
KA02038-Y820  
 

Electro Voice DJ Equipment SB121 User Manual
Electro Voice Portable Speaker S 60 User Manual
Escient Home Theater Server FireBall Media Management system User Manual
EverFocus Security Camera EZN850 User Manual
Extron electronic Network Cables 3192M User Manual
Extron electronic Stereo Amplifier XPA2001 100V User Manual
Fisher Price Motorized Toy Car L6345 User Manual
GE Hot Beverage Maker 106764 User Manual
GE Washer Dryer WCXH208 User Manual
Gianni Industries Door LZ NH2300N User Manual