Fujitsu Laptop ST4000P User Manual

C o p y r i g h t  
Fujitsu PC Corporation has made every effort to ensure  
the accuracy and completeness of this document;  
however, because ongoing development efforts are made  
to continually improve the capabilities of our products,  
we cannot guarantee the accuracy of the contents of this  
document. We disclaim liability for errors, omissions, or  
future changes herein.  
PCMCIA and CardBus are registered trademarks of the  
Personal Computer Memory Card International  
Association.  
Intel, Pentium, and SpeedStep are registered trademarks  
of Intel Corporation.  
Wi-Fi is a trademark of the Wireless Ethernet  
Compatibility Alliance (WECA).  
Fujitsu and the Fujitsu logo are registered trademarks of  
Fujitsu Limited; Stylistic is a registered trademark of  
Fujitsu PC Corporation.  
All other products are trademarks or registered  
trademarks of their respective companies.  
Kensington and MicroSaver are registered trademarks of  
the Kensington Technology Group.  
Copyright 2002 - Fujitsu PC Corporation. All rights  
reserved. No part of this publication may be copied,  
reproduced, or translated, without the prior written  
consent of Fujitsu PC Corporation. No part of this  
publication may be stored or transmitted in any  
electronic form without the prior consent of Fujitsu PC  
Corporation  
Microsoft is a registered trademark of Microsoft  
Corporation. Windows 2000 Professional and Windows  
XP Professional are trademarks of Microsoft  
Corporation.  
FPC58-0714-02  
DECLARATION OF CONFORMITY  
according to FCC Part 15  
Responsible Party Name:  
Address:  
Fujitsu PC Corporation  
5200 Patrick Henry Drive  
Santa Clara, CA 95054  
408-982-9500  
Telephone:  
Declares that product:  
Model Series: Stylistic® ST4000P  
Complies with Part 15 of the FCC Rules  
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and, (2) This device must accept any interference  
received, including interference that may cause undesired operation.  
Note: For more detailed information about the FCC rules and their applicability to the Stylistic  
ST4000P Series pen tablet PC, refer to Chapter 5 of this document.  
 
Ta b l e o f C o n t e n t s  
Table of Contents  
Modem Connection . . . . . . . . . . . . . . . . . . . . . 25  
PC Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
PREFACE  
About This Guide. . . . . . . . . . . . . . . . . . . . . . . . . v  
Fujitsu Contact Information . . . . . . . . . . . . . . . . . v  
1
Avoiding Overheating . . . . . . . . . . . . . . . . . . . . 30  
Cleaning the Display Screen. . . . . . . . . . . . . . . . 30  
GETTING STARTED  
Status Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Tertiary Functions of Application  
SPECIFICATIONS  
and Navigation Buttons. . . . . . . . . . . . . . . . . 13  
2
Regulatory Information  
Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Charging the Battery . . . . . . . . . . . . . . . . . . . . . 23  
Removing and Installing the Battery. . . . . . . . . . 24  
Tips for Conserving Battery Power . . . . . . . . . . . 24  
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . 55  
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Index  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
i
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
ii  
 
Preface  
iii  
 
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
P r e f a c e  
iv  
 
P r e f a c e  
FUJITSU CONTACT INFORMATION  
Service and Support  
You can contact Fujitsu Service and Support in the  
Preface  
following ways:  
ABOUT THIS GUIDE  
The Stylistic ST4000P Series pen tablet PC is a high-  
performance, pen-based computer that has been  
designed to support Microsoft Windows 2000  
Professional or Windows XP Professional.  
Toll free: 1-800-8Fujitsu (1-800-838-5487)  
Fax: 1-901-259-5700  
This manual explains how to operate your Fujitsu  
Stylistic ST4000P Series pen tablet PC’s hardware and  
built-in system software.  
Before you place the call, you should have the  
following information ready so that the customer  
support representative can provide you with the  
fastest possible solution:  
The Stylistic ST4000P Series pen tablet PC is a completely  
self-contained unit with an active-matrix (TFT) color  
LCD display and a passive Touch Panel. It has a powerful  
interface that enables it to support a variety of optional  
features.  
Product name  
Product configuration number  
Product serial number  
Purchase date  
Conditions under which the problem occurred  
Any error messages that have occurred  
Hardware configuration  
Conventions Used in the Guide  
Keyboard keys appear in brackets.  
Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].  
Type of device connected, if any  
Pages with additional information about a specific topic  
are cross-referenced within the text.  
Example: (See page xx.)  
Fujitsu Online  
You can go directly to the online Fujitsu product catalog  
for your pen tablet PC by going to the Fujitsu web site at:  
On screen buttons or menu items appear in bold  
Example: Click OK to restart your pen tablet PC.  
DOS commands you enter appear in Courier type.  
P O I N T  
Example: Shut down the computer?  
You must have an active internet connection to use the  
online URL links.  
P O I N T  
The point icon highlights information that will enhance  
your understanding of the subject material.  
WARRANTY INFORMATION  
Your Stylistic ST4000P Series pen tablet PC is backed by  
either a standard one year International Limited  
Warranty. A three-year International Limited Warranty is  
available as an option. Check the service kit that came  
with your system for warranty terms and conditions.  
C A U T I O N  
The caution icon highlights information that is  
important to the safe operation of your computer, or to  
the integrity of your files. Please read all caution  
information carefully.  
W A R N I N G  
The warning icon highlights information that can be  
hazardous to either you, your Stylistic ST4000P Series  
pen tablet PC or your files. Please read all warning  
information carefully.  
v
 
                   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
P r e f a c e  
vi  
 
1
Getting Started with  
Your Pen Tablet PC  
vii  
 
     
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
viii  
 
G e t t i n g S t a r t e d  
Getting Started with Your Stylistic Pen Tablet PC  
Figure 1-1 Stylistic ST4000P Series Pen Tablet PC  
The Stylistic ST4000P Series pen tablet PC is a high-  
performance, pen-based computer that has been  
designed to support Microsoft Windows 2000 Profes-  
sional or Windows XP Professional. This chapter  
provides an overview of the Stylistic ST4000P Series pen  
tablet PC and its features.  
IN-BOX ITEMS FOR THE STYLISTIC ST4000P  
SERIES PEN TABLET PC  
Verify that the following items are included in the box  
with your pen tablet PC:  
Stylistic ST4000P Series battery  
Power cord  
AC adapter  
Screen protectors (quantity: 2)  
Stylistic ST4000P Series pen  
Pen tips (quantity: 5)  
Pen tether  
1
 
         
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
OPTIONAL ACCESSORIES  
The following optional accessories* can be used with the Stylistic ST4000P Series pen tablet PC. Refer to the  
instructions provided with these accessories for details on their use.  
Peripheral/Accessory  
Fujitsu Part Number  
Docking Options  
Stylistic ST4000 Series Tablet Dock, with CD-ROM drive  
FPCPR33AP  
Stylistic ST4000 Series Tablet Dock, with Combo DVD/CD-RW drive FPCPR32AP  
Carrying Cases  
Stylistic ST4000 Series executive leather portfolio case  
Stylistic ST4000 Series ballistic nylon portfolio case  
Stylistic ST4000 Series Bump Case  
Harsh Environment Case  
Storage Options  
FPCCC25  
FPCCC26  
FPCCC24  
FPCCC27  
External USB floppy disk drive  
Memory  
FPCFDD12  
256MB SO DIMM, 133MHz  
512MB SO DIMM, 133MHz  
128MB Compact Flash Card  
256MB Compact Flash Card  
Compact Flash Card Adapter  
Power Options  
FPCEM43  
FPCEM44  
FPCEM02  
FPCEM03  
FPCFA01  
AC adapter with US cord  
Main Battery  
FPCAC23  
FPCBP63AP  
FPCAA02  
FPCBC06  
Auto/Airline Adapter  
Battery Charger  
Additional Accessories  
Infrared keyboard  
FPCKB41A1P  
FMWKB5A  
FPCMO07  
FPCPN08AP  
FPCSP03AP  
FMWST2  
USB keyboard  
Infrared Mouse  
Stylistic ST4000P Series pen (5-pack)  
Screen Protectors (12-pack)  
Pen tether  
* For the latest list of accessories available for your Stylistic ST4000P Pen Tablet PC, be sure to frequently  
Table 1-1 Stylistic ST4000P Optional Accessories  
2
 
                 
G e t t i n g S t a r t e d  
STYLISTIC PEN TABLET PC FEATURES  
Features and controls that you use to operate the Stylistic ST4000P Series pen tablet PC are outlined below and illus-  
trated in Figures 1-1 through 1-5. Details on using these features and controls are provided later in this manual.  
Power On/Suspend/  
Resume Button  
Built-in Microphone  
System  
Status  
LEDs  
Application  
Buttons  
User-Programmable  
Application Buttons  
Speaker  
Infrared  
Keyboard/  
Mouse Port  
Navigation  
Buttons  
Figure 1-2 Stylistic ST4000P Series Pen Tablet PC Features (Front View)  
Application buttons: Allow you to quickly launch  
pre-defined applications and utilities by pressing a  
button.  
Front Features:  
1
System status LEDs: Indicate the operational status of  
the pen tablet PC and hard disk drive, the charge level  
of the battery, and the status of the hovering mode.  
Navigation buttons: The navigation buttons allow  
you to move: Page Up/Page Down, Tab Right/Tab  
Left, Cursor Up/Cursor Down, and Cursor Right/  
Cursor Left.  
Power On/Off/Suspend/Resume button: Allows you  
to turn on, off, suspend, resume, hibernate or wake  
the pen tablet PC’s operation in order to optimize  
battery life.  
Speaker: Allows you to listen to mono audio files.  
Infrared keyboard/mouse port: The infrared port  
wraps around the front and bottom of the display,  
and is used for communicating with a proprietary  
infrared keyboard or mouse.†  
Built-in Microphone: The built-in microphone allows  
you to input mono audio.  
These peripherals and accessories are sold separately.  
3
 
                   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
Thermal  
Suede  
Tablet Dock  
Latch Point  
Wireless  
LAN On/Off  
Switch*  
System  
Interface  
Connector  
Wireless LAN  
and/or Modem  
Module Cover*  
Latch Point  
Wireless  
LAN  
Antenna*  
(inside case)  
Memory  
Module  
Cover  
Tablet Dock  
Latch Point  
Hard Disk  
Drive Cover  
Battery  
Release  
Latch  
Battery  
Pack  
Figure 1-3 Stylistic ST4000P Series Pen Tablet PC Features (Back View)  
* The system is configured with one of two modules: a standard modem module or an optional wireless LAN/modem  
combo module.  
covered with “thermal suede. This material should  
Back Features:  
1
not be removed. It is designed to minimize the  
temperature of the system for the user when a  
running system is carried for a period of time.  
System interface connector: Allows you to connect  
the optional Stylistic Tablet Dock.  
Removable battery: Can be removed and replaced  
Wireless LAN module cover: Provides protection for  
with a charged battery.  
the optional wireless LAN radio solution.  
Battery release latch: Used to release the removable  
battery.  
Wireless LAN On/Off switch: For systems with a  
wireless device installed, this switch turns the device  
on and off. You should switch the device off when it  
is not in use in order to maximize battery life.  
Tablet Dock latch point: Allows you to attach the  
system to an optional Tablet Dock.  
Hard disk drive cover: Covers the hard disk drive  
module.  
Memory module cover: Removable cover over the  
memory modules.  
These peripherals and accessories are sold separately.  
Thermal Suede: Several areas of the system back are  
4
 
                   
G e t t i n g S t a r t e d  
Microphone  
Jack  
IEEE 1394 Jack  
IrDA Port  
Pen Holder  
Air flow vents  
Headphone  
Jack  
Pen Tether  
Attachment  
PC Card Slot  
PC Card  
Eject Button  
USB Ports  
Point  
Figure 1-4 Stylistic ST4000P Series Pen Tablet PC Features (Top View)  
USB ports: Allow you to connect Universal Serial  
Bus-compliant devices (compliant with USB  
Standard Revision 1.1) to the pen tablet PC.  
Additional USB ports are located on the optional  
Tablet Dock.  
Top Features:  
1
Pen: The main input device that you use to execute  
programs and enter data. A pen holder is built into  
the pen tablet PC to store the pen when not in use.  
Microphone Jack: Allows you to connect an external  
microphone.  
IEEE 1394 Jack: Allows you to connect between your  
pen tablet PC and peripherals such as a digital video  
camera.  
Headphone Jack: Allows you to connect a set of stereo  
headphones.  
Air flow vents: Provides secondary cooling for  
processor. (Do not obstruct the vents.)  
PC Card slot: Allows you to install PC Cards in the  
system.  
These peripherals and accessories are sold separately.  
IrDA/FIR port: Provides an infrared interface for  
communication with devices compliant with IrDA  
Standard Revision 1.1.  
5
 
                 
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
DC Input Jack  
External Monitor Connector  
(behind door)  
Modem Jack*  
Air Flow Vents  
LAN Jack*  
KensingtonLock Slot  
Latch Point  
Figure 1-5 Stylistic ST4000P Series Pen Tablet PC Features (Left Side View)  
* The system is configured with one of two modules: a standard modem module or an optional wireless LAN/modem  
combo module. The mini-PCI expansion slot into which these modules are plugged (located under the cover) can be  
used to accommodate other mini-PCI devices.  
DC input connector: Allows you to connect the AC  
Left-Side Features:  
1
adapter or auto adapter.  
Modem jack: Allows you to connect a standard RJ-11  
connector to the pen tablet PC’s internal 56 Kbps  
modem. Note that the internal 56 Kbps LAN/modem  
module installed in the Stylistic ST4000P Series pen  
tablet PC has actual maximum transfer rates of 53  
Kbps (receive), 33.6 Kbps (send), and 14.4 Kbps  
(fax). Download rates are limited to 53 Kbps in the  
United States due to FCC restrictions.  
Air flow vents: Provides secondary cooling for  
processor. (Do not obstruct the vents.)  
Kensington™ lock slot: Allows you to attach a  
Kensington MicroSaverTM-compatible security  
cable.  
External Monitor Connector: The External Monitor  
connector allows you to connect an external CRT  
monitor.  
LAN jack: Allows you to connect a standard RJ-45  
connector to the pen tablet PC’s internal local area  
network (LAN).  
These peripherals and accessories are sold separately.  
6
 
             
G e t t i n g S t a r t e d  
Infrared Keyboard/Mouse Port  
Air Flow Vents  
Latch Point  
Pen / Pen Holder  
Figure 1-6 Stylistic ST4000P Series Pen Tablet PC Features (Right Side View)  
Infrared keyboard/mouse port: The infrared port  
wraps around the front and bottom of the display,  
and is used for communicating with a proprietary  
infrared keyboard or mouse.†  
Right-Side Features:  
1
Pen: The main pointing device that you use to execute  
programs and enter data. A pen holder is built into  
the pen tablet PC to store the pen when not in use.  
Tablet Dock latch point: Allows you to attach the  
Air flow vents: Provides secondary cooling for  
processor. (Do not obstruct the vents.)  
system to an optional Tablet Dock.  
These peripherals and accessories are sold separately.  
7
 
