Earthquake Sound Speaker SWS 10X 4 OHM User Manual

Sound That Will Move You  
US PATENT # 6,675,931 B2  
S H A L L O W  
W O O F E R  
S Y S T E M  
SWS-6.5X (4-Ohm)  
SWS-8X (4-Ohm)  
SWS-8Xi (2-Ohm)  
SWS-10X (4-Ohm)  
SWS-12X (4-Ohm)  
SWS-15X (4-Ohm)  
Installation Reference Guide  
The Sound That Will Move You.  
Earthquake Sound reserves the right to amend details of the specifications without notice.  
Copyright © Earthquake Sound Corporation  
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545  
Phone: 510-732-1000 Fax: 510-732-1095  
 
SPECIFICATIONS  
SWS Enclosures  
SWS subwoofers are designed to bring bass virtually anywhere in a car: in front doors,  
rear doors, dash board, center console, under seats, rear decks, and in any space limited  
mounting depth. The following volumes shown below are created to give you optimized  
"deep bass from the shallowest space".  
Actual RMS power varies based on box design and on music played  
SWS-15X  
• Speaker diameter = 15"  
• Mounting depth = 3 1/4"  
• Cut out mounting hole = 13 3/4"  
• Weight = 15Lbs  
(81mm)  
(3 1/4")  
In order to match a box volume that bests suites your needs, you will need to find out the  
amount of space that you have to work with, then use the formula below to find out which  
range you will should be in based on our recommendations.  
• Voice Coil diameter = 2.5"  
• Aluminum bobbin / wire  
• Power rating RMS = 400W  
• Power rating MAX = 800W  
• Revc = 3.76 Ohms  
(350mm / 13 3/4")  
(cut out hole diameter)  
Choosing an enclosure type that perfectly tailors to your needs can sometimes be a hassle  
and unfortunately choosing or building the wrong enclosure could potentially destroy the  
sound quality of your system. The SWS subwoofers deliver truly prenominal bass response  
from the shallowest of places. And in order to harness their greatness you will need to  
make sure that your enclosure will be suffice for your application.  
Actual RMS power varies based on box design and on music played  
SWS-12X  
• Speaker diameter = 12"  
• Mounting depth = 3"  
Sealed Enclosures:  
• Cut out mounting hole = 11 3/8"  
• Weight = 13Lbs  
(75mm)  
(3")  
Do you often turn the bass down on a car or home stereo system because it sounds boomy  
to you? If you do, a sealed enclosure is an excellent choice, especially if you listen to a  
wide variety of music. This type of enclosure produces well-defined, strong, but not  
overpowering bass.  
• Voice Coil diameter = 2.5"  
• Aluminum bobbin  
• Power rating RMS = 300W  
• Power rating MAX = 600W  
• Revc = 3.76 Ohms  
(288mm / 11 3/8")  
(cut out hole diameter)  
Bandpass Enclosures:  
This bass is not really punchy, it's more like a massive, swampy force of low end that  
powers the music which can be great for some tunes and extremely overwhelming on  
others. If you prefer the harder stuff (metal, hard rock, industrial) or music with impact bass  
content (reggae, hip hop) and you like your bass to be LOUD, the bandpass box is a great  
way to go. And, if your amplifier is lacking in the power department, you'll get the most bang  
for your buck from this design.  
Actual RMS power varies based on box design and on music played  
SWS-10X  
• Speaker diameter = 10"  
• Mounting depth = 2 11/16"  
• Cut out mounting hole = 9"  
• Weight = 11Lbs  
• Voice Coil diameter = 2"  
• Aluminum bobbin  
• Power rating RMS = 200W  
• Power rating MAX = 400W  
• Revc = 3.76 Ohms  
(68mm)  
(2 11/16")  
Ported Enclosure:  
The ported box is also exceptionally loud, so it will also be a good choice if you have limited  
power available. If you listen to a wide range of music and if you're always cranking up the  
bass when you listen to tunes.  
