Extron electronic Switch VYC 100N User Manual

User’s Manual  
YCV 100  
S-Video Encoder  
VYC 100N and VYC 100P  
Composite Video Decoder  
Extron USA-West Extron USA-East Extron EMEA  
Extron Asia  
Extron Japan  
Extron China  
Extron Middle East  
Headquarters  
+800.633.9876  
+800.3987.6673  
+800.7339.8766  
+81.3.3511.7655  
+81.3.3511.7656 FAX  
+400.883.1568  
+971.4.2991800  
+971.4.2991880 FAX  
Inside USA / Canada Only  
Inside Europe Only  
Inside Asia Only  
Inside China Only  
+800.633.9876  
68-779-01 Rev. C  
Inside USA / Canada Only  
+1.919.863.1794  
+1.919.863.1797 FAX  
+31.33.453.4040  
+31.33.453.4050 FAX  
+65.6383.4400  
+65.6383.4664 FAX  
+86.21.3760.1568  
+86.21.3760.1566 FAX  
08 08  
+1.714.491.1500  
+1.714.491.1517 FAX  
© 2008 Extron Electronics. All rights reserved.  
 
FCC Class A Notice  
This equipment has been tested and found to comply with the limits for a  
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates,  
uses and can radiate radio frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause harmful interference to radio  
communications. Operation of this equipment in a residential area is likely to  
cause harmful interference, in which case the user will be required to correct the  
interference at his own expense.  
N
This unit was tested with shielded cables on the peripheral devices. Shielded  
cables must be used with the unit to ensure compliance.  
 
Table of Contents  
Chapter 1 • Introduction.......................................................... 1-1  
About the YCV 100, VYC 100N, and VYC 100P........1-2  
Features......................................................................................1-2  
Chapter 2 • Installation and Operation..........................2-1  
Mounting the YCV 100, VYC 100N and VYC 100P .2-2  
Tabletop use ........................................................................... 2-2  
UL rack mounting guidelines.................................................2-2  
Rack mounting .......................................................................2-3  
Back of the rack installation..................................................2-4  
Furniture mounting ............................................................... 2-5  
Projector mounting................................................................2-6  
Front Panel Features........................................................... 2-6  
Rear Panel Features and Cabling ..................................2-7  
YCV 100 ................................................................................. 2-7  
VYC 100N and VYC 100P .......................................................2-8  
Troubleshooting....................................................................2-10  
Appendix A • Specifications, Part Numbers,  
and Accessories ............................................................................. A-1  
Specifications ......................................................................... A-2  
Included Parts ......................................................................... A-4  
Optional Accessories........................................................... A-4  
All trademarks mentioned in this manual are the properties of their respective owners.  
68-779-01 Rev. C  
08 08  
i
YCV 100, VYC 100N, VYC 100P • Table of Contents  
 
Table of Contents, cont’d  
YCV 100, VYC 100N, and VYC 100P  
Chapter One  
1
Introduction  
About the YCV 100, VYC 100N and VYC 100P  
Features  
ii  
YCV 100, VYC 100N, VYC 100P • Table of Contents  
 