         
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
STATUS DISPLAY  
Icons appear in the Status display indicating the status of  
system functions such as system power and battery  
charge level. The location of icons in the Status display is  
shown in Figure 1-7.  
Power  
Charge/DC In  
Table 1-2 explains how individual icons are displayed,  
and describes what the variations of that display indi-  
cate. (If an icon is not displayed, it indicates that the  
related system function is off or inactive.  
Battery  
HDD Access  
Hovering Mode  
Figure 1-7  
Status Display Icons  
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the  
rate of one second on, five seconds off.  
Icon  
Mode/State  
LED State  
Remarks  
Power  
• On State  
Green, continuous  
The system is powered on and ready for use.  
• Idle Mode  
• Suspend-to-RAM  
Green, blinking  
Off  
The system has suspended and saved active  
settings to RAM.  
• Off State  
The system has suspended and saved settings  
and data to the hard disk drive.  
• Hibernate  
(Save-to-Disk)  
Charge/  
DC In  
• On State  
Amber  
Green  
AC adapter and battery are available and system  
is charging.  
• Idle Mode  
• AC adapter and battery are available and  
system is not charging (battery fully  
charged).  
• Suspend-to-RAM  
• Hibernate  
(Save-to-Disk)  
• AC adapter is available but battery is not  
present.  
• Off State  
Amber, blinking  
Off  
AC adapter and battery are available and waiting  
to charge (battery is out of thermal range).  
AC adapter is not available.  
8
 
         
G e t t i n g S t a r t e d  
In the following table, a “blinking” LED flashes at the rate of once per second; an LED that is “blinking, slow” flashes at the  
rate of one second on, five seconds off.  
Icon  
Mode/State  
LED State  
Remarks  
• On State  
Green, continuous  
Amber, continuous  
Red, continuous  
Red, blinking  
Battery charge is between 50%-100%  
Battery charge is between 13%-49%  
Battery charge is between 0%-12%  
There is a battery error.  
Battery  
• Idle Mode  
• Suspend-to-RAM,  
without AC adapter  
Green, blinking slow  
Amber, blinking slow  
Red, blinking slow  
Off  
Battery charge is between 50%-100%.  
Battery charge is between 13%-49%.  
Battery charge is between 0%-12%.  
• Suspend-to-RAM  
with AC adapter  
• Hibernate  
(Save-to-Disk),  
with AC adapter  
Battery is not installed, or system is off or in  
Hibernate mode.  
• Off State  
• Hibernate  
(Save-to-Disk),  
without AC adapter  
If battery is inserted during power off, LED blinks  
amber for 4 seconds to detect battery. Battery  
status is displayed for 5 seconds after that.  
• On State (or  
flashing)  
Green  
Off  
Displayed when hard disk drive is accessed.  
HDD  
Access  
• Idle Mode  
• Suspend-to-RAM  
Hard disk drive is not being accessed.  
• Hibernate  
(Save-to-Disk)  
• Off State  
• Hovering mode  
Green  
Off  
Hovering mode is active.  
Hovering  
Mode  
• Non-hovering  
mode  
Hovering mode is not active.  
Table 1-2 System Status Indicators  
9
 
       
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
APPLICATION BUTTONS  
The six application buttons are located on the upper  
right-hand side of a vertically-oriented system. (See  
figure 1-2 on page 3 for location). Three of the buttons  
have secondary functions. The secondary functions are  
activated by pressing the Function (Fn) button while  
pressing the application button.  
information about the tertiary functions, refer to  
Table 1-5 on page 13.  
P O I N T  
Ctl-Alt-Del is the only Application button that can be  
used while the system is logging on or when the system  
is locked (i.e., when you have the Logon or Computer  
Locked window showing on your desktop).  
The buttons also have separate tertiary functions that  
can be used while the system is booting up. For more  
Tablet Icon  
Button Icon  
and Name  
(Fn +  
Button)  
Description  
(Primary)  
(Secondary)  
The Ctl-Alt-Del button performs two functions:  
• Pressing the Ctl-Alt-Del button for up to one second allows you to log on  
after boot, after locking the workstation, or after resuming from power  
management  
Ctl-Alt-Del  
Button  
• After log-on, pressing the Ctl-Alt-Del button for up to one second launches  
the Windows Task Manager.  
When you press the Right-click button, your pen switches its function from left  
mouse button to right mouse button emulation. To generate a right mouse button  
click, tap on the application button once and then tap on the display.  
When you press the Fn + Right-click buttons at the same time, they provide a  
Hovering function. Hovering mode provides you with better cursor control. When  
hovering is enabled, the cursor can be positioned over an area of the screen  
without activating it. This is useful when you are attempting to read pop-up text  
associated with an icon, simulating mouse rollover, selecting a small icon, or  
beginning a paint session. Note that when Hovering Mode is active, the Hovering  
Mode Status Display LED is lit (see Table 1-2). Pressing the Fn + Right-click  
buttons at the same time again exits the Hovering function  
Hovering  
Mode  
Right-Click  
Button  
When you press the Orientation button, the system screen orientation changes  
from portrait (vertical) to landscape (horizontal) or from landscape to portrait.  
When you would like to use the tablet as an eBook, for example, you would use  
the portrait orientation, when accessing spreadsheets, you would more typically  
use a landscape orientation.  
Orientation  
Button  
The Escape application button acts the same way as an Escape key on a keyboard.  
When you press the Fn + Esc buttons at the same time*, they act to invoke a pre-  
determined application or generate a combination keystroke, as assigned the  
Tablet Button Settings utility. (You can change the settings in Control Panel ->  
Tablet Button Settings).  
Escape  
Button  
Application  
A Button  
By default, pressing the Fn + Esc combination acts the same as if you had pressed  
Ctl + Esc on a keyboard: the Start menu is launched.  
10  
 
               
G e t t i n g S t a r t e d  
Tablet Icon  
(Fn +  
Button)  
Button Icon  
and Name  
Description  
(Primary)  
(Secondary)  
The Enter application button acts the same way as an Enter key on a keyboard.  
Pressing the Fn + Ent buttons at the same time*, acts to invoke a pre-determined  
application or keystroke combination, as assigned the Tablet Button Settings utility.  
(You can change the settings in Control Panel -> Tablet Button Settings).  
Enter  
Button  
Application  
B Button  
By default, pressing the Fn + Ent combination acts the same as if you had pressed  
Alt on a keyboard: it selects a main menu in the typical Windows application.  
The Function button works in conjunction with the other application buttons to  
provide additional functionality for the buttons. Refer to specific details above.*  
Pressing the Fn button twice in succession (within the “sticky” time*), causes the  
Fujitsu menu to appear on your screen, allowing you to modify certain system  
settings.  
Function  
Button  
Table 1-3 Application Buttons - Primary and Secondary Functions  
* The Fn button has a handy “sticky” feature that allows you to press the two buttons in immediate succession, rather  
than at exactly the same time. After pressing the Fn button, you have a short time (two or three seconds) to press the  
second button. Note that this feature is not available with the Right-Click/Hovering button.  
11  
 
     
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
NAVIGATION BUTTONS  
The two navigation buttons are located on the lower  
right-hand side of a vertically-oriented system. (See  
figure 1-2 on page 3 for location). Each of the buttons can  
be toggled by pressing either end of the button.  
information about the tertiary functions, refer to  
Table 1-5 on page 13.  
P O I N T  
Ctl-Alt-Del is the only Application button that can be  
used while the system is logging on or when the system  
is locked (i.e., when you have the Logon or Computer  
Locked window showing on your desktop).  
The buttons have dual functions. The secondary func-  
tions are activated by pressing the Function (Fn) button  
while pressing the application button*.  
The buttons also have separate tertiary functions that  
can be used while the system is booting up. For more  
Buttons/icons  
Purpose (when pressed alone)  
(“Primary” function)  
Purpose (when pressed with Fn button)  
(“Secondary” function)  
This button consists of Up and Down  
segments. When the Up portion is  
pressed, you will scroll up one page.  
When pressed with the Function (Fn) button*, the  
Up portion of this button allows you to tab right.  
When pressed with the Function (Fn) button*, the  
Down portion of this button allows you to tab left.  
When the Down portion is pressed, you  
will scroll down one page.  
This button consists of Up and Down  
segments. When the Up portion is  
pressed, the cursor will move up.  
When pressed with the Function (Fn) button*, the  
Up portion of this button will move the cursor to the  
right.  
When the Down portion is pressed, the  
cursor will move down.  
When pressed with the Function (Fn) button*, the  
Down portion of this button will move the cursor to  
the left.  
* The Fn button has a handy “sticky” feature that allows you to press the two buttons in immediate succession,  
rather than at exactly the same time. After pressing the Fn button, you have a short time (two or three seconds) to  
press the second button. Note that this feature is not available with the Right-Click/Hovering button.  
Table 1-4 Navigation Buttons  
12  
 
   
G e t t i n g S t a r t e d  
TERTIARY FUNCTIONS OF APPLICATION AND NAVIGATION BUTTONS  
While you are booting up your system, the Application  
Buttons and Navigation buttons can be used for entering  
and navigating through the Basic Input-Output System  
(BIOS), and for invoking the Advanced Options Menu,  
where you can enter different modes (such as Safe  
Mode).  
operating system from disk. Information from the BIOS  
is transferred to the operating system to provide it with  
information on the configuration and status of the hard-  
ware.  
The system is booting up while the Fujitsu logo is  
displayed immediately after turning on the system. The  
table below indicates how the buttons act while the  
system is booting up and while you are in the BIOS.  
The BIOS is a program and a set of parameters that are  
stored in ROM which tests and operates your pen tablet  
PC from when you turn it on until it loads your installed  
Buttons/icons  
Purpose (when pressed while the system is booting up)  
Pressing the Ctl-Alt-Del button while the system is booting up takes you into the BIOS setup utility.  
This is the same as if you had tapped [F2] on a keyboard.  
Ctl-Alt-Del  
Button  
Pressing the Right-Click button while the system is booting up opens the Boot Options menu. This is  
the same as if you had tapped [F12] on a keyboard.  
Right-Click  
Button  
Pressing the Orientation button while the BIOS setup screen is open causes the selected item (if  
applicable) to change to the next item. Pressing this is the same as tapping the spacebar on a  
keyboard.  
Orientation  
Button  
Pressing the Esc button while the BIOS is open acts to escape from the BIOS. This is the same as if  
you had tapped [Esc] on a keyboard.  
Escape Button  
Enter Button  
Pressing the Ent button while the BIOS is open acts the same as the [Ent] button on a keyboard.  
Pressing the Fn button while the system is is displaying the operating system boot menu opens the  
Advanced Operating System Options menu. This menu allows you to enter different operating  
system modes (such as Safe Mode). Pressing this button is the same as if you had tapped [F8] on a  
keyboard.  
Function Button  
Pressing the top half of the upper navigation button while the BIOS setup screen is open causes the  
cursor in the BIOS setup screen to move up. This is the same as if you had tapped Arrow Up on a  
keyboard. This feature is also functional in the operating system boot menu.  
Pressing the bottom half of the upper navigation button while the BIOS setup screen is open causes  
the cursor in the BIOS setup screen to move down. This is the same as if you had tapped Arrow Down  
on a keyboard. This feature is also functional in the operating system boot menu.  
Pressing the top half of the lower navigation button while the BIOS setup screen is open causes the  
cursor in the BIOS setup screen to move right. This is the same as if you had tapped Arrow Right on a  
keyboard.  
Pressing the bottom half of the lower navigation button while the BIOS setup screen is open causes  
the cursor in the BIOS setup screen to move left. This is the same as if you had tapped Arrow Left on  
a keyboard.  
Table 1-5 Tertiary Functions of Application and Navigation Buttons  
13  
 
         
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
CONNECTORS AND PERIPHERAL INTERFACES  
Connectors and peripheral interfaces on the Stylistic  
ST4000P Series pen tablet PC allow connection of a  
variety of devices. Specific locations are illustrated in  
Figures 1-2 through 1-5.  
Table 1-6 provides a description of each peripheral  
connector on the Stylistic ST4000P Series pen tablet PC.  
Each of the illustrated icons is either molded into or  
printed on the pen tablet PC case.  
Connector/  
Peripheral  
Pen Tablet  
PC Icon  
Purpose  
DC in  
connector  
Connect an external power source such as the AC adapter or auto/  
airline adapter.  
USB Port  
Connect Universal Serial Bus 1.1 compliant devices to the pen tablet PC.  
PCMCIA  
Card slot  
Install a Type I or Type II PC Card.  
Microphone  
jack  
Connect an external microphone. The internal microphone is disabled  
when you plug in an external microphone.  
Headphone  
jack  
Connect stereo headphones or powered external speakers. The internal  
speaker is disabled when you plug in external headphones or powered  
speakers.  
IrDA/FIR port  
An infrared transceiver built into the pen tablet PC allows you to  
communicate with other devices that are compliant with the IrDA  
Standard Rev. 1.1. Effective range for infrared communication is about  
3 feet, and within 15 degrees off center. A clear line-of-sight path must  
exist between the IrDA port on the pen tablet PC and the IrDA  
transceiver on the other device.  
Modem  
Connect a telephone line to the optional internal modem using a  
standard RJ-11 telephone plug.  
Tablet Dock  
port  
Connect the Stylistic ST4000P Series dock or other approved docking  
device. Refer to documentation accompanying the docking device for  
more information.  
Infrared  
keyboard/  
mouse port  
An infrared receiver built into the pen tablet PC allows you to  
communicate with a wireless infrared keyboard or mouse. The keyboard  
infrared port works optimally between 10 to 30 cm (approximately 4 in.  
to 12 in.) from the keyboard infrared port, located on the bottom edge  
of the pen tablet PC. Ensure that there is a clear line-of-sight path  
between the infrared receiver on the pen tablet PC and the infrared  
transmitter on the keyboard or mouse.  
TM  
TM  
Kensington  
The Kensington Microsaver security slot allows you to secure the pen  
Lock slot  
tablet PC using Kensington-compatible locking devices.  
14  
 
                         
G e t t i n g S t a r t e d  
Connector/  
Peripheral  
Pen Tablet  
PC Icon  
Purpose  
IEEE 1394 jack  
The IEEE 1394 jack allows you to connect between your pen tablet PC  
and peripherals such as a digital video camera.  
Suspend/  
Resume button  
The Suspend/Resume/Power On button allows you to suspend pen  
tablet PC activity without powering off, resume your pen tablet PC  
from suspend mode, and power on the system when it has been shut  
down from Windows.  
Page Up/  
Page Down  
The Page Up/Page Down button allows you to navigate quickly from  
page to page without scrolling.  
Local Area  
Network (LAN)  
The LAN (RJ-45) jack is used to connect the internal Fast Ethernet (10/  
100 Base-T/Tx) to a Local Area Network (LAN) in your office or home, or  
broadband devices such as a cable modem, DSL, or satellite internet.  
Battery Release  
Latch  
The battery release latch allows you to remove the battery from your  
system for storage or replacement.  
Wireless LAN  
On-Off Switch  
The wireless LAN switch allows you to turn power to the optional  
wireless LAN device on and off.  
Table 1-6 Peripheral Connectors/Interfaces  
15  
 
             
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n O n e  
16  
 
2
Using Your  
Stylistic ST4000P  
Series Pen Tablet PC  
17  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T w o  
18  
 