(228mm / 9")  
(cut out hole diameter)  
Actual RMS power varies based on box design and on music played  
SWS-8X/8Xi  
• Speaker diameter = 8"  
• Mounting depth = 2 1/8"  
CAUTION:  
Earthquake Subwofoers are capable of generating high sound pressure  
levels. You should exercise caution when operating these  
subwoofer/amplifier systems. Long term exposures to high levels of sound  
CAUTION:  
THE 2-OHM SWS-8XI  
(52mm)  
(2 1/8")  
• Cut out mounting hole = 7 7/8" IS FOR FACTORY  
pressure will cause permanent damage to your hearing. Sound pressure levels exceeding  
85dB can be dangerous with constant exposure. Set your audio system to a comfortable  
loudness level. Earthquake Sound Corporation does not assume liability for damages  
resulting from the direct use of Earthquake amplifiers or other Earthquake products , and  
urges users toplay their music at moderate listening levels.  
UPGRADED VEHICLES  
• Weight = 8 Lbs  
• Voice Coil diameter = 1.5"  
• Aluminum bobbin  
ONLY  
(206mm / 8- 1/8")  
(cut out hole diameter)  
• Power rating RMS = 150W  
• Power rating MAX = 300W  
Revc = 8=3.76 Ohms / 8Xi=1.76 Ohms  
SOUND LEVEL DBA  
DURATION IN HOURS  
THE CHART (ON THE SIDE)  
S H O W S T H E U . S .  
Actual RMS power varies based on box design and on music played  
90  
92  
95  
8
6
4
3
2
G
O
V
E
R
N
M
E
N
T
S
SWS-6.5X  
OCCUPATIONAL SAFETY AND  
HEA LTH A DMINISTRATION  
(OSHA) REGULATIONS WHICH  
WERE IN EFFECT AT THE TIME  
OF THIS PUBLICATION FOR  
• Speaker diameter = 6.5"  
• Mounting depth = 1 3/4"  
• Cut out mounting hole = 5 3/4"  
• Weight = 5 Lbs  
• Voice Coil diameter = 1"  
• Aluminum bobbin  
• Power rating RMS = 100W  
• Power rating MAX = 200W  
• Revc = 3.6 Ohms  
(45mm)  
(1 3/4")  
97  
100  
102  
105  
110  
115  
1 - 1 1/2  
1
1/2  
(142mm / 5 3/4")  
(cut out hole diameter)  
P E R M I S S I B L E  
N O I S E  
EXPOSURE, PER 29CFR1910.95,  
TABLEG-16.  
1/4 or l es s  
All Specifications Are Subject To Change Without Notice  
4
5
 
Calculating Enclosure Dimensions  
Examples Of Limited Space Applications  
Finding Box Dimensions For Recommended Enclosure Volumes:  
To find the volume best suited for you, you will need to measure the max and min Height,  
Width and Depth of the area where you to plan to place the sub-enclosure. Then subtract  
1.5" each dim to get the internal dims. Now use the internal H, W & D in the formula below  
to match your dims with one of our recommended ranges.  
Enclosure;  
Made With 3/4" Medium  
Density MDF  
D
W
Volume  
H
External Dims:  
H=10 x W=10 x D=5  
Internal Dims:  
H=8.5 x W=8.5 x D=3.5  
To Get The Internal Dims Simply Subtract  
The Total Thickness Of The MDF From The  
External Dims;  
Which With 3/4" MDF Is 1-1/2"  
FORMULA  
8.5 x 8.5 x 3.5 + 1728 = 0.15cu.ft.  
CAUTION: In some cases when the enclosure will be placed with the sub facing down or  
the sub butted up against the back of seat (like the illustration). You will need to either add  
a grille or use 1" strips of your MDF and place as shown above. This will create an  
excursion cushion so that it doesn't rub or get damaged.  