Introduction  
About the YCV 100, VYC 100N, and VYC 100P  
YCV 100, VYC 100N, and VYC 100P  
The Extron YCV 100 is a high-performance S-video to  
composite video encoder. It combines S-video Y and C  
(luminance and chrominance) signals into a composite video  
signal. The encoder is compatible with NTSC 3.58, NTSC 4.43,  
PAL, and SECAM signals. The unit accepts S-video input on two  
female BNC connectors or one 4-pin mini DIN connector and  
outputs composite video on one female BNC connector.  
The Extron VYC 100N and VYC 100P are composite video to  
S-video decoders. It separates a composite video signal into  
S-video Y and C signals. The VYC 100N decodes NTSC 3.58  
signals only and the VYC 100P decodes PAL signals only. Both  
decoders accept composite video input on one female BNC  
connector and outputs S-video signals on two female BNC  
connectors and/or one 4-pin mini DIN connector.  
All units include an external 12 V power supply that accepts  
100-240 VAC 50/60 Hz input.  
Features  
Chapter Two  
Furniture, projector, and rack mountability — The YCV 100,  
VYC 100N, and VYC 100P can be mounted under a desk,  
podium, or other furniture, or secured to a projector  
mount with optional brackets. Alternatively, they can be  
mounted on an optional VersaTools® or universal rack  
shelf.  
2
Versatile S-video input/output configuration — The encoder  
and decoder can pass S-video signals via two female BNC  
connectors or one 4-pin mini DIN connector.  
Installation and Operation  
Extron  
Mounting the YCV 100, VYC 100N, and VYC 100P  
Front Panel Features  
YCV 100  
S-Video  
Encoder  
T
U
O
O
E
ID  
V
IN  
O
E
ID  
V
E
IT  
S
Extron  
YCV 100  
VYCPO100  
EO  
I
D
O
R
E
D
M
V
-
CO  
V
DE  
O
R
S
E
E
C
E
ID  
D
N
O
C
R
R
E
E
W
T
W
O
U
O
N
P
P
O
O
S-  
E
ID  
V
-
S
VYC 100N  
Composite Video  
Decoder  
X
X
A
V
2
A
A
2V  
A
M
1
1
0
M
.5  
.
5
0
Monitor  
Composite  
Video  
Rear Panel Features and Cabling  
Troubleshooting  
A
V
S
88  
AV  
RS232  
M
R
R
7
8
L
R
R
5
6
L
L
R
3
4
L
L
R
R
S
T
1
2
U
P
T
L
U
O
R
R
7
8
L
R
R
5
6
L
L
R
3
4
L
R
R
1
2
T
S
U
P
N
C
L
L
N
Y
I
S
I
S
T
U
P
T
U
O
7
8
5
6
3
4
VTR  
Composite  
Video  
1
2
S
T
U
P
IN  
7
8
5
6
3A  
0.  
3
4
0V  
24  
0-  
10  
1
2
Extron  
z
0H  
-6  
50  
MAV 88 SVA  
Video-  
Conferencing  
S-Video  
AV Matrix  
Switcher  
DVD Player  
S-Video  
YCV 100, VYC 100N, VYC 100P • Introduction  
1-2  
 