U s i n g Yo u r S t y l i s t i c S T 4 0 0 0 P  
Using the Stylistic ST4000P Series Pen Tablet PC  
This chapter covers the fundamental concepts, basic  
system operation and use, and system functions of the  
Stylistic ST4000P Series pen tablet PC. You should famil-  
iarize yourself with this information before you attempt  
to operate the system.  
Operation” section later in this chapter for  
information on returning the system to the On state.  
Hibernate mode (Save-to-Disk) (S4): System  
operation is suspended. All system functions are  
turned off to conserve power. Active data in programs  
that were running before suspending system  
operation is stored on the hard disk drive. The system  
does not respond to the pen or other input. Refer to  
the “Resuming System Operation” section later in this  
chapter for information on returning the system to  
the On state.  
P O I N T  
Prior to using your system, be sure to fully charge the  
battery if you plan to run on battery power. Failure to  
do so may result in erratic performance.  
SYSTEM STATES  
Off state: All system functions are turned off to  
conserve power. The system does not respond to the  
pen or other input. The system boots at the next  
system power-on.  
Before you begin using the Stylistic ST4000P Series pen  
tablet PC, review the different system states (or modes)  
that the system can use. Being familiar with these states  
will help you determine whether it is appropriate to turn  
on, resume, suspend, hibernate or shut down the system  
when you begin or end a session. System behavior for  
each system state is described briefly in the following,  
with each system state listed in decreasing order of power  
usage:  
P O I N T  
The system consumes the same amount of power  
whether it is in Hibernate (Save-to-Disk) mode or the  
Off state.  
On state: The system is running and the display  
screen is on.  
Your system may be configured to enter some of these  
states automatically after a period of inactivity to  
conserve battery power.  
Idle state: Some system functions are regulated or  
turned off to conserve power. The display screen may  
be turned off. The system returns to the On state  
when pen activity or other input is detected.  
When you use the Stylistic ST4000P Series pen tablet PC,  
you can change the current system state in a number of  
ways, depending on the system’s current state. To deter-  
mine the current system state, observe the Power icon in  
the Status display. Table 2-1 on page 20 gives the different  
system states represented by the Power icon and describes  
how you can change the system state from the current  
state.  
Suspend-to-RAM mode (S3): System operation is  
suspended. Most system functions are turned off to  
conserve power. Power to memory is on, maintaining  
data in programs that were running before system  
operation was suspended. The system does not  
respond to the pen or other input when in Suspend-  
to-RAM mode. Refer to the “Resuming System  
19  
 
                   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T w o  
*
Icon Appearance  
Current State  
To Change State  
On State  
or  
To enter the Off state, shut down the system using the Start menu on your  
system.  
Power icon  
displayed  
continuously  
Idle State  
To enter Suspend-to-RAM or Hibernate (Save-to-Disk) state, suspend system  
operation using either a hardware or software suspend.  
Power icon blinking  
Suspend-to-  
To enter the On state, resume system operation by pressing the Suspend/  
Resume button.  
RAM  
To enter the Off state, resume system by pressing the Suspend/Resume  
button, then shut down your system.  
Power icon not  
displayed  
Off State, or,  
Hibernate  
To enter the On state, start your system, or resume system operation by  
pressing the Suspend/Resume button.  
†)  
(Save-to-Disk  
Table 2-1 Changing System States  
* Information in Table 2-1 on page 20 is supplied to help you understand which system states your system can enter from  
the current system state. Refer to the procedures on starting the system, shutting down the system, suspending system  
operation, and resuming system operation given later in this chapter.  
Your system may be configured to use either Suspend-to-RAM mode or Hibernate mode.  
POWERING UP THE PEN TABLET PC  
SHUTTING DOWN THE SYSTEM  
Follow these steps to shut down and turn off your  
system:  
Follow the procedure below to start the Stylistic  
ST4000P Series pen tablet PC. Before you begin, confirm  
that the system is in the Off state. To do so, observe the  
Status display. If the Power icon is not visible in the  
Status display, the system is in Off state or in Hibernate  
(Save-to-Disk) mode and it is safe to perform this proce-  
dure. If the Power icon is visible (either blinking or on  
continuously), do not perform this procedure. See  
“System States” earlier in this chapter for details on  
modes represented by the Power icon.  
1. If system operation has been suspended, resume  
system operation. See “Resuming System Opera-  
tion” later in this chapter for details.  
2. Save your work and close all running programs.  
3. Choose Shut Down from the Windows (2000 Profes-  
sional or XP Professional) Start menu.  
4. Carry out the Shut Down command.  
The system is now in the Off state.  
1. Ensure that the battery in your pen tablet PC is  
sufficiently charged, or connect an external power  
source such as the AC adapter or auto adapter to  
your pen tablet PC.  
SUSPENDING SYSTEM OPERATION  
The pen tablet PC allows you to suspend the system  
operation without closing programs or exiting the oper-  
ating system. Use this feature to conserve battery power  
when a system shutdown is not practical or when the  
battery needs to be changed.  
2. Press the Power On/Suspend/Resume button to start  
the system.  
After performing initialization, the system starts the  
operating system installed on the hard disk drive. Once  
the operating system is running, you can use the system.  
P O I N T  
If you have set your system to turn power off from the  
Power Options utility in the Control Panel, the  
following procedure will not be possible, since pressing  
the button shuts the system down rather than  
suspending it. To change your power options, go to  
Start -> Settings -> Control Panel -> Power Options.  
20  
 
                 
U s i n g Yo u r S t y l i s t i c S T 4 0 0 0 P  
To suspend system operation:  
data, wait until system operation has suspended  
before you remove the battery. Note that after you  
remove the battery, you have approximately five  
minutes to replace it with a new battery or to plug in a  
power supply before the bridge battery is depleted.  
1. Press the Suspend/Resume button, or carry out the  
Standby command from your operating system or  
power management program. (If your system is  
configured to suspend operation using Hibernate  
mode, which is explained later in this procedure, a  
message is displayed while data is saved to your hard  
disk.)  
Your system may be configured to suspend operation  
automatically after a period of inactivity.  
Your system may be configured to enter Hibernate  
mode automatically after a period of time in Suspend-  
to-RAM mode.  
C A U T I O N  
If you are replacing the battery, wait until system  
operation is suspended and the power icon is flashing  
before you remove the battery. Failure to do so could  
result in loss of your unsaved data. (Note that if the  
Resume On LAN function is enabled in the BIOS setup,  
you should not remove the battery unless the system is  
shut down. When Resume ON LAN is enabled, the  
bridge battery is disabled in order to optimize battery  
life.)  
The system uses a small amount of battery power  
when in Suspend-to-RAM mode. Eventually, the  
battery will become fully discharged.  
P O I N T  
If you will not be using the system for an extended  
period of time, shut down the system rather than using  
Suspend-to-RAM mode.  
2. The Power icon either flashes (Suspend-to-RAM) or  
is not displayed (Hibernate) when system operation  
is suspended, depending on how your system is  
configured. At this point, programs that were  
running are stopped, active data is saved, and the  
system enters one of two different low-power states,  
or suspend modes, as explained in the following  
paragraphs.  
If the battery charge drops to a Low-Battery Warning  
level while the system is running, the system will beep  
periodically. If this occurs, suspend system operation,  
shut down the system, or attach an external power  
source, such as the AC adapter, to the pen tablet PC.  
If the battery charge drops to a Critically Low level  
while the system is running, the system is forced into  
a pre-selected mode (Suspend-to-RAM or  
3. Observe the Power icon in the Status display to deter-  
mine which suspend mode your system is using.  
Hibernate). If this occurs, you must either install a  
charged battery, or connect an appropriate external  
power source such as the AC adapter before you can  
resume system operation. (If the battery charge drops  
to a Critically Low level while the system is in  
Suspend-to-RAM mode, the system stays in Suspend-  
to-RAM mode until power is restored or totally  
dissipated.)  
Power icon is blinking: Suspend-to-RAM mode.  
In this mode, active data is saved by maintaining  
power to RAM while most other system components  
are powered off. The Battery Gauge icon in the Status  
display indicates the battery charge level.  
Power icon is not displayed: Hibernate mode.  
Suspending system operation interrupts data  
communications; therefore, some programs may  
block the system from suspending to prevent an  
interruption.  
In this mode, active data is stored on the hard disk  
drive and power usage is reduced to the same level  
used in the Off state. When the system is in Hibernate  
mode, the Battery Gauge icon is not visible in the  
Status display. In this mode, there is no danger of  
losing data if battery power is lost.  
The suspend action of the Suspend/Resume button  
may be disabled to prevent accidental interruption. If  
this is the case, pressing the Suspend/Resume button  
will not suspend system operation as described here.  
(In this case, suspend mode can only be achieved  
using the system software). Contact your local help  
desk or reseller if your system configuration is not  
suitable.  
If you have successfully performed this procedure,  
system operation is now suspended. Refer to  
“Resuming System Operation” later in this chapter to  
resume system operation. Also, note the following  
with regard to suspending system operation:  
You can remove the battery while the system is in  
Suspend-to-RAM or Hibernate modes in order to  
install a charged battery. To prevent losing unsaved  
If your system is equipped with a PC Card that allows  
you to connect to a wired or wireless network, you  
21  
 
                 
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T w o  
may be logged off the network after a period of  
inactivity while system operation is suspended.  
Here are some hints on using the pen similar to a two-  
button mouse on a desktop system:  
Contact your network administrator or help desk for  
details on log-off parameters for your network.  
To select an object, tap the pen tip on the object  
once. This functions like a left mouse button click.  
RESUMING SYSTEM OPERATION  
To resume system operation from either Suspend-to-  
RAM or Hibernate modes, press the Suspend/Resume  
button.  
To “double-click” an object, tap twice on the object  
quickly. (The pen double-click speed is in sync with  
the mouse double-click speed, and can be changed by  
going to Start-> Settings -> Control Panel -> Mouse.  
From Suspend-to-RAM mode  
To generate a “right mouse button single-click,  
Status lights indicate that the system state is  
changing. It may take up to a minute before the  
system returns to the On state and system operation  
resumes. Note that the display turns on shortly  
before the pen becomes active due to the power-up  
sequences observed by the system.  
press the Right-Click Application Button  
tap on the object once.  
, then  
To move, or “drag, an object on the screen, place the  
pen tip directly over the object, then as you hold the  
pen tip against the screen, move the pen.  
From Hibernate (Save-to-Disk) mode  
Active data is read from the hard disk drive, and the  
system returns to the On state after a short time.  
INSTALLING A PEN TETHER  
To prevent dropping or losing your pen, you should  
attach it to your system using the pen tether that is  
included with the system.  
P O I N T  
To attach the pen tether to your Tablet PC, perform the  
following steps:  
Note that power to several system components must be  
restored before system operation resumes. Allow  
sufficient time for system operation to resume before  
attempting to use the system. If your system uses  
Hibernate mode, it will take longer to resume operation  
as compared to using Suspend-to-RAM mode. Time is  
needed to read data from the hard disk drive.  
1. Attach the end of the pen tether with the smaller  
loop to your pen. Do do so, push the end of the  
tether through the hole in the pen, then thread the  
opposite end of the tether through the loop. (See  
Figure 2-1)  
Use the system as you normally would once system  
operation resumes.  
Pen tether  
attachment  
point  
All programs resume at the point where execution  
stopped when system operation was suspended.  
USING THE PEN  
You can use the Stylistic ST4000P Series pen to select  
items, and to navigate through programs on the pen  
tablet PC. The pen can be used like a two button mouse  
when used in conjunction with the right-mouse button.  
Larger loop  
Smaller loop  
Figure 2-1 Installing a Pen Tether  
C A U T I O N S  
2. Attach the end of the pen tether with the larger loop  
to the attachment point on your pen tablet. To do so,  
insert the end of the pen tether through the attach-  
ment point, then feed the pen through the large loop  
in the tether.  
• Ensure that a screen protector is installed on the pen  
tablet PC screen before you use the pen. The  
warranty does not cover a screen that is scratched as  
a result of not using a screen protector.  
• Use only the pen provided with your pen tablet PC.  
Do not use substitutes that were not designed for the  
Stylistic ST4000P Series pen tablet PC. (e.g., ball  
point pens, fingernail, or screwdriver). Damage  
caused by using an instrument other than the  
provided pen is not covered by the system warranty.  
22  
 
               
U s i n g Yo u r S t y l i s t i c S T 4 0 0 0 P  
If you have successfully performed the procedure above,  
the pen is now recalibrated, and you can use the system as  
you normally would.  
CALIBRATING THE PEN  
Calibration of the pen adjusts the cursor position on the  
screen relative to the position of the pen tip. You calibrate  
the pen to adjust the distance error between where the  
pen actually touches the screen and where the system  
“thinks” the pen is touching. If the event you wish to  
invoke is not displayed under the pen tip when you use  
the pen, you should calibrate the pen.  
Replacing the Pen  
With use, the pen tip may become worn or may pick up  
foreign particles that can scratch the screen. A damaged  
or worn tip may not move freely, causing unpredictable  
results when using the pen. If your pen exhibits these  
problems, contact your reseller to purchase replacements.  
Pen calibration may be required due to the following  
situations:  
The pen is being used for the first time.  
USING HOVERING MODE  
Selecting the Pen Hovering application button on the  
Stylistic ST4000P Series pen tablet PC provides you with  
better cursor control. When the hovering option is  
enabled, the cursor can be positioned over an icon  
without activating it. This is useful when you are  
performing procedures that require accurate cursor posi-  
tioning, such as when simulating mouse rollover,  
selecting a small icon, or beginning a paint session.  
The previous user of the Stylistic ST4000P Series pen  
tablet PC writes with the opposite hand or at a  
different pen angle.  
The system has been in use for some time and the pen  
has not been recalibrated.  
The original system image has been restored.  
To enable hovering, press the Function button  
To Calibrate the Pen  
1. Open the Control Panel from the Start|Settings  
menu, and double-tap the Pen Configuration icon. In  
the Setup Property page, tap on [Calibrate] to start  
calibration.  
and the Right-Click button at the same  
time.  
To disable hovering, press the Function button  
and the Right-Click button again.  
2. Position the Stylistic ST4000P Series pen tablet PC as  
you normally would during use. Be sure to hold the  
pen at the angle that you regularly use. Touch the  
screen only with the pen tip; inadvertently touching  
the screen with your finger or hand during the  
For help on Normal/Special Hover mode settings in the  
Pen Configuration applet, press [F1] to invoke help from  
within the applet.  
calibration process, may result in faulty calibration.  
CHARGING THE BATTERY  
3. Perform the calibration steps according to the  
instructions on the screen. The calibration utility  
displays a cross-hair symbol in the corners of the  
screen, one corner at a time. Hold the pen as you  
normally would while using the system and, as  
accurately as possible, tap the center of each crosshair  
as it is displayed.  
The Stylistic ST4000P Series battery can be charged while  
it is installed in the pen tablet PC. To do so:  
1. Connect a DC power source, such as the AC adapter,  
to the DC input connector on the pen tablet PC. The  
DC Input icon appears in the Status display. If the  
battery charge is below 90%, the battery begins  
charging and the Charging icon appears in the Status  
display. If the battery charge is 90% or higher when  
you connect DC power, the battery will not charge,  
preventing battery overcharging.  
4. When the Verify New Pen Calibration Settings  
window appears, choose one of the following steps.  
If you are satisfied that you tapped the cross-hairs  
accurately, tap Yes. The taps that you performed in  
step 3 are then used to calibrate the screen.  
2. Look at the Battery Gauge icon in the Status display  
to determine the percent of charge in the battery. See  
“Status Display” in Chapter 1 of this manual for a  
description of the Battery Gauge icon.  
If you do not want to use the new calibration, tap  
No.  
As long as DC power remains connected to the pen tablet  
PC, the charging process continues until the battery  
charge reaches 100%. Charge times shown in Table 2-2,  
“Battery Charging Time" are for a fully discharged  
battery charging both while the pen tablet PC is and is  
not in use.  
If you want to enter a new calibration, tap  
Recalibrate. The calibration instructions reappear.  
If you don’t tap the screen within 20 seconds, the  
default settings will be used.  
23  
 