All Specifications Are Subject To Change Without Notice  
6
7
 
SWS-6.5 Recommended Applications  
Example Minimum Sealed Designs (8,10,12 & 15" Models)  
The SWS 6.5 woofer is designed to replace any stock / factory installed 6.5" driver. It  
brings bass virtually anywhere in a car: in front doors, rear doors, dash board, center  
console, under seats, rear decks, and in any space less than 2" deep.  
SWS-8/8Xi Minimum Sealed Example  
11-1/2"  
17-1/2"  
19-1/2"  
21-1/2"  
External Dimensions: 11" x 11-1/2" x 5"  
Internal Dimensions: 10" x 9" x 3-1/2"  
Internal Volume: 0.19cu.ft. (5.44Ltr.)  
5"  
5-1/2"  
5-1/2"  
8"  
Recommended Sealed Internal Volume (8,10,12 & 15" Models)  
11"  
0.19cu.ft. (5.44Ltr)  
0.60cu.ft. (16.99Ltr)  
Minimum:  
Maximum:  
SWS-8/8Xi  
SWS-8/8Xi  
0.38cu.ft. (10.76Ltr)  
0.75cu.ft. (21.23Ltr)  
Minimum:  
Maximum:  
SWS-10X  
SWS-10X  
SWS-10X Minimum Sealed Example  
External Dimensions: 12" x 17-1/2" x 5.5"  
Internal Dimensions: 12" x 16" x 4"  
Internal Volume: 0.38cu.ft. (10.76Ltr.)  
0.56cu.ft. (15.85Ltr)  
1.25cu.ft. (35.39Ltr)  
Minimum:  
Maximum:  
SWS-12X  
SWS-12X  
1.20cu.ft. (33.98Ltr)  
2.5cu.ft. (70.79Ltr)  
Minimum:  
Maximum:  
12"  
SWS-15X  
SWS-15X  
Our Examples and Reccomendations Are Calculated Assuming That 3/4" MDF Is Being Used  
3/4"  
MDF  
SWS-12X Minimum Sealed Example  
External Dimensions: 15" x 19-1/2" x 5-1/2"  
Internal Dimensions: 13-1/2" x 18" x 4"  
Internal Volume: 0.56cu.ft. (15.85Ltr.)  
In some cases when the enclosure will be placed with  
the sub facing down or the sub butted up against the back  
of seat. You will need to either add a grille or use 1" strips of  
your MDF and place as shown above. This will create an  
excursion cushion so that it doesn't rub or get damaged.  
15"  
1" - 1.5" Depending On The Woofer  
SWS-15X Minimum Sealed Example  
External Dimensions: 17-1/2" x 21-1/2" x 8"  
Internal Dimensions: 16" x 20" x 6-1/2"  
Internal Volume: 1.20cu.ft. (33.98Ltr.)  
One Subwoofer  
Two Subwoofers  
17-1/2"  
SWS subwoofers will handle crazy amounts of power in any of the recommended enclosures,  
minimum or maximum. The compact enclosures are best for use in limited-space applications.  
The larger recommended enclosures will deliver  
frequencies ranges.  
a
bit more bass at the lowest  
All Specifications Are Subject To Change Without Notice  
8
9
 
EARTHQUAKE 5 YEAR LIMITED WARRANTY  
Regarding Your Warranty:  
(D) Warranty Limitations:  
Warranty does not cover products that have been modified or abused. Including  
but not limited to the following:  
• Damages to speaker cabinet and cabinet finish due to misuse, abuse, or use of improper  
use of cleaning materials/methods.  
Thank you for choosing Earthquake Sound’s line of SWS subwoofers for superior  
enhancement of your vehicle’s audio system from any location. With proper installation and  
responsible listening, your SWS subs will give you years of phenomenal listening  
enjoyment.  
• Bent speaker frame, broken speaker connectors, holes in speaker cone, surround & dust  
cap, burnt speaker voice coil.  
• Fading, deterioration of speaker components & finish due to improper exposure to  
elements.  
• Bent amplifier casing, damaged finish on the casing due to abuse, misuse, or improper  
use of cleaning material.  