Installation and Operation  
Rack mounting  
Mounting the YCV 100, VYC 100N, & VYC 100P  
For optional rack mounting, do not install the rubber feet.  
The YCV 100, VYCN, and VYC 100P can be set on a table or  
mounted on a rack shelf, under a desk or tabletop, or on a  
projector mount.  
Mount the YCV 100, VYC 100N, or YCV 100P, on a VersaTools™  
rack shelf (RSF 123, Extron part #60-190-20; RSB 123,  
part #60-604-21), or on a 6" deep rack shelf (RSU 126,  
part #60-190-10; RSB 126, part #60-604-11), or on a 1U universal  
rack shelf (RSU 129, part #60-190-01; RSB 129, #60-604-02).  
Tabletop use  
Four self-adhesive rubber feet are included with the YCV 100,  
VYC 100N, and VYC 100P. For tabletop use, attach one foot at  
each corner of the bottom side of the unit and place the unit in  
the desired location.  
On the standard rack shelf, the YCV 100, VYC 100N, and  
VYC 100P mount in one of eight locations to the rear of the  
shelf or in one of eight locations to the front of the shelf.  
1.  
Remove rubber feet if they were previously installed on  
the bottom of the unit.  
UL rack mounting guidelines  
The following Underwriters Laboratories (UL) guidelines  
pertain to the safe installation of the YCV 100, VYC 100N, and  
VYC 100P in a rack.  
2.  
Mount the unit on the rack shelf, using two 4-40 x 3/16"  
screws in opposite (diagonal) corners to secure the unit to  
the shelf.  
1.  
Elevated operating ambient temperature — If installed in  
a closed or multi-unit rack assembly, the operating  
ambient temperature of the rack environment may be  
greater than room ambient temperature. Therefore,  
install the unit in an environment compatible with the  
maximum ambient temperature (Tma = +122 °F, +50 °C)  
specified by Extron.  
3.  
Install blank panel(s) or other unit(s) on the rack shelf.  
VersaTools  
Rack Shelf  
2.  
3.  
4.  
Reduced air flow — Install the equipment in a rack so that  
the amount of air flow required for safe operation of the  
equipment is not compromised.  
Mechanical loading — Mount the equipment in the rack  
so that a hazardous condition is not achieved due to  
uneven mechanical loading.  
D
IS  
T
R
IB  
U
T
IO  
N
A
M
P
L
IF  
IE  
R
Circuit overloading — Connect the equipment to the  
supply circuit and consider the effect that circuit  
overloading might have on overcurrent protection and  
supply wiring. Appropriate consideration of equipment  
nameplate ratings should be used when addressing this  
concern.  
Quarter Rack Width  
False Front Face Plate  
Eighth Rack Width  
False Front Face Plate  
(2) 4-40 x 3/16"  
screws  
5.  
Reliable earthing (grounding) — Maintain reliable  
grounding of rack-mounted equipment. Pay particular  
attention to supply connections other than direct  
connections to the branch circuit (e.g. use of power strips).  
Mounting the YCV 100, VYC 100N, and VYC 100P on  
a VersaTools rack shelf  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-2  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-3  
 
Installation and Operation  
2.  
Mount the unit on the rack using the two included rack  
screws. It can be vertically mounted facing in either  
direction, as shown here.  
0
.2  
1
A
2
P
V
O
M
W
C
O
A
X
E
R
B
A
B
A
A
U
N
L
BU  
V
E
L
/U  
D
/U  
I
O
R
N
N
B
T
E
B
A
C
102  
A
R
L
L
L
O
U
T
P
L
D
B
A
IS  
U
T
T
R
R
L
S
IB  
/U  
U
N
T
IO  
B
A
N
R
1
S
A
L
M
O
N
P
A
I
U
2
P
N
R
E
N
L
B
A
IF  
IE  
P
U
L
R
T
S
B
A
L
MDA  
D
IS  
T
S
ERIE  
R
IB  
U
T
IO  
N
A
S
M
P
L
IF  
IE  
R
IR  
1
2
3
+
IN  
P
4
U
R
T
S
+
5
L
6
7
8
1
2
3
O
4
U
T
P
U
T
S
5
6
Mounting the YCV 100, VYC 100N, and VYC 100P on  
a 1U standard rack shelf  
7
8
E
N
T
E
R
P
R
E
S
E
T
M
A
A
V
V
M
A
S
S
T
R
E
R
C
IX  
I/O  
I
E
E
W
S
IT  
V
ID  
H
R
A
U
+
D
d
d
B
B
A
U
D
IO  
S
E
T
U
P
Back of the rack installation  
The YCV 100, VYC 100N, and VYC 100P can be conveniently  
mounted on the rear of a rack by using the Extron back of the  
rack mounting kit (MBB 100, Extron part #70-367-01). The back-  
of-the-rack mounting kit allows the device to be vertically  
positioned.  
Furniture mounting  
Furniture mount the YCV 100, VYC 100N, or VYC 100P using the  
optional MBU 123 mounting kit (part #70-212-01) as follows:  
1.  
Attach the two back of the rack mounting brackets to the  
sides of the unit using the four included mounting screws.  
1.  
2.  
3.  
Remove rubber feet if they were previously installed on the  
bottom of the unit.  
Attach the furniture mounting brackets to the unit with the  
machine screws provided.  
Hold the unit with the attached brackets against the  
underside of the table or other furniture. Mark the location  
of the screw holes of the bracket on the mounting surface.  
4.  
5.  
Drill 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm) deep  
in the mounting surface at the marked screw locations.  
IP  
A
T
IP  
A
Insert #8 wood screws into the four pilot holes. Tighten  
each screw into the mounting surface until just less than  
1/4" of the screw protrudes.  
6.  
Align the mounting screws with the slots in the brackets and  
place the unit against the surface, with the screws through  
the bracket slots. See the illustration below.  
IP  
A
T
IP  
A
7.  
Slide the unit slightly forward or back, then tighten all four  
screws to secure the unit in place.  
2-4  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-5  
 