                     
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T w o  
3. Pull the battery away from the system, as shown in  
the illustration and remove the battery from the pen  
tablet PC.  
Approximate  
Charge Time  
(not in use)  
Approximate  
Charge Time  
(in use)  
Battery Charge  
Level Reached  
If you are using an external battery charger, refer to the  
instructions provided with the battery charger.  
90%  
3.5 hours  
4.5 hours  
7 hours*  
8 hours*  
100%  
P O I N T  
Under Federal, state, or local law, it may be illegal to  
dispose of batteries by putting them in the trash. Be  
sure to dispose of batteries in accordance with local  
government regulations.  
Table 2-2 Battery Charging Time  
* Depends upon the applications in use.  
Also note the following with respect to charging the  
battery:  
To install the battery:  
You can use the system, suspend system operation, or  
shut down and turn off the system without  
interrupting the charging process; however, using the  
system while the battery is charging will cause the  
battery to charge at a slower rate, as noted in Table 2-  
2, “Battery Charging Time".  
1. Orient the battery with the slides in the empty  
battery tray. Slide the battery into the tray and press  
it firmly until it is seated. When it is properly seated,  
the battery release latch should return to position  
and lock the battery.  
As noted in the procedure above, the system will not  
begin charging the battery if the battery charge level  
is 90% or higher when the system is initially  
connected to external DC power. (This prevents the  
battery from being overcharged.)  
The Stylistic ST4000P Series battery uses Lithium ion  
battery cells which have no “memory effect.” You do  
not need to discharge the battery before you begin  
charging.  
Figure 2-2 Removing the Battery  
REMOVING AND INSTALLING  
THE BATTERY  
Once the battery is installed, you can resume system  
operation or start and use your system normally.  
The battery can be removed from the pen tablet PC and  
swapped with a charged battery. The battery can then be  
charged in an external charger if one is available. To  
remove the battery from the pen tablet PC:  
TIPS FOR CONSERVING BATTERY POWER  
You can extend the charge life of your battery by  
conserving battery power. (Your results may vary  
depending on your application and how the system is  
configured.) Here are some suggestions to help you  
conserve battery power:  
1. Choose one of the following:  
If a charged battery is available, you can suspend  
system operation. A built-in “bridge” battery will  
maintain the system in Suspend-to-RAM mode  
for about 5 minutes while the battery is removed;  
this allows time for replacement with a charged  
battery.  
Use an external power source such as the AC adapter  
whenever the system is docked.  
Suspend system operation if you know that you  
won’t be using the system for a while.  
If a charged battery is not available, save your  
work and close all running programs, then shut  
down the system or Hibernate (Save-to-Disk).  
Shut down the system if you won’t be using the  
system for an extended period of time.  
Use power management (available on the desktop) to  
help you conserve power automatically.  
2. Slide the battery release latch in the direction  
Battery life is dependent upon the operating system,  
power settings, and applications in use.  
indicated. (See Figure 1 on page 24 for location).  
24  
 
                 
U s i n g Yo u r S t y l i s t i c S T 4 0 0 0 P  
Operation of the Bridge Battery  
PC CARD SLOT  
When installed in the pen tablet PC, the battery provides  
power to some system components—even when the  
system is in the Off state. When the battery is removed,  
power is supplied to these components by a “bridge”  
battery that is built into the pen tablet PC.  
The Stylistic ST4000P Series Pen Tablet PC Card slot  
allows you to install a Type I or Type II PCMCIA Card.  
Installing a PC Card  
To install a PC card, position the side with the arrow  
facing up (i.e., when looking at the tablet’s display side,  
the arrow on the card should be visible.) Slide the card  
into the PC Card slot, and press it firmly to ensure proper  
seating. (See Figure 2-3 for location)  
The bridge battery is not designed for long-term opera-  
tion. To maintain the bridge battery properly, observe the  
following measures:  
P O I N T  
If you need assistance installing a PC Card in the Stylistic  
ST4000P Series pen tablet PC, contact your corporate  
help desk or your reseller.  
• The bridge battery function is disabled if Wake On  
LAN is enabled in the BIOS.  
• The system arrives with the bridge battery in a  
discharged state. Be sure to charge it sufficiently  
before relying upon it to support the system in the  
event of battery removal.  
To prevent draining the bridge battery, always store  
the system with a charged battery installed.  
If the bridge battery becomes drained, it takes  
approximately 8 hours for it to be fully recharged.  
Figure 2-3 Installing a PC Card  
The bridge battery charges when the AC Adapter is  
connected and the system is in On or Off states or  
Suspend mode. It charges from the battery only when  
the system is in the On state.  
Removing a PC Card  
To remove a PC Card, press the PC Card eject button so  
that it pops out. Once the button has popped out, press it  
in firmly to eject the card. (See Figure 2-4 for location)  
MODEM CONNECTION  
P O I N T  
The internal 56 Kbps LAN/modem module installed in  
the Stylistic ST4000P Series pen tablet PC has actual  
maximum transfer rates of 53 Kbps (receive), 33.6 Kbps  
(send), and 14.4 Kbps (fax). Download rates are limited  
to 53 Kbps in the United States due to FCC restrictions.  
The Stylistic ST4000P Series pen tablet PC is designed to  
accept a standard RJ-11 telephone plug. Connect the plug  
to the modem jack located on the left-hand side of the  
pen tablet PC (See Figure 1-4 on page 5 for location). The  
telephone plug can be installed whether or not the pen  
tablet PC has power applied.  
Figure 2-4 Removing a PC Card  
REMOVING AND INSTALLING  
MEMORY MODULES  
There is one DIMM slot in your pen tablet PC and  
256MB on the motherboard. 256MB and 512MB  
modules are available, so you can install a combination of  
up to 768MB in the system.  
If you need assistance configuring the Stylistic ST4000P  
Series pen tablet PC modem or LAN, contact your local  
help desk or your reseller.  
25  
 
               
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T w o  
4. Reinstall the cover and screws that you removed in  
step 2.  
C A U T I O N  
5. Confirm that the DIMM module is recognized by  
the system. To do so, run BIOS Setup. The size of  
the DIMM module should be displayed in the Info  
menu in BIOS Setup.  
DIMM replacement should only be performed at a  
static-free workstation. Avoid touching connector pins,  
circuit boards, and other circuit components on the  
drive or pen tablet PC. Electrostatic discharge caused by  
doing so can damage sensitive components.  
The DIMM module is installed in the pen tablet PC and  
you can now use the system.  
Installing a Memory Module  
To install a DIMM module in the pen tablet PC:  
Removing a Memory Module  
To remove a DIMM module:  
1. Ensure that the pen tablet PC is off. To do so, carry  
out the Shut Down command in the Start menu.  
(Do not attempt to remove or install a DIMM  
module when the system is in Suspend mode or  
running.)  
1. Ensure that the pen tablet PC is off. To do so, carry  
out the Shut Down command in the Start menu.  
(Do not attempt to remove or install a DIMM  
module when the system is in Suspend mode or  
running.)  
2. Remove the two screws from the cover plate on the  
back of the pen tablet PC and remove the cover plate  
as shown in Figure 2-5.  
2. Remove the screws from the cover plate on the back  
of the pen tablet PC and remove the cover plate as  
shown in Figure 2-5.  
3. Spread the fingers on the socket that lock the DIMM  
module in place until the DIMM module is loose.  
The DIMM module is now removed from the pen tablet  
PC. Refer to “Installing a Memory Module” on page 26  
to install a new DIMM module.  
Figure 2-5 Accessing the Memory Slot  
3. Insert the DIMM module in the socket at an angle  
and push it down until it locks into place as shown  
in Figure 2-6. Note that the DIMM module is keyed  
to prevent it from being inserted backwards.  
Figure 2-6 Installing a DIMM Module  
26  
 
       
3
Care and  
Maintenance  
27  
 
     
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T h r e e  
28  
 
C a r e a n d M a i n t e n a n c e  
.
Care and Maintenance  
This chapter gives you pointers on how to care for and  
maintain your Stylistic ST4000P Series pen tablet PC.  
PROTECTING THE DISPLAY SCREEN  
The Stylistic ST4000P Series pen tablet PC is designed to  
provide you with years of service. Using a screen  
protector will help ensure that the screen remains as clear  
as possible. When installed, the screen protector becomes  
a durable, replaceable writing surface that protects the  
display screen from abrasion.  
To obtain additional screen protectors, check with your  
reseller, or go to the Fujitsu Web site at www.fujit-  
supc.com for ordering information. Additional informa-  
tion about installation is included with the screen  
protectors.  
Figure 3-1 Removing the Protective Sheet  
4. Apply the screen protector to the display screen  
surface. When doing so, orient the screen protector  
with the adhesive side of the screen protector facing  
the display screen and the notched corner of the  
screen protector oriented as shown in Figure 3-2.  
C A U T I O N  
During normal use of the pen tablet PC, small particles  
from the environment can become embedded in the  
pen tip and scratch the screen. To prevent scratching  
the screen, ensure that a screen protector is installed  
before using your pen tablet PC. The warranty does not  
cover a screen that is scratched as a result of not using a  
screen protector.  
To install a new screen protector on your pen tablet PC:  
1. If a screen protector is already installed on the display  
screen, remove it before installing the new screen  
protector.  
Figure 3-2 Installing the screen protector  
The screen protector is held onto the display screen  
surface by a thin strip of adhesive around the edges. A  
notch in one corner of the screen protector allows  
you to slide your fingernail under the screen  
protector for easy removal.  
5. Apply pressure to the screen protector with your  
finger using a continuous wiping motion along the  
edges. The adhesive sets completely within 48 hours.  
To ensure a good seal between the screen protector  
and the display, do not lift the screen protector from  
the display once it has been applied.  
2. Clean the display by wiping the screen gently using a  
soft cotton cloth dampened with isopropyl alcohol.  
Ensure that all residue has been removed from the  
screen before applying a new screen protector.  
6. Remove the protective plastic cover from the face of  
the screen protector, as shown in Figure 3-3.  
C A U T I O N  
The Stylistic ST4000P Series pen tablet PC is not  
waterproof. Do not pour liquids on the system or  
wash it with a heavily soaked cloth.  
Do not place items on the top of the display, or dam-  
age may occur.  
3. Remove the protective coating from the adhesive side  
of the screen protector first, as shown in Figure 3-1.  
Figure 3-3 Removing the protective cover  
29  
 
             
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T h r e e  
7. Clean any residue left behind by the protective  
coating from the exposed surface of the screen  
TROUBLESHOOTING  
Solutions to some common problems are described in  
the following sections. If you are experiencing a problem  
with your pen tablet PC that you cannot solve by taking  
the actions described, contact your local help desk or  
your reseller for further assistance.  
protector by wiping gently with a soft cotton cloth  
dampened with isopropyl alcohol. Wipe the screen  
protector with a soft dry cloth to remove any low-  
tack adhesive; this will help prevent the pen tip from  
squeaking.  
System Will Not Resume Operation  
If the system will not resume operation after system  
operation has been suspended, check the following  
possible causes:  
The screen protector is now installed.  
STORING THE PEN TABLET PC  
Store the Stylistic ST4000P Series pen tablet PC in the  
Off state with a fully charged battery installed. You can  
store the pen tablet PC in the Off state for about 30 days  
with a fully charged battery installed. After this period,  
the battery should be recharged or replaced with a  
charged battery.  
The battery may either be defective, or discharged to  
a critically low level. When the battery reaches a  
critically low level, the system is forced into Suspend-  
to-RAM mode to avoid a total system power failure.  
To correct this problem, either connect an external  
power supply (such as the AC adapter), or install a  
charged battery in the pen tablet PC.  
If you intend to store the pen tablet PC for a longer  
period of time, the small battery that maintains system  
time may need to be replaced. Replacement of the clock  
battery should only be performed by authorized techni-  
cians.  
The system may be at the critical thermal limit. To  
avoid damage to heat-sensitive components, the  
system enters Suspend-to-RAM mode when it gets  
too hot. System operation cannot be resumed until  
the pen tablet PC cools off to a tolerable temperature.  
Move the pen tablet PC to a cooler location.  
AVOIDING OVERHEATING  
The pen tablet PC monitors its internal temperature. As  
the internal temperature approaches the tolerable limits  
of heat-sensitive components, system functions are  
automatically limited or turned off to prevent damage.  
Display Screen Blank or Difficult to Read  
If the display screen on your pen tablet PC appears blank  
or is unreadable, confirm that the system is running (the  
Power icon is displayed continuously on the Status  
display), and check the following:  
To avoid overheating the pen tablet PC, do not obstruct  
the air vents on the top and bottom edges of the pen  
tablet PC.  
The system brightness may be set too low, causing  
the screen to appear too dark. To change system  
brightness, press the Fn button twice to open the  
Fujitsu menu. Brightness can be adjusted from the  
menu.  
CLEANING THE DISPLAY SCREEN  
To clean the pen tablet PC display screen, wipe the  
screen surface gently using a soft cotton cloth slightly  
dampened with water or isopropyl alcohol.  
An external monitor may be selected. Press the Fn  
and Display Select buttons to determine whether the  
pen tablet PC display screen is selected.  
C A U T I O N  
The video timeout may have expired. Tap on the  
display screen to reactivate the display. Note that this  
is a normal, power-saving feature.  
The Stylistic ST4000P Series pen tablet PC is not  
waterproof. Do not pour liquids on the pen tablet PC or  
wash the pen tablet PC with a heavily soaked cloth.  
Cursor Is Not Tracking Pen  
If the cursor on the screen appears to be misaligned with  
the pen or is not accurately tracking the pen, calibrate  
the pen. See “To Calibrate the Pen” on page 23 for more  
information.  
Infrared Data Transfer Is Not Working  
If you are experiencing problems transferring data over  
the system’s infrared interface, note the following:  
Can the IrDA port on the pen tablet PC “see” the  
30  
 
                         
C a r e a n d M a i n t e n a n c e  
IrDA port on the other device? A direct line-of-sight  
path must exist between the IrDA port on the pen  
tablet PC and the IrDA port on the other device.  
The distance between the two devices must not be  
more than 3 feet.  
The viewing angle from the IrDA port on the pen  
tablet PC must not be more than 15 degrees from a  
center line between the IrDA port on the pen tablet  
PC and the IrDA port on the other device.  
The device with which you are trying to communicate  
must be compliant with the IrDA Standard Revision  
1.1 (or 1.0).  
It may be necessary for both computers to be using  
the same network connection protocols.  
Pen Tablet PC is Not Responding to the Pen  
If the pen tablet PC does not respond to the pen, connect  
an external keyboard to the system to see if it responds to  
keyboard commands. If the system doesn’t respond to a  
keyboard, the application or system may have crashed,  
and it may be necessary to reset the system. If the system  
responds to a keyboard but not to a pen, contact your  
local help desk or reseller for further assistance.  
Speaker/Headphone Volume Too Low  
If the audio volume on your pen tablet PC speaker or  
external headphones is too low, check the following:  
Ensure that the speaker (or headphone output if using  
headphones) is enabled. To do so, open the Control  
Panel and double-click on the Sounds and Audio  
Devices icon. Select the proper tab, and increase the  
volume using the slider bar. (If you aren’t getting any  
sound, uncheck the Mute box if it is checked.)  
Press the Fn button twice to open the Fujitsu menu.  
Volume can be adjusted from the menu.  
Ensure that the mute box in the system volume  
control (accessible from the system tray) is not set.  
Ensure that any volume control in your audio  
software is set to an audible level.  
Configuring Peripheral Interfaces  
Certain peripheral devices can be disabled during the  
BIOS Setup. If the peripheral interface you want to use  
does not appear to be working with your peripheral  
device, ensure that it is enabled in the BIOS. Contact  
your local help desk or reseller if you need assistance  
using BIOS Setup.  
31  
 
     
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n T h r e e  
32  
 
4
Specifications  
33  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n F o u r  
34  
 
S y s t e m S p e c i f i c a t i o n s  
Stylistic ST4000P Series Hardware Specifications  
The following table provides general hardware  
specifications of the Stylistic ST4000P Series pen tablet  
Stylistic ST4000P Specifications (Continued)  
PC by category.  
Display Specifications  
3
Display  
• Color LCD  
Stylistic ST4000P Specifications  
Physical Specifications  
• Passive Touch Panel  
• 16-bit color  
3
• 10.4” TFT XGA (1024 x 768), 260K  
colors  
Dimensions  
Weight  
11.86” w x 8.66” d x 0.82”-0.88” h  
(301.3mm x 220mm x 20.9-22.3mm)  
• Brightness: 8 levels  
• Viewing Angle:  
3.2 lbs. (1.45 Kg)  
Horizontal: 30 degrees (min.)  
Vertical: 10 degrees (min.)  
Processing Specifications  
3
• Contrast Ratio:  
Typ. 250, Min. 100  
CPU  
Ultra low voltage Mobile Intel Pentium  
III processor - M with SpeedStep  
technology*  
VRAM  
Intel 830MG chipset with 8MB shared  
memory using Unified Memory  
Chip set  
Intel 830MG - 133 MHz  
800 MHz*  
Architecture (UMA) delivers low-  
power, high-performance 3D/2D  
graphics, video, and display capabilities.  
Dynamic Video Memory Technology  
(DVMT) dynamically responds to  
application requirements and efficiently  
allocates the proper amount of memory  
(48MB max.) for optimal graphics and  
system performance.  
Processor  
Speed  
Memory/Storage Specifications  
3
Main RAM  
• 256MB SDRAM (on-board/  
PC133).  
• 144-pin SO DIMM modules  
256MB and 512MB module  
configurations available, with a system  
maximum of 768MB.  
Interface Specifications  
3
PC Card  
Slots  
• One Type I or Type II  
• PCMCIA CardBus version 3.0  
L1 cache  
(CPU)  
32 KB on-die  
Integrated  
Interfaces  
• Modem (RJ-11)  
• LAN (RJ-45)  
L2 cache  
512 KB on-die  
8 Mbit (FWH)  
• IEEE 1394 (S400 4-pin)  
• USB (Qty. 2)  
• DC-In  
BIOS ROM  
Hard disk  
drive  
• 2.5” HDD  
• 15-pin D-SUB connector for  
external VGA monitor  
• Minimum 20GB IDE HDD*  
• Ultra DMA 100  
• Shock-mounted  
• Docking connector  
Infrared  
IrDA version 1.1 (FIR, 4Mbps)  
35  
 
           
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n F o u r  
Stylistic ST4000P Specifications (Continued)  
Stylistic ST4000P Specifications (Continued)  
Keyboard/  
Mouse  
support  
• Keyboard/Mouse IR Port  
• System IR Port  
• 6-cell NiMH, 35 mAh  
Bridge  
Battery  
• Life (with Suspend-to-RAM on  
bridge battery only):  
5 minutes from full charge  
Audio  
• SigmaTel STAC9767 codec  
• Autosensing 100 - 240V, supplying  
16 VDC, with a current of 3.75 A  
• Internal mono microphone and  
speaker  
AC Adapter  
• Mono microphone and headphone  
jacks  
Environmental Specifications  
3
o
o
o
o
Temperature  
Humidity  
Operating: 41 - 95 F (5 - 35 C)  
User  
Controls  
• Application Buttons, with primary,  
secondary, and tertiary functions  
o
o
Non-operational: 5 - 140 F  
o
o
• Power On/Suspend/Resume  
button  
(-15 - 60 C)  
Operating: 20 - 85% non-condensing  
Non-operating: 8 - 85% non-  
condensing  
• Emergency Shutoff Button (Power  
Off button)  
• Two Navigation buttons  
Agency Approval Specifications  
3
Status  
• Power  
Indicators  
(LEDs)  
• Charge/DC-In  
• Battery level  
• HDD  
• EN55022 (CISPR22) Class B  
• FCC 15, Class B  
• FCC 15C, 15.247  
• DOC Class B  
• Hovering  
Emissions  
Immunity  
• ETSI EN 300-328  
• ICES-003  
* The specifications for your particular model may vary.  
To determine the specifications for your system, please  
• Canada RSS-210  
Power Specifications  
3
• EN55024 (1998)  
• ETSI EN 301-489-17 V.1.1.1  
(2000-9)  
Main Battery  
• 6-cell  
• Removable, Lithium ion  
• 10.8 V @ 4000 mAh  
• Warm-swappable  
• UL and cUL Listed, UL 1950, 3rd  
edition  
Safety  
• TuV T-Mark, EN60950  
• Recharge Time:  
Suspend/Off: 3.5 hours (90%), 4.5  
hours (100%)  
Operating: 8 hours (100%)  
• FCC Part 68  
• IC CS-03  
Telecom  
Life: Up to 5 hours. (Battery life is  
dependent upon the operating  
system, power management, and  
applications in use.)  
Additional Specifications  
3
Operating  
systems  
• Microsoft Windows 2000  
Professional  
• Suspend Life: Minimum 5 days  
Off State: Approximately 30 days  
• Microsoft Windows XP  
Professional  
36  
 
       
5
Agency Notices  
37  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n F i v e  
38  
 
A g e n c y N o t i c e s  
This equipment is designed to be connected to the tele-  
phone network or premises wiring using a standard  
modular jack type USOC RJ-11C which is FCC Part 68  
compliant and a line cord between the modem and the  
telephone network with a minimum of 26AWG.  
Regulatory Information  
C A U T I O N  
Changes or modifications not expressly approved by  
Fujitsu could void this user’s authority to operate the  
equipment  
The REN is used to determine the number of devices that  
you may connect to your telephone line and still have all  
of those devices ring when your number is called. Too  
many devices on one line may result in failure to ring in  
response to an incoming call. In most, but not all, areas  
the sum of the RENs of all of the devices should not  
exceed five (5). To be certain of the number of devices  
you may connect to your line, as determined by the  
RENs, contact your local  
NOTICE  
Changes or modifications not expressly approved by  
Fujitsu could void this user’s authority to operate the  
equipment.  
telephone company.  
FCC NOTICES  
Notice to Users of Radios and Television  
If this equipment causes harm to the telephone network,  
your telephone company may discontinue your service  
temporarily. If possible, they will notify you in advance. If  
advance notice is not practical they will notify you as  
soon as possible. You will also be advised of your right to  
file a complaint with the FCC.  
These limits are designed to provide reasonable protec-  
tion against harmful interference in a residential installa-  
tion. This equipment generates, uses, and can radiate  
radio frequency energy and, if not installed and used in  
accordance with the instructions, may cause harmful  
interference to radio communications. However, there is  
no guarantee that interference will not occur in a partic-  
ular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be  
determined by turning the equipment off and on, the  
user is encouraged to try to correct the interference by  
one or more of the following measures:  
This fax modem also complies with fax branding require-  
ments per FCC Part 68.  
Your telephone company will probably ask you to discon-  
nect this equipment from the telephone network until  
the problem is corrected and you are sure that the equip-  
ment is not malfunctioning. This equipment may not be  
used on coin-operated telephones provided by your tele-  
phone company. Connection to party lines is subject to  
state tariffs. Contact your state’s public utility commis-  
sion, public service commission or corporation commis-  
sion for more information.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and  
receiver.  
Connect the equipment into an outlet that is on a  
different circuit than the receiver.  
Consult the dealer or an experienced radio/TV  
This equipment includes automatic dialing capability.  
When programming and/or making test calls to  
emergency numbers:  
technician for help.  
Shielded interconnect cables must be employed with this  
equipment to ensure compliance with the pertinent RF  
emission limits governing this device.  
Remain on the line and briefly explain to the  
dispatcher the reason for the call.  
Perform such activities in off-peak hours, such as early  
Notice to Users of the US Telephone Network  
Your pen tablet PC may be supplied with an internal  
modem which complies with Part 68 of the FCC rules.  
On the system is a label that contains the FCC Registra-  
tion Number and the Ringer Equivalence Number (REN)  
for this equipment among other information. If  
requested, the user must provide their telephone  
company with the following information:  
morning or late evening.  
FCC rules prohibit the use of non-hearing aid compatible  
telephones in the following locations or applications:  
All public or semi-public coin-operated or credit card  
telephones.  
Elevators, highways, tunnels (automobile, subway, rail-  
road or pedestrian) where a person with impaired  
hearing might be isolated in an emergency.  
Places where telephones are specifically installed to  
1. The telephone number to which the computer is  
connected.  
alert emergency authorities such as fire, police or  
medical assistance personnel.  
Hospital rooms, residential health care facilities, conva-  
2. The Ringer Equivalence Number (REN) for this  
equipment.  
3. The equipment requires a standard modular jack  
type USOC RJ-11C which is FCC Part 68 compliant.  
lescent homes and prisons.  
Stores where telephones are used by patrons to  
order merchandise.  
4. The FCC Registration Number.  
39  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n F i v e  
Public transportation terminals where telephones are  
used to call taxis or to reserve lodging or rental cars.  
In hotel and motel rooms as at least ten percent of the  
rooms must contain hearing aid-compatible tele-  
phones or jacks for plug-in hearing aid compatible  
telephones which will be provided to hearing impaired  
customers on request.  
Avis Aux Utilisateurs Du Réseau  
Téléphonique Canadien  
AVIS: Le présent matériel est conforme aux spécifica-  
tions techniques d’Industrie Canada applicables au  
matériel terminal. Cette conformité est confirmée par le  
numéro d’enregistrement. Le sigle IC, placé devant le  
numéro d’enregistrement, signifie que l’enregistrement  
s’est effectué conformément à une déclaration de  
conformité et indique que les spécifications techniques  
d’Industrie Canada ont été respectées. Il n’implique pas  
qu’Industrie Canada a approuvé le matériel.  
DOC (INDUSTRY CANADA) NOTICES  
Notice to Users of Radios and Television  
This Class B digital apparatus meets all requirements of  
Canadian Interference-Causing Equipment Regulations.  
Avant de connecter cet équipement à une ligne télépho-  
nique, l’utilisateur doit vérifier s’il est permis de  
connecter cet équipement aux installations de télécom-  
munications locales. Lutilisateur est averti que même la  
conformité aux normes de certification ne peut dans  
certains cas empêcher la dégradation du service.  
CET appareil numérique de la class B respecte toutes les  
exigence du Réglement sur le matérial brouilleur du  
Canada.  
Notice to Users of the Canadian Telephone Network  
NOTICE: This equipment meets the applicable Industry  
Canada Terminal Equipment Technical Specifications.  
This is confirmed by the registration number. The  
abbreviation, IC, before the registration number signi-  
fies that registration was performed based on a Declara-  
tion of Conformity indicating that Industry Canada  
technical specifications were met. It does not imply that  
Industry Canada approved the equipment.  
Les réparations de l’équipement de télécommunications  
doivent être eVectuées par un service de maintenance  
agréé au Canada. Toute réparation ou modification, qui  
n’est pas expressément approuvée par Fujitsu, ou toute  
défaillance de l’équipement peut entraîner la compagnie  
de télécommunications à exiger que l’utilisateur décon-  
necte l’équipement de la ligne téléphonique.  
Before connecting this equipment to a telephone line the  
user should ensure that it is permissible to connect this  
equipment to the local telecommunication facilities.  
The user should be aware that compliance with the  
certification standards does not prevent service  
degradation in some situations.  
AVIS: Lindice d’équivalence de la sonnerie (IES) du  
présent matériel est de 0.0. LIES assigné à chaque  
dispositif terminal indique le nombre maximal de  
terminaux qui peuvent être raccordés à une interface  
téléphonique. La terminaison d’une interface peut  
consister en une combinaison quelconque de dispositifs,  
à la seule condition que la somme d’indices d’équiva-  
lence de la sonnerie de tous les dispositifs n’excède pas 5.  
Repairs to telecommunication equipment should be  
made by a Canadian authorized maintenance facility.  
Any repairs or alterations not expressly approved by  
Fujitsu or any equipment failures may give the telecom-  
munication company cause to request the user to  
disconnect the equipment from the telephone line.  
AV E R T I S S E M E N T  
Pour assurer la sécurité, les utilisateurs doivent vérifier  
que la prise de terre du service d’électricité, les lignes  
télphoniques et les conduites d’eau métalliques sont  
connectées ensemble. Les utilisateurs NE doivent PAS  
tenter d’établir ces connexions eux-mêmes, mais  
doivent contacter les services d’inspection d’installations  
électriques appropriés ou un électricien. Ceci peut être  
particulièrement important en régions rurales.  
NOTICE: The Ringer Equivalence Number (REN) for  
this terminal equipment is 0.0. The REN assigned to  
each terminal equipment provides an indication of the  
maximum number of terminals allowed to be connected  
to a telephone interface. The termination on an interface  
may consist of any combination of devices subject only  
to the requirement that the sum of the Ringer Equiva-  
lence Numbers of all the devices does not exceed five.  
C A U T I O N  
For safety, ensure that the electrical ground of the  
power utility, the telephone lines and the metallic water  
pipes are connected together. Do NOT attempt to make  
such connections themselves but should contact the  
appropriate electric inspection authority or electrician.  
This may be particularly important in rural areas.  
40  
 