Installation and Operation, cont’d  
Projector mounting  
Rear Panel Features and Cabling  
Projector mount the YCV 100, VYC 100N, or VYC 100P using the  
optional PMK 100 mounting kit (part #70-217-01) as follows:  
YCV 100  
VIDEO OUT  
YCV 100  
1.  
2.  
3.  
Remove rubber feet if they were previously installed on the  
bottom of the unit.  
S-VIDEO  
ENCODER  
2
Y
POWER  
C
Attach the projector mounting brackets to the unit with the  
machine screws provided.  
3
12V  
0.1A MAX  
OR  
S-VIDEO IN  
Secure the unit below the ceiling to a projector mount or  
other surface by inserting the mounting bolt through the  
bracket’s slotted hole, as shown below.  
4
1
Input connectors — Connect an S-video source to either:  
1
• the two female BNC connectors or  
• the 4-pin mini DIN connector.  
Projector  
Mounting  
Bracket  
Do not connect S-video sources to both types of  
connectors at the same time.  
Ceiling  
Output connector — Connect a composite video output device  
to this female BNC connector.  
2
Mounting  
Bolt  
T
U
O
O
E
ID  
V
Y
C
IN  
R
O
O
E
DI  
V
0
0
1
-
S
R
E
O
E
V
D
C
Y
DI  
V-  
O
C
S
N
E
R
E
W
O
P
X
A
M
V
2
1
A
.5  
0
Power connector — An external 12 V power supply is included  
with the unit. Plug it into this 2-pole captive screw connector.  
Wire the connector as shown below.  
3
When connecting the power supply, voltage  
polarity is extremely important. Applying power  
with incorrect voltage polarity could damage the  
power supply and the YCV 100. Identify the power  
cord negative lead by the ridges on the side of the  
cord or a black heat shrink wrapping around it.  
CAUTION  
Digital Projector  
Mounting the YCV 100, VYC 100N, and VYC 100N  
on a projector mount  
Front Panel Features  
Smooth  
Ridges  
A
A
SECTION A–A  
Power Supply  
Output Cord  
Tie Wrap  
1
3/16”  
(5 mm) Max.  
Power LED — Lights to indicate that the YCV 100/VYC 100N/  
VYC 100P is on.  
1
Orange Captive Screw  
Connector  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-6  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-7  
 
Installation and Operation, cont’d  
Strip the insulation from the wires to expose 5 mm  
(3/16") of the conductors. Do not tin the stripped power  
supply leads before installing the captive screw  
connector. Tinned wires are not as secure in the captive  
screw connectors and could be pulled out.  
Smooth  
Ridges  
A
A
SECTION A–A  
The two power cord wires must be kept separate  
while the power supply is plugged in. Remove  
power before wiring.  
Power Supply  
Output Cord  
Tie Wrap  
To verify the polarity before connection, check the no load  
power supply output with a voltmeter.  
3/16”  
(5 mm) Max.  
Power LED — Lights to indicate that the YCV 100 is on.  
4
Orange Captive Screw  
Connector  
VYC 100N and VYC 100P  
The VYC 100N and VYC 100P have identical rear panel  
connectors.  
Strip the insulation from the wires to expose 5 mm  
(3/16") of the conductors. Do not tin the stripped power  
supply leads before installing the captive screw  
connector. Tinned wires are not as secure in the captive  
screw connectors and could be pulled out.  
1
VIDEO IN  
VYC 100N  
COMPOSITE  
VIDEO  
The two power cord wires must be kept separate  
while the power supply is plugged in. Remove  
power before wiring.  
DECODER  
Y
C
POWER  
3
To verify the polarity before connection, check the no load  
power supply output with a voltmeter.  
12V  
0.5A MAX  
S-VIDEO OUT  
Power LED — Lights to indicate that the VYC 100N/VYC 100P  
4
is on.  
4
2
Input connector — Connect a composite video source to this  
female BNC connector.  
1
2
Output connectors — Connect an S-video output device to:  
• the two female BNC connectors and/or  
• the 4-pin mini DIN connector.  
Power connector — An external 12 V power supply is included  
with the unit. Plug it into this 2-pole captive screw connector.  
Wire the connector as shown in the following illustration.  
3
When connecting the power supply, voltage  
polarity is extremely important. Applying power  
with incorrect voltage polarity could damage the  
power supply and the VYC 100N/VYC 100P.  
Identify the power cord negative lead by the ridges  
on the side of the cord or a black heat shrink  
wrapping around it.  
CAUTION  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-8  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-9  
 
Installation and Operation, cont’d  
Troubleshooting  
YCV 100, VYC 100N, and VYC 100P  
Possible problems and their solutions include the following:  
Problem: No power at unit  
Solution: Verify that the unit is receiving power by  
checking the front or rear LED. If no LED is lit,  
check the DC power plug termination and  
polarity.  
Problem: No video input  
Solution: Verify that the source and output devices are  
powered on and connected properly.  
Problem: Some chroma crawl on the vertical edges or a  
rainbow effect on some images  
Solution: This is a normal characteristic of the unit.  
Appendix A  
A
Specifications, Part Numbers,  
and Accessories  
Specifications  
Included Parts  
Optional Accessories  
YCV 100, VYC 100N, VYC 100P • Installation and Operation  
2-10  
 