A g e n c y N o t i c e s  
UL Notice  
This unit requires an AC adapter to operate. Use only UL  
Listed Class 2 Adapters with an output rating of 16 VDC,  
with a current of 3.75 A.  
AC Adapter output polarity:  
+
C A U T I O N  
The modem-to-telephone network connection must be  
a line cord using a minimum #26 AWG wire.  
For Authorized Repair Technicians Only  
W A R N I N G S  
For continued protection against risk of fire, replace  
only with the same type and rating fuse.  
Danger of explosion if Lithium (clock) battery is incor-  
rectly replaced. Replace only with the same or equiva-  
lent type recommended by the manufacturer. Dispose  
of used batteries according to the manufacturer’s  
instruction.  
System Disposal  
In the event of system disposal, please observe the  
following information regarding proper procedures in  
the State of Vermont.  
The liquid crystal display (LCD) lamps used in this  
system contain mercury. In the event of system  
disposal, be sure to follow local guidelines.  
41  
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s U s e r ’ s G u i d e  
S e c t i o n F i v e  
42  
 
Appendix  
Wireless LAN* User’s Guide  
* Optional device  
43  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
44  
 
W i r e l e s s L A N U s e r s G u i d e  
FCC Interference Statement  
FCC REGULATORY INFORMATION  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interfer-  
ence in a residential installation. This equipment gener-  
ates, uses, and can radiate radio frequency energy. If not  
installed and used in accordance with the instructions, it  
may cause harmful interference to radio communica-  
tions. However, there is no guarantee that interference  
will not occur in a particular installation.  
Please note the following regulatory information related  
to the optional wireless LAN device.  
Regulatory Notes and Statements  
Wireless LAN, Health and Authorization for use  
Radio frequency electromagnetic energy is emitted from  
Wireless LAN devices. The energy levels of these emis-  
sions, however, are far much less than the electromag-  
netic energy emissions from wireless devices such as  
mobile phones. Wireless LAN devices are safe for use by  
consumers because they operate within the guidelines  
found in radio frequency safety standards and recom-  
mendations. The use of Wireless LAN devices may be  
restricted in some situations or environments, such as:  
If this equipment does cause harmful interference to  
radio or television reception, which can be determined  
by turning the equipment off and on, the user is encour-  
aged to try and correct the interference by one or more  
of the following measures:  
1. Reorient or relocate the receiving antenna.  
On board an airplane, or  
2. Increase the distance between the equipment and  
the receiver.  
In an explosive environment, or  
In situations where the interference risk to other  
devices or services is perceived or identified as  
harmful.  
3. Connect the equipment to an outlet on a circuit  
different from the one the receiver is connected to.  
4. Consult the dealer or an experienced radio/TV  
technician for help.  
In cases in which the policy regarding use of Wireless  
LAN devices in specific environments is not clear (e.g.,  
airports, hospitals, chemical/oil/gas industrial plants,  
private buildings), obtain authorization to use these  
devices prior to operating the equipment.  
FCC Radio Frequency Exposure statement  
This Wireless LAN radio device has been evaluated  
under FCC Bulletin OET 65C and found compliant with  
the requirements as set forth in CFR 47 Sections 2.1091,  
2.1093, and 15.247 (b) (4) addressing RF Exposure from  
radio frequency devices. The radiated output power of  
this Wireless LAN device is far below the FCC radio  
frequency exposure limits. Nevertheless, this device shall  
be used in such a manner that the potential for human  
contact during normal operation is minimized. When  
using this device, a certain separation distance between  
antenna and nearby persons must be maintained to  
ensure RF exposure compliance. In order to comply with  
RF exposure limits established in the ANSI C95.1 stan-  
dards, the distance between the antennas and the user  
should not be less than 20 cm (8 inches).  
Regulatory Information/Disclaimers  
Installation and use of this Wireless LAN device must be  
in strict accordance with the instructions included in the  
user documentation provided with the product. Any  
changes or modifications made to this device that are  
not expressly approved by the manufacturer may void  
the user’s authority to operate the equipment. The  
manufacturer is not responsible for any radio or televi-  
sion interference caused by unauthorized modification  
of this device, or the substitution or attachment of  
connecting cables and equipment other than those spec-  
ified by the manufacturer. It is the responsibility of the  
user to correct any interference caused by such unautho-  
rized modification, substitution or attachment. The  
manufacturer and its authorized resellers or distributors  
will assume no liability for any damage or violation of  
government regulations arising from failure to comply  
with these guidelines.  
Export restrictions  
This product or software contains encryption code  
which may not be exported or transferred from the US  
or Canada without an approved US Department of  
Commerce export license. This device complies with  
Part 15 of FCC Rules., as well as ICES 003 B / NMB 003  
B. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received,  
including interference that may cause undesirable oper-  
ation. Modifications not expressly authorized by Fujitsu  
PC Corporation may invalidate the user's right to  
operate this equipment.  
Federal Communications Commission statement  
This device complies with Part 15 of FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause interference, and, (2) This  
device must accept any interference, including interfer-  
ence that may cause undesired operation of this device.  
45  
 
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
To improve this situation, you can use a wireless LAN  
access point, which is sold separately. The wireless LAN  
network is in the “Infrastructure mode” when it uses an  
access point, and such a connection is called the “Infra-  
structure Network.”  
BEFORE USING THIS DEVICE  
Thank you for purchasing a Fujitsu ST4000P Series Pen  
Tablet PC with the optional Integrated Wireless LAN.  
This manual describes the basic operating procedures  
for the Wireless LAN (referred to as the “device” in this  
manual) and how to set up a wireless LAN network.  
Before using this device, read this manual carefully to  
ensure correct operation of the device. Keep this manual  
in a safe place for reference while using the device.  
By using an access point, you can set and use a different  
communication channel for each network group. Each  
channel is given a different radio frequency, and it  
eliminates the collision of communications and provides  
a more stable communications environment. Infrastruc-  
ture mode is most suitable when you are configuring  
multiple wireless LAN networks on the same floor.  
Characteristics of the Device  
This device consists of a wireless LAN card that is  
attached to the computer via a mini-PCI slot.  
To connect a wireless LAN network to a wired LAN, you  
need an access point.  
The main characteristics are as follows:  
It uses the power saving communications system in  
the 2.4 GHz band, and does not require any license for  
radio communication.  
How to Handle This Device  
If you purchased the wireless LAN option, the Integrated  
Wireless LAN device is already installed in your ST4000P  
Series Pen Tablet PC. Under normal circumstances, it  
should not be necessary for you to remove or re-install  
it. The LAN has been configured to support the oper-  
ating system with which your system shipped.  
It uses Direct Sequence Spread Spectrum (DS-SS),  
which is resistant to noise.  
This device complies with Wi-Fi, and is able to com-  
municate at the maximum transfer rate of 11 Mbps.  
The maximum communication range is approxi-  
The On/Off switch located on the Wireless LAN cover  
turns the device on and off. You should switch the device  
off when it is not in use in order to maximize battery life.  
mately 80 feet (25 meters) inside a building. The  
range may be shorter depending upon the installation  
factors, such as walls and columns.  
Unauthorized access can be prevented with the use of  
SSID and encryption key.  
Wireless LAN Modes Using this Device  
AdHoc Mode  
The AdHoc Mode” refers to the network connecting  
two computers using wireless LAN cards. This connec-  
tion is called an AdHoc network.”  
Using an AdHoc network, you can obtain a network  
connection easily and at a low cost.  
In the AdHoc mode, you can use the function supported  
by Microsoft Network, such as File and Print Sharing to  
exchange files and share a printer or other peripheral  
devices.  
To use the AdHoc Mode, you must set the same SSID  
and the same encryption key for all the computers that  
are connected. All connected computers can communi-  
cate with each other within the communication range.  
Infrastructure Mode  
If a number of computers are connected simultaneously  
in the AdHoc mode, the transfer rate may be reduced,  
communications may become unstable, or the network  
connection could fail. This is because all wireless LAN  
cards are using the same radio frequency in the network.  
46  
 
     
W i r e l e s s L A N U s e r s G u i d e  
CONNECTING WINDOWS 2000 SYSTEMS  
This chapter describes how to set the wireless LAN  
connection for computers running Windows 2000.  
Item  
Description  
Not supported.  
Power  
Save  
Enabled  
P O I N T  
If you pruchased a ST4000P Series Pen Tablet PC with  
the wireless LAN option, the integrated wireless LAN  
device and drivers have already been installed. This  
procedure outlines the steps for setting the device  
parameters.  
AdHoc  
Channel  
AdHoc Network: Select the same  
channel, 1-11, for all connected  
computers. If there is more than one  
wireless LAN nearby (such as on the  
same floor), we recommend that the  
channels for each LAN be 5 numbers  
apart (e.g., if there are two other LANs  
nearby, the channels used should be 1,  
6, and 11).  
Updated drivers and/or utilities may become available  
after this manual is printed; see any addenda or fliers  
that may be included in the system packaging.  
Infrastructure Network: Not an option.  
Workflow  
The proper setup of the wireless LAN requires several  
steps which must be performed in the proper order.  
Following is a general outline of the steps that must be  
performed. Each step is detailed later in this procedure.  
Table 1: Profile Parameters  
5. Click the [Encryption] tab.  
6. Set the encryption items in accordance with Table 2.  
1. Setting parameters  
AdHoc Network: Specify the same value for all the  
computers for which the encryption key is used for  
connection.  
Setting the profile  
Setting the encryption  
Infrastructure Network: Specify the identical encryp-  
2. Network settings  
tion keys to the encryption keys set for the access  
point. For instructions on how to check the encryp-  
tion keys set for the access point, refer to the access  
point manual.  
Setting the protocol and checking the network  
Setting file and printer sharing  
Checking the connection  
P O I N T  
Setting Parameters  
Make sure that you specify the encryption keys. If you  
do not specify the keys, any computer with a wireless  
LAN card can be connected. This presents a risk that  
your data may be stolen or destroyed.  
1. Click [Start]-> [Settings] -> [Control Panel].  
2. Double-click the [PRISM Settings] icon. The  
[PRISM Wireless Settings] appears.  
3. Set the profile as specified in Table 1. Ask your  
network administrators to check the setting.  
Item  
Description  
4. When you finish your entry, click [Apply].  
Encryption  
(WEP)  
Click the down arrow and select an  
encryption option.  
Item  
Profile  
Description  
Disable: Disables the encryption. In  
Enter the system file name in which the  
parameter information is to be saved.  
this case, “Create keys with Pass-  
phrase” and subsequent items are  
greyed out, and you cannot enter  
anything.  
Mode  
Ad Hoc Network: Click the down arrow  
and select “802.11 AdHoc”.  
40 bit*: The encryption is set.  
Select either “Create keys with  
Passphrase”, “Create keys manu-  
ally”, or “ASCII Input”, and enter  
the encryption keys.  
Infrastructure Network: Click the down  
arrow and select “Infrastructure”.  
SSID  
Enter the network name to which you  
want to connect  
104 bit*: The encryption is set.  
Select either “Create keys with  
Passphrase”, “Create keys manu-  
ally”, or “ASCII Input”, and enter  
the encryption keys.  
Transmit  
Rate  
Obtain the information from your  
network administrator. If you do not  
have a network administrator, select  
“Fully Automatic”.  
47  
 
   
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
closer to the wireless LAN standard. For consistency, the  
Windows 2000 utilities reflect the same modes.  
Item  
Description  
Not supported.  
Outside of wireless LAN environments, encryption is  
generally set at either 64 bit or 128 bit. However, the  
wireless LAN standard requires that 24 bits be reserved  
for fixed data. As a result, the user can only use 40 bits  
(64 minus 24) or 104 bits (128 minus 24) for encryption.  
This requirement also fixes the number of characters  
used for 128 bit encryption to 13 which is calculated as  
(13 x 8 bits = 104).  
Create Keys  
with  
Passphrase  
Passphrase  
Not supported.  
Create Keys  
Manually  
Select this to use hexadecimal  
character codes to set the encryption  
keys (Keys 1 - 4).  
(Hexadecimal  
Input)  
Enter a 10-digit value when you have  
selected [40 bit]* for the encryption.  
Enter a 26-digit value when you have  
selected [104 bit]* for encryption.  
NETWORK CONNECTION: WINDOWS 2000  
The section describes how to set the network connection  
for a computer with Windows 2000.  
Select if the network contains a card  
that is set with the encryption key  
using the character code. Specify the  
encryption keys with the same value  
used for other wireless LAN cards  
that are already set.  
Network Settings  
In this section, you set “TCP/IP Settings,and complete  
“Checking Computer Name and Workgroup,” required  
for the network connection.  
TCP/IP Settings  
ASCII Input  
Select to use the ASCII codes to set  
encryption keys (Keys 1 - 4). Select  
this if network does not contain other  
wireless LAN cards that are set with  
encryption key using character codes.  
1. Click [Start] -> [Settings] -> [Control Panel].  
2. Double-click the [Network and Dial-up  
Connections] icon. The [Network and Dial-up  
Connections] window appears.  
Enter a 5-digit value when you have  
selected [40 bit]* for the encryption.  
Enter a 13-digit value when you have  
selected [104 bit]* for encryption.  
3. Right click the [Local Area Connection], then click  
[Properties] from the menu that appears. The [Local  
Area Connection Properties] window appears.  
You can use the following characters:  
0 - 9, A - Z, a - z, _ (underscore).  
P O I N T  
For example, to set “ABC12” for the  
encryption key, enter “ABC12.”  
More than one network adapter is installed in your  
system if more than one [Local Area Connection] entry  
is displayed. In this case, select the [Local Area  
Connection] entry with [Intersil PRISM Wireless LAN  
PCI Card] displayed under [Device Name].  
Default Key  
Click the down arrow, and select a  
key from Keys 1 - 4.  
Table 2: Encryption Key Setup  
4. Perform the following steps.  
7. When you finish your entry, click [Apply].  
8. Click [OK]. [PRISM Wireless Settings] closes.  
You have completed the parameter settings.  
Click [Internet Protocol (TCP/IP)].  
Click [Properties]. The [Internet Protocol (TCP/IP)  
Properties] window appears.  
P O I N T  
When using ADSL (PPPoE) with the infrastructure  
network to connect to the Internet, you must change  
the computer’s MTU size set. To change MTU size, refer  
to the manual that comes with the access point.  
* 40 bit and 104 bit encryption is the wireless LAN  
equivalent of 64 bit and 128 bit encryption, as set by  
Microsoft and wireless LAN manufacturers. This is the  
same encryption rate that is used by the Windows XP  
operating system, and was selected in order to align it  
48  
 