Specifications, Part Numbers, and Accessories  
VYC 100N ......................... NTSC 3.58  
VYC 100P .......................... PAL  
Video  
Gain ................................................ Unity  
YCV 100 ............................ NTSC 3.58, NTSC 4.43, PAL, SECAM  
Bandwidth  
YCV 100 ............................ 8 MHz (-3 dB)  
VYC 100N, VYC 100P ..... 5.5 MHz (-5.5 dB)  
General  
External power supply ................ 100 VAC to 240 VAC, 50/60 Hz, external,  
autoswitchable; to 12 VDC, 1 A (max.),  
regulated  
Video input  
Number/signal type  
YCV 100 ............................ 1 S-video  
VYC 100N, VYC 100P ..... 1 composite video  
Connectors  
YCV 100 ............................ 2 female BNC or 1 female 4-pin mini DIN  
VYC 100N, VYC 100P ..... 1 female BNC  
Nominal level ............................... 1 Vp-p for Y of S-video, and for composite  
Power input requirements  
VYC 100N, VYC 100P ..... 12 VDC, 0.2 A  
YCV 100 ............................ 12 VDC, 0.1 A  
Temperature/humidity .............. Storage: -40 to +158 °F (-40 to +70 °C) /  
10% to 90%, noncondensing  
Operating: +32 to +122 °F (0 to +50 °C) /  
10% to 90%, noncondensing  
video  
Rack mount .................................. Yes, with optional 1U, 9.5" deep rack  
shelf, part #60-190-01 (RSU 129) or  
60-604-01 (RSB 129); or VersaTools® 3.5"  
deep rack shelf, part #60-190-20 (RSF 123)  
or 60-604-21 (RSB 123)  
0.3 Vp-p for C of S-video  
Minimum/maximum levels  
S-video ............................... Analog: 0.3 V to 1.5 Vp-p for Y  
Composite video ............. Analog: 0.3 V to 1.5 Vp-p with no offset  
Impedance .................................... 75 ohms  
Return loss .................................... -35 dB @ 5 MHz  
DC offset (max. allowable) ......... 5 V  
Furniture mountable with optional mini  
under-desk mounting kit, part #70-212-01  
(MBU 123)  
Attachable to a projector mount with  
optional mounting kit, part #70-217-01  
(PMK 100)  
Video output  
Number/signal type  
Enclosure type .............................. Metal  
YCV 100 ............................ 1 composite video  
VYC 100N, VYC 100P ..... 2 S-video  
Connectors  
YCV 100 ............................ 1 female BNC  
VYC 100N, VYC 100P ..... 2 female BNCs or (1) 4-pin mini DIN  
Nominal level ............................... 1 Vp-p for Y of S-video and for composite  
Enclosure dimensions ................. 1.7" H x 2.2" W x 3.0" D  
(1U high, one eighth rack wide)  
(4.3 cm H x 5.6 cm W x 7.6 cm D)  
(Depth excludes connectors.)  
Product weight ............................. 0.4 lbs (0.2 kg)  
Shipping weight ........................... 1 lbs (1 kg)  
Vibration ....................................... ISTA 1A in carton (International Safe  
TransitAssociation)  
video  
0.3 Vp-p for C of S-video  
Listings .......................................... UL, CUL  
Compliances ................................. CE, FCC Class A, VCCI, AS/NZS, ICES  
MTBF ............................................. 30,000 hours  
Minimum/maximum levels ....... 0.3 V to 1.5 Vp-p for Y of S-video or  
composite video (follows input)  
Impedance .................................... 75 ohms  
Return loss .................................... -40 dB @ 5 MHz  
Warranty ....................................... 3 years parts and labor  
DC offset ....................................... 5 mV maximum with input at 0 offset  
All nominal levels are at 10%.  
Sync  
Standards  
Specificationsaresubjecttochangewithoutnotice.  
YCV 100, VYC 100N, VYC 100P • Specifications and Parts  
YCV 100, VYC 100N, VYC 100P • Specifications and Parts  
A-2  
A-3  
 
Specifications, Part Numbers, Accessories, cont’d  
Included Parts  
These items are included in each order for a YCV 100,  
VYC 100N, or VYC 100P:  
Replacement  
part number  
Included parts  
YCV 100  
60-559-01  
60-558-02  
60-558-03  
70-055-01  
or VYC 100N  
or  
VYC 100P  
12 VDC, 1 A external power supply  
IEC power cord  
3.5 mm, 2-pole captive screw connector  
Tweeker (small screwdriver)  
User’s Manual  
Optional Accessories  
These items can be ordered separately:  
Accessories  
Part number  
Mini under-desk mounting bracket  
Mini projector mounting bracket  
1U universal rack shelf kit  
70-212-01  
70-217-01  
60-190-01  
60-604-02  
60-190-10  
60-604-11  
60-190-20  
60-604-21  
70-367-01  
1U basic rack shelf  
1U 6" deep universal rack shelf kit  
1U 6" deep basic rack shelf  
VersaTools rack shelf kit  
VersaTools basic rack shelf  
VersaTools back-of-the-rack mounting kit  
YCV 100, VYC 100N, VYC 100P • Specifications and Parts  
A-4  
 

EDGE Tech Computer Drive 3126 User Manual
Eiki Network Card EZ WDVA User Manual
Eiki Projector EIP 250 User Manual
Eizo Computer Monitor L771 User Manual
Eton Radio FR400 User Manual
Fluke Thermometer 1504 User Manual
Gap Nail Gun N75C User Manual
Garland Fryer S18 FS User Manual
Gemini CD Player CDX 01 User Manual
GE Telephone SoundStation2 User Manual