   
W i r e l e s s L A N U s e r s G u i d e  
5. Set an IP address as indicated in Table 3. Ask your  
network administrator to check the setting.  
Item  
Workgroup  
Description  
A name for the network group:  
Item  
Description  
AdHoc Network:  
Specify the same name to all com-  
puters within the same network.  
For AdHoc  
Network  
Set the IP address and subnet mask:  
Click [Use the following IP address],  
and enter a value for [IP address] and  
[Subnet mask].  
Infrastructure Network: Specify a  
workgroup name to connect to.  
To change the setting, click  
[Properties], and follow the instruc-  
tions on the screen. [System Proper-  
ties] appears again.  
Refer to “Setting IP Addresses” on  
page 58 to set an IP address and  
subnet mask.  
For  
Select [Obtain an IP address  
automatically]:  
Table 4: Checking computer name and workgroup  
Infrastructure  
Network  
5. Click [OK]. When a message appears prompting you  
to restart the computer, click [Yes].  
For the DNS server, select [Obtain  
DNS server address automatically].  
For the IP address, DNS server, and  
default gateway, follow the network  
administrator's instructions, if any.  
Sharing  
In this section, you set sharing of the drive, folder, and  
printer.  
You only need to set this when you are sharing files or a  
printer with other computers on the network.  
Table 3: Setting an IP Address  
6. Click [OK]. The [Local Area Connection Properties]  
window appears again.  
When you share a drive, folder, or printer, you can use  
them from any computer on the network.  
7. Click [OK]. When a message appears prompting you  
to restart the computer, click [Yes].  
Setting [File and Printer Sharing for Microsoft  
Networks]  
Checking the full computer name and workgroup  
1. Click [Start] -> [Settings] -> [Control Panel].  
1. Click [Start] -> [Settings] -> [Control Panel].  
2. Double-click the [Network and Dial-up  
Connections] icon. The [Network and Dial-up  
Connections] windows appears.  
2. Double-click the [System] icon. [System Properties]  
appears.  
3. Click the [Network Identification] tab.  
3. Right click the [Local Area Connection], then click  
[Properties] from the menu that appears. [Local  
4. Check [Full computer name] and [Workgroup]. Ask  
your network administrator and check the setting.  
Area Connection Properties] appears.  
P O I N T  
More than one network adapter is installed in your  
system if more than one [Local Area Connection] entry  
is displayed. In this case, select the [Local Area Connec-  
tion] entry with [Intersil PRISM Wireless LAN PCI Card]  
displayed under [Device Name].  
Item  
Description  
Full  
A name to identify the computer on  
the network. You can specify any  
name to each computer.  
Computer  
Name  
For easier identification, use the model  
name or user name.  
4. If [File and Printer Sharing for Microsoft Networks]  
is displayed in the list, make sure that it is checked. If  
it is not checked, check it and click [OK]. You do not  
have to perform the following steps. Go to the next  
section, entitled “Sharing Files.”  
If [File and Printer Sharing for Microsoft Networks]  
is not found in the list, click [Install], and perform  
Step 5 and subsequent steps. When you click  
[Install], the [Select Network Component Type]  
window appears.  
49  
 
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
5. Perform the following steps.  
3. Click [Sharing], and select necessary items.  
Click [Service].  
Click [Add]. The [Select Network Service] window  
Item  
Description  
appears.  
6. Perform the following steps.  
Not Shared  
Shared As  
Disables printer sharing.  
Enables printer sharing.  
Click [File and Printer Sharing for Microsoft  
Networks].  
Click [OK]. You will go back to [Local Area Connec-  
Share Name  
Specifies a share name of the  
printer to be shared.  
tion Properties], and [File and Printer Sharing for  
Microsoft Networks] is added to the list.  
Comment  
Passwords  
Enter the description of the printer  
to be shared.  
7. Click [OK].  
P O I N T  
If you specify a password, you  
need to enter it when using the  
printer.  
If you have changed the setting, [Close] is shown  
instead. Click [Close].  
Table 6: Printer Sharing  
Sharing Files  
The following example shows how to set sharing the  
“Work” folder on the c: drive.  
4. Click [OK]. The printer sharing is set, and the icon  
changes.  
1. On the desktop, double-click [My Computer]->  
C: drive.  
Checking the Connection  
After the network setting is completed, access the shared  
drive on another computer to check the connectivity of  
the wireless LAN network.  
2. Right-click the “Work” folder, then click [Sharing]  
from the menu. The [Work Properties] window  
appears.  
Accessing Another Computer  
3. Click [Share this folder] and set necessary items, as  
indicated in the following table.  
1. Double-click the [My Network Places] icon on the  
desktop. [My Network Places] appears.  
2. Double-click [Computers near me]. The computers  
that are connected to the network are displayed.  
Item  
Description  
3. Double-click the computer that you want to access.  
The drive that you set with “Sharing” are displayed.  
Share name  
You can specify a share name for the  
drive or folder that you want to share.  
4. Double-click the drive that you want to access. The  
drive is displayed showing its contents and made  
available to you. If you have any questions or prob-  
lems, refer to “Troubleshooting Table” on page 55.  
Comment  
User limit  
You can enter the description for the  
drive or folder that you want to share.  
Specifies the limit for the number of  
sharing users.  
Checking the Connectivity  
Permissions  
Caching  
Specifies the folder access privileges.  
Specifies the caching for the folder.  
1. Click [Start] -> [Settings] -> [Control Panel].  
2. Double-click the [PRISM Settings] icon. [PRISM  
Wireless Settings] appears.  
3. Check the connectivity on the [Link] tab. The  
current condition of connection is displayed.  
Table 5: Sharing files  
4. Click [OK]. The folder is set shared, and the “Work”  
folder icon changes.  
Printer Sharing  
1. Click [Start] -> [Settings] -> [Printers]. The Printers  
window appears, showing the printers that are  
connected.  
2. Right click the printer that you want to share, then  
click [Sharing] from the menu that appears.  
50  
 
W i r e l e s s L A N U s e r s G u i d e  
Workflow  
The proper setup of the wireless LAN connection  
requires that several steps be performed in the proper  
order. Following is a general outline of the steps to be  
performed. Each step is detailed later in this procedure.  
Item  
Description  
State  
Shows the current condition of  
connection.  
1. Setting parameters  
Setting the profile  
The MAC address of the other  
computer to which you are  
Setting the encryption  
connected is displayed when the  
connection is successful. If you are  
connected to more than one  
computer, the computer that has  
the best connectivity is displayed.  
2. Network settings  
Setting the protocol and checking the network  
Setting file and printer sharing  
Checking the connection  
Current Channel  
Current Tx Rate  
Shows the current channel used  
for the connection.  
Setting Parameters  
1. Click [Start] -> [Control Panel].  
Shows the current transfer rate in  
Mbits/sec.  
2. Click [Network and Internet connections].  
[Radio Off]/  
[Radio On]  
Click [Radio Off] to disconnect.  
3. Click [Network connection]. A list of networks that  
are currently installed is displayed.  
Click [Radio On] to connect to the  
network.  
4. Right click [Intersil PRISM Wireless LAN PCI Card]  
in the list, and click [Properties] from the menu that  
is displayed. [Wireless Network Connection Proper-  
ties] appears.  
[Rescan] button  
Click this button to search for  
others to connect to.  
5. Click the [Wireless Networks] tab. The [Wireless  
Networks] tab appears.  
Throughput  
(Bytes/sec)  
Shows the actual transfer rate of  
the data transfer for send (Tx) and  
receive (Rx).  
6. Perform the following steps.  
Make sure that [Use Windows to configure my wire-  
Link Quality  
Shows either [Excellent], [Good],  
[Fair], [Poor], or [Not Connected],  
depending on the link quality.  
less network settings] is checked.  
Click [Add] under [Preferred networks]. [Wireless  
Network Properties] appears.  
7. Set parameters in accordance with Table 8.  
Not shown for AdHoc connection.  
For the AdHoc network, specify the same value to all  
the computers, for which the encryption key is used  
for connection.  
Signal Strength  
Shows either [Excellent], [Good],  
[Fair], [Poor], or [Not Connected],  
depending on the signal strength.  
For the infrastructure network, specify the encryp-  
Not shown for AdHoc connection.  
tion key (network key) with the same value to the  
encryption key of the access point. For how to check  
the encryption keys set for the access point, refer to  
the manual supplied with the access point.  
Table 7: Checking connectivity  
CONNECTING WINDOWS XP SYSTEMS  
This chapter describes how to set up the wireless LAN  
connection for computers that are running Windows XP.  
P O I N T  
Be sure to specify the encryption keys. If you do not  
specify the keys, any computer with a wireless LAN card  
can be connected. This presents a risk that other users  
may steal or destroy your data.  
P O I N T  
If you purchased a ST4000P Series Pen Tablet PC with  
the wireless LAN option, the integrated wireless LAN  
device and drivers have already been installed. This  
procedure outlines the steps for setting the device  
parameters.  
Updated drivers and/or utilities may become available  
after this manual is printed; see any addenda or fliers  
that may be included in the system packaging.  
51  
 
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
Item  
Description  
P O I N T  
Network  
Name  
SSID  
Enter the network name to which you  
want to connect. This is a required item.  
For the network name, ask your LAN  
administrator.  
If [Wireless Network Connection 2 Properties] is not  
displayed, click [Start] -> [Settings] -> [Control Panel],  
and double-click the [Network Connection] icon.  
Right click the [Wireless Network Connection], and  
then click [Properties] from the menu that appears.  
AdHoc network: Set the same name for all  
of the computers that are to be connected.  
Infrastructure network: Specify the same  
name as that specified on the access point  
that is to be connected. For access point  
instructions, refer to the manual that  
comes with the access point.  
2. Perform the following steps.  
Click [Internet Protocol (TCP/IP)].  
Click [Properties]. [Internet Protocol (TCP/IP)  
Properties] appears.  
3. Set an IP address. Ask your network administrator  
and check the setting.  
Key  
Format  
Click the down arrow and select the input  
for the Network key.  
ASCII  
characters  
Select this when using  
ASCII characters for the  
Network Key. Characters  
that can be used follow:  
Item  
AdHoc  
Description  
Set the IP address and subnet mask.  
Enter a value for [IP address] and  
[Subnet mask]. See “Setting IP  
Addresses” on page 58 to set IP  
address and subnet mask.  
Network  
0-9, A-Z, a-z, and  
_ (underscore)  
Example: To set the key to  
“ABC12”, input “ABC12”.  
For  
Select [Obtain an IP address  
Hexa-  
decimal  
characters  
Select this when using  
hexadecimal characters for  
the Network Key.  
Infrastructure  
Network  
automatically]. For the DNS server,  
select [Obtain DNS server address  
automatically]. For the IP address,  
DNS server, and default gateway,  
follow the network administrator's  
instructions, if any.  
Use this if there is a wireless  
LAN card in the network  
that has the Network Key  
set to a character code. In  
’Network Key’, input the  
same value as the other  
wireless LAN card.  
Table 9: Setting an IP address  
5. Click [OK].  
P O I N T  
Table 8: Setting parameters  
If you have changed the setting, [Close] is shown  
instead. Click [Close].  
8. When you finish your entry, click [OK]. [Wireless  
Network Connection 2 Properties] appears again.  
9. Make sure the network name you specified for the  
SSID in Step 7 is added under [Preferred networks].  
6. Close [Network Connection].  
Checking the Full Computer Name and Workgroup  
Network Connection  
The section describes how to set the network connection  
for a computer running Windows XP.  
1. Click [Start] -> [Control Panel]. Make sure the  
Classic View is selected.  
2. Double-click the [System] icon. [System Properties]  
appears.  
Network Settings  
3. Click the [Computer Name] tab.  
In this section, you set “TCP/IP Settings,and complete  
“Checking Computer Name and Workgroup” required  
for the network connection.  
TCP/IP Settings  
1. On [Wireless Network Connection Properties], click  
[General].  
52  
 
 
W i r e l e s s L A N U s e r s G u i d e  
4. Check [Full computer name] and [Workgroup]. Ask  
your network administrator and check the setting.  
[Install], [Select Network Component Type]  
appears.  
5. Perform the following steps.  
Click [Service].  
Click [Add]. [Select Network Service] appears.  
Item  
Description  
6. Perform the following steps.  
Computer  
Name  
A name to identify the computer on  
the network. You can specify any  
name to each computer. Use up to 15  
single-byte characters. For easier  
identification, use the model name or  
user name.  
Click [File and Printer Sharing for Microsoft  
Networks].  
Click [OK]. You will go back to [Wireless Network  
Connection 2 Properties], and [File and Printer  
Sharing for Microsoft Networks] is added to the list.  
7. Click [Close].  
Workgroup  
A name of the network group. Use up  
to 15 single-byte characters.  
Sharing Files  
AdHoc Network: Specify the same  
name to all computers within the  
same network.  
The following example shows how to set sharing the  
Work” folder on the c: drive.  
1. Click [Start] -> [My Computer].  
Infrastructure Network:  
Specify workgroup name to connect  
to.  
2. Double-click the [Local Disk (c:)] icon.  
3. Right click the “Work” folder, and then click  
[Sharing and Security] from the menu that appears.  
[Work Properties] appears.  
Table 10: Setting computer name and workgroup  
4. Click [If you understand the security risks but want  
to share files without running the wizard, click  
To change the setting, click [Change], and follow the  
instructions on the screen. [System Properties] appears  
again.  
here].  
P O I N T  
5. Click [OK]. When a message appears prompting you  
to restart the computer, click [Yes].  
If you have already clicked [If you understand the  
security risks but want to share files without running the  
wizard, click here], this window does not appear.  
Sharing  
In this section, you set sharing of the drive, folder, and  
printer.  
In the [Work Properties] window, the description under  
[Network Sharing and security] changes.  
You need to set this only when you are sharing files or a  
printer with other computers on the network.  
5. Check [Share this folder on the network].  
Uncheck [Allow network users to change my files], if  
the shared folder is for read only.  
When you share a drive, folder, or printer, you can use  
these from any computer on the network.  
Setting [File and Printer Sharing for Microsoft  
Networks]  
6. Click [OK]. The folder is set shared, and the “Work”  
folder icon changes.  
1. Click [Start] -> [Control Panel]. Make sure the  
Classic View is selected.  
Printer Sharing  
1. Press [Start]->[Control Panel] (or [Settings], if  
viewing in Classic mode)-> [Printers and Faxes].  
The Printers and Faxes display will appear and the  
connected printers will be displayed.  
2. Double-click the [Network Connection] icon.  
3. Right click the [Wireless Network Connection], and  
then click [Properties] from the menu that appears.  
[Wireless Network Connection Properties] appears.  
2. Right-click the printer to be shared, and click  
[Sharing] from the menu that appears. The proper-  
ties of the printer to be shared will be displayed. Set  
printer sharing.  
4. If [File and Printer Sharing for Microsoft Networks]  
is displayed in the list:  
Make sure that it is checked. If it is not checked,  
check it, and click [OK]. You do not have to perform  
the following steps. Go to the next section, “Sharing  
Files.”  
On the display, the printer sharing setting is recom-  
mended by the Network Setup Wizard, but for the wire-  
less LAN network, security is maintained by network  
name (SSID) or network key. The following steps allow  
you to set up printer sharing without using the Network  
Setup Wizard.  
If [File and Printer Sharing for Microsoft Networks]  
is not found in the list, click [Install], and perform  
Step 5 and the subsequent steps. When you click  
53  
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
3. Click 'If you understand the security risks but want  
to share printers without running the wizard, click  
here. 'Enable Printer Sharing' will be displayed.  
Item  
Description  
Current Tx  
Rate  
Shows the current transfer rate in  
Mbits/sec.  
4. Select 'Just enable printer sharing'.  
5. Click 'OK'. The printer properties will be indicated.  
6. Select 'Share this printer'.  
Radio Off/  
Radio On  
Click [Radio OFF] to disconnect.  
Click [Radio On] to connect to the  
network.  
7. Enter the sharing printer name in 'Share name'.  
8. Click OK. The printer will be shared, and the printer  
icon will become a sharing icon.  
Rescan  
Click this button to search for others  
to connect to.  
Checking the Connection  
Throughput  
(Bytes/sec)  
Shows the actual transfer rate of the  
transfer data for send (Tx) and receive  
(Rx).  
After the network setting is completed, access the shared  
drive on another computer to check the connectivity of  
the wireless LAN network.  
Link Quality  
Shows the link quality. This is not  
shown for the AdHoc connection.  
Accessing Another Computer  
1. Click [Start] -> [My Computer].  
Signal  
Strength  
Shows the signal strength.  
2. From the left menu in [Other Places], click [My  
Network Places].  
This is not shown for the AdHoc  
connection.  
3. From the left menu in [Network Tasks], click [View  
workgroup computers]. The workgroup in which  
you are participating will appear.  
Table 11: Checking connectivity  
4. Double click the computer to which you want to  
connect. The drive that you set in [Computer  
Sharing] appears.  
5. Double click the drive to which you want to connect.  
The contents of the drive will appear, and is available  
for use.  
If you have a question or problem, refer to “Trouble-  
shooting Table” on page 55.  
Checking the Connectivity  
1. Click [Start] -> [Control Panel].  
2. Double-click the [PRISM Settings] icon. [PRISM  
Wireless Setting] appears.  
3. Check the connectivity on the [Link] tab. The  
current condition of connection is displayed  
Item  
State  
Description  
Shows the current condition of  
connection.  
The MAC address of the other  
computer that you are connected to is  
displayed, when the connection is  
successfully made. If you are  
connected to more than one  
computer, the computer that has the  
best connectivity is displayed.  
Current  
Channel  
Shows the current channel used for  
the connection.  
54  
 
W i r e l e s s L A N U s e r s G u i d e  
TROUBLESHOOTING  
This section contains troubleshooting information, including causes and actions, for problems you may find while using  
this device.  
Troubleshooting Table  
Problem  
Possible Cause  
A failure to  
Possible Solution  
An exclamation mark  
(!) or cross (x) is  
attached to [Intersil  
PRISM Wireless LAN  
PCI Card].  
Restart the computer.  
Restart the computer.  
recognize the device.  
A failure in installing  
the driver.  
Other computers are  
not displayed when  
the [Network  
Computer] icon is  
double-clicked.  
The network has not  
been set up correctly.  
Check the setting for the protocol, workgroup, and sharing.  
To check this, you need a different procedure, depending upon the  
operating system that you use. Refer to the appropriate section of  
this chapter.  
It takes time before  
the network is  
searched and the  
computer connected  
is displayed.  
Perform the following steps to search for the computer.  
Click [Start] -> [Search] -> [Other Computers].  
Enter the computer name that you are connecting to in [Name],  
and click [Search].  
Double-click the icon of the computer that has been searched.  
A failure in installing  
the driver.  
Make sure that the driver is correctly installed.  
The TCP/IP protocol  
is not installed, or,  
the IP address is not  
set correctly.  
Make sure that the TCP/IP protocol is installed. To check this, you  
need a different procedure, depending on the operating system that  
you use. Refer to the appropriate section of this manual.  
The TCP/IP protocol  
is not installed, or,  
the IP address is not  
set correctly.  
If the TCP/IP protocol is installed, do the following to check the IP  
address:  
1. Windows 2000:  
Click [Start] -> [Programs] -> [Accessories] -> [Command  
Prompt].  
Windows XP:  
Click [Start] -> [All Programs] -> [Accessories] ->  
[Command Prompt].  
2. Enter “IPCONFIG” command, and press [Enter].  
(If your hard disk is C drive, enter  
C:\>ipconfig)  
Check that the IP address is correctly displayed under the IP Address.  
Example:  
IP address: 10.0.1.3  
Subnet Mask: 255.255.255.0  
Default Gateway: 10.0.1.1  
No communication  
due to poor radio  
signal.  
Shorten the distance between computers or remove visible obstacles  
between them, and retry the connection.  
55  
 
     
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
Problem  
Possible Cause  
Possible Solution  
IP packet isn’t  
reaching its  
destination  
Run the PING  
command to check  
the connection  
Perform the following steps to run the PING command to check if the  
IP packet is correctly delivered to the destination.  
To run the PING command, the TCP/IP protocol must be installed.  
First you will determine your IP address, then you will make sure your  
IP address can respond, and then you will make sure other computers  
can be addressed.  
1. Windows 2000: Click [Start] -> [Programs] -> [Accessories] -  
> [Command Prompt].  
Windows XP: Click [Start] -> [All Programs] -> [Accessories] ->  
[Command Prompt].  
2. Type: ipconfig > directory\filename  
where directory and filename represent the location at which  
you want to store the IP address.  
3. Click [Enter], then go to the location you specified above. The  
IP address for your system will be contained in the file.  
4. To check that your IP address is functioning properly, go back  
to the DOS prompt and type: ping <IP address>, then press  
[Enter]. You will receive several replies, followed by the PING  
statistics (similar to below).  
5. To check that your system is communicating with other  
systems, go to the DOS prompt and type:  
\>ping XXX.XXX.XXX.XXX. (With the destination IP address  
in place of XXX.XXX.XXX.XXX).  
Example: if the destination IP address is 10.0.1.3:  
C:\>ping 10.0.1.3  
A message similar to the following appears if the connection is  
successful.  
Pinging 10.0.1.3 with 32 bytes of data:  
Reply from 10.0.1.3: bytes=32 time=1ms TTL=32  
Reply from 10.0.1.3: bytes=32 time<10ms TTL=32  
Reply from 10.0.1.3: bytes=32 time=4ms TTL=32  
Reply from 10.0.1.3: bytes=32 time<10ms TTL=32  
If the connection fails, [Request timed out], [Destination host  
unreachable], or a similar message appears. In this case, refer to the  
“Other computers are not displayed” portion of this chapter.  
Cannot connect to  
the network  
There are several  
possible causes, as  
listed to the right.  
Refer to the  
specific section of this  
manual or your user’s  
manual.  
The following causes are possible. Check each one of them.  
The network name or encryption key is not right.  
The driver has not correctly started.  
The destination computer is not turned on.  
You do not have the access privilege to the destination computer.  
The card has failed.  
Hardware conflict.  
56  
 
W i r e l e s s L A N U s e r s G u i d e  
Problem  
Possible Cause  
Possible Solution  
I want to remove the  
driver  
(Windows 2000)  
Windows 2000:  
When removing the driver, make sure that the device is attached to  
the computer. If you try to remove the driver while the device is  
detached from the computer, the driver is not removed.  
1. Right click the [My Computer] icon on the desktop, and then  
click [Properties] from the menu that appears. [System Proper-  
ties] appears.  
2. Click the [Hardware] tab.  
3. Click [Device Manager...]. The [Device Manager] window  
appears.  
4. Click [+] beside [Network adapters].  
5. Right click [Intersil PRISM Wireless LAN PCI Card], and  
click [Uninstall] from the menu that is displayed. [Confirm  
Device Removal] appears.  
6. Click [OK].  
7. Close [System Properties]. Make sure that the icon has disap-  
peared from the task tray in the lower right corner of the screen.  
8. Click [Start] -> [Settings] -> [Control Panel].  
9. Double-click [Add/Remove Programs]. [Add/Remove Pro-  
grams] appears.  
10. Perform the following steps.  
Click [PRISM 11Mbps Wireless LAN for Windows].  
Click [Change/Remove].  
11. A window appears asking you if you really want to remove the  
driver.  
12. Click [Yes]. When the driver is removed, a window appears  
showing that the driver has been removed.  
13. Click [OK].  
14. Close [Add/Remove Programs] and [Control Panel].  
15. Shut down Windows, and turn off the computer.  
57  
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
Problem  
Possible Cause  
Possible Solution  
Windows XP:  
I want to remove  
the driver  
(Windows XP)  
When removing the driver, make sure that the device is attached to  
the computer. If you try to remove the driver while the device is  
detached from the computer, the driver is not removed.  
1. Click [Start], right click [My Computer], and then click [Proper-  
ties] from the menu that appears. [System Properties] appears.  
2. Click the [Hardware] tab.  
3. Click [Device Manager].  
4. Click [+] beside [Network adapters].  
5. Right click [Intersil PRISM Wireless LAN PCI Card], and  
click [Uninstall] from the menu that is displayed. [Confirm  
Device Removal] appears.  
6. Click [OK].  
7. Close [System Properties].  
8. Make sure that the icon has disappeared from the task tray in  
the lower right corner of the screen.  
9. Click [Start] -> [Control Panel]. [Control Panel] appears.  
10. Double-click [Add/Remove Programs]. [Add/Remove Pro-  
grams] appears.  
11. Perform the following steps.  
Click [PRISM 11Mbps Wireless LAN for Windows].  
Click [Change/Remove].  
A window appears asking you if you really want to remove  
the driver.  
12. Click [Yes]. When the driver is removed, a window appears  
showing that the driver has been removed.  
13. Click [OK].  
14. Close [Add/Remove Programs] and [Control Panel].  
15. Shut down Windows, and turn off the computer.  
If no access point is found in the network:  
ABOUT IP ADDRESSES  
Setting IP Addresses  
If you are not sure how to set the IP address, refer to the  
following procedure.  
An IP address is expressed with four values in the range  
between 1 and 255.  
Set the each computer as follows: The value in paren-  
theses is a subnet mask.  
If you have an access point (DHCP server) on the  
network, set the IP address as follows:  
<Example>  
Computer A: 192.168.100.2 (255.255.255.0)  
Windows 2000: [Obtain an IP address automatically]  
Windows XP: [Obtain an IP address automatically]  
Computer B: 192.168.100.3 (255.255.255.0)  
Computer C: 192.168.100.4 (255.255.255.0)  
:
:
P O I N T  
Computer X: 192.168.100.254 (255.255.255.0)  
A DHCP server is a server that automatically assigns IP  
addresses to computers or other devices in the network.  
There is no DHCP server for the AdHoc network.  
If the IP address is already assigned to the computer in  
the network, ask the network administrator to check the  
IP address to be set for the computer.  
58  
 
   
W i r e l e s s L A N U s e r s G u i d e  
SPECIFICATIONS  
Technical Specifications for Integrated Wireless LAN Device  
Item  
Description  
Network Type  
Transfer Rate  
Frequency Range  
Channels  
IEEE 802.11b  
11/5.5/2/1Mbps (auto change)  
2,412 - 2,462 MHz  
One of 11 channels is used  
Non-intelligent  
Card Type  
VCC  
Class B  
Security  
Network name, encryption key  
Windows 2000 Professional, Windows XP Professional  
Max: 350mA  
Supported Operating Systems  
Power Current  
Maximum number of units recommended for  
wireless LAN (AdHoc network)  
10 or less  
59  
 
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s P e n T a b l e t P C U s e r ’ s G u i d e  
A p p e n d i x  
60  
 
I n d e x  
Index  
Conventions Used in the Guide . . . . . . . . . . . . . . . . . .v  
critically low battery level . . . . . . . . . . . . . . . . . . . . . . .21  
A
Application Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
orientation button . . . . . . . . . . . . . . . . . . . . . . . . . 10  
right-click button . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
tertiary functions . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
not tracking pen . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
DC power connector . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
DIMM card, removing . . . . . . . . . . . . . . . . . . . . . . . . .26  
B
screen is blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
screen, cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
battery gauge icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
battery pack  
External Monitor Connector . . . . . . . . . . . . . . . . . . . . .6  
overcharge protection . . . . . . . . . . . . . . . . . . . . . . . 23  
removing and installing . . . . . . . . . . . . . . . . . . . . . 24  
will not begin charging . . . . . . . . . . . . . . . . . . . . . . 23  
Fujitsu Online . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .v  
Fujitsu PC Contact Information . . . . . . . . . . . . . . . . . .v  
battery power  
conserving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Hibernate mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
battery release latch . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
hovering mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
bridge battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Built-in Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
hovering mode icon . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
C
I
Charge/DC input icon . . . . . . . . . . . . . . . . . . . . . . . . . 8  
charging the battery pack . . . . . . . . . . . . . . . . . . . . . . 23  
IEEE 1394 jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
infrared data transfer not working . . . . . . . . . . . . . . .30  
61  
 
 
infrared keyboard port . . . . . . . . . . . . . . . . . . . . . . 3, 14  
infrared keyboard/mouse port . . . . . . . . . . . . . . . . . . . 7  
P
PC Card slot . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 14, 25  
Pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 7  
interfaces  
IrDA port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
IrDA/FIR port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
pen  
not responding . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31  
replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23  
K
peripheral connectors . . . . . . . . . . . . . . . . . . . . . . . . . .14  
Kensington lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
power icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8, 20  
blinking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20, 21  
not displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20  
Kensington lock slot . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
L
Power On/Suspend/Resume  
Local Area Network (LAN) . . . . . . . . . . . . . . . . . . . . 15  
low-battery warning . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
problems, solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
protecting the display screen . . . . . . . . . . . . . . . . . . . .29  
M
microphone jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
resuming system operation . . . . . . . . . . . . . . . . . .22, 30  
RJ-45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15  
modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
N
speaker/headphone volume too low . . . . . . . . . . . . . .31  
Navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
navigation buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
O
optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
battery icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
hard disk drive access icon . . . . . . . . . . . . . . . . . . . . .9  
power icon, blinking . . . . . . . . . . . . . . . . . . . . . . . . .20  
power icon, system states indicated by . . . . . . . .8, 20  
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Power Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
Storage Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2  
storing the system unit . . . . . . . . . . . . . . . . . . . . . . . . .30  
Stylistic ST4000P  
accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
overheating, avoiding . . . . . . . . . . . . . . . . . . . . . . . . . 30  
62  
 
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 4, 5, 6, 7  
items included with . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30  
turning off the system . . . . . . . . . . . . . . . . . . . . . . . . . .20  
Physical Specifications . . . . . . . . . . . . . . . . . . . . . . 35  
power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
Processing Specifications . . . . . . . . . . . . . . . . . . . . 35  
Using . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19  
using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22  
suspend mode, determining . . . . . . . . . . . . . . . . . . . . 21  
Suspend/Resume  
Windows 2000 Professional . . . . . . . . . . . . . . . . . . . .v, 1  
Windows XP Professional . . . . . . . . . . . . . . . . . . . . .v, 1  
suspending system operation . . . . . . . . . . . . . . . . . . . 20  
Wireless LAN  
Suspend-to-RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46  
modes  
system interface connector . . . . . . . . . . . . . . . . . . . . . . 4  
Off state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
On state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . .48  
Windows 98 . . . . . . . . . . . . . . . . . . . . . . . . . . .48  
system status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
system will not resume operation . . . . . . . . . . . . . . . 30  
Wireless LAN module . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Wireless LAN On/Off switch . . . . . . . . . . . . . . . . . . . . .4  
T
Tablet Dock latch point . . . . . . . . . . . . . . . . . . . . . . 4, 7  
Tablet Dock port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
63  
 
S t y l i s t i c S T 4 0 0 0 P S e r i e s  
64  
 

Electro Voice Microphone 660A User Manual
Fisher Price Hearing Aid H4609 User Manual
Frigidaire Range 316135932 User Manual
Fujitsu Air Conditioner AOU18RLXFZ User Manual
GE Air Cleaner AFHC32AM User Manual
GE Convection Oven JT930 User Manual
Gemini Musical Instrument PS 767 User Manual
GE Monogram Oven PSB9240DF User Manual
GE Monogram Refrigerator ZIS36N User Manual
Gianni Industries Door KT 10 User Manual