• Burnt tracers on PCB.  
We strongly recommend you to have your new SWS subs installed by an authorized  
Earthquake Sound dealer: Installation professionals employed by your dealer have the  
correct tools and knowledge to install your speakers neatly and successfully. Also, when  
your new products are installed by an authorized dealer, your product will include a FIVE  
YEAR LIMITED WARRANTY. If you choose to perform your own installation, your warranty  
will be subject to limitations. Over the counter authorized dealer warranties may very from  
one dealer to the next. Please read the warranty information in its entirety and use good  
judgment when making these vital decisions.  
• Product/part damaged due to poor packaging or abusive shipping conditions.  
• Subsequent damage to other products.  
A warranty claim will not be valid if the warranty registration card is not  
properly filled & returned to Earthquake with a copy of the sales invoice.  
Five (5) year limited warranty:  
(E) Service Request:  
Earthquake warrants the original purchaser that all Factory Sealed New Audio  
Products be free from defects in material and workmanship under normal and proper use  
for a period of five (5) years from the date of purchase (as shown on the original bill of sale  
with serial number affixed/written on it). The five (5) year warranty period is valid only if an  
authorized Earthquake dealer properly installs the product and the warranty registration  
card is properly filled out and sent to Earthquake Sound Corporation. If a non-authorized  
party installs the product a ninety (90) day warranty period will be applied.  
To receive product/s service, contact Earthquake service department at (510)  
732-1000 and request an RMAnumber (Return MaterialAuthorization), items shipped without  
a valid RMA number will be refused. Make sure you provide us with your complete/correct  
shipping address, a valid phone number, and a brief description of the problem you are  
experiencing with the product. In most cases, our technicians might be able to resolve the  
problem over the phone, thus eliminating the need toship the product.  
(F) Shipping Instructions:  
(A) Five (5) years limited warranty plan coverage guidelines:  
Product/s must be packaged in its original protective box(s) to minimize  
transport damage. Shipper claims regarding items damaged in transit must be presented to  
carrier. Earthquake Sound Corporation reserves the right to refuse product improperly packed.  
Original bill of sale must accompany product returned for service. We encourage you to include  
with the package a written description of the problem. Ship product to: Earthquake Sound  
Corp. 2727 Mc ConeAvenue, Hayward, CA94545. Ph (510) 732-1000. You are responsible for  
the cost of shipping the product toEarthquake Sound Corporation.  
• First year: Earthquake pays for labor, parts, and ground freight (only in US mainland, not  
including Alaska and Hawaii).  
• Second year: Earthquake pays for labor and parts only, customer must pay freight both  
ways.  
• Third, fourth & fifth year: Earthquake pays labor only. Customer must pay for parts and  
freight both ways.  
(B) Warning:  
(G) Disputes Resolution:  
Products (sent for repair) that are tested by Earthquake technicians and deemed  
to have no problem(s) will not be covered by the five (5) year limited warranty. Customer  
will be charged a minimum of one (1) hour of labor (ongoing rates) plus shipping charges  
back to customer.  
All disputes - between clients and Earthquake Sound Corporation - resulting  
from the five (5) years limited warranty policy must be resolved according to the laws &  
regulations of the county ofAlameda -California.  
(C) Earthquake will repair or replace - at our option - all defective products/parts  
subject to the following provisions:  
• Defective products/parts have not been altered or repaired by other than an Earthquake  
factory approved technician.  
• Products/parts are not subjected to negligence, misuse, improper use, or accident,  
damaged by improper line voltage, used with incompatible products, or have its serial  
number or any part of it altered, defaced or removed, or have been used in any way that  
is contrary to Earthquake's written instructions.  
Alternatively you may register your products online at  
Warranty Continued On Next Page  
All Specifications Are Subject To Change Without Notice  
10  
11  
 

Electro Voice Microphone 660A User Manual
Extron electronic Switch 450 Plus User Manual
Extron electronic Universal Remote KP 6 User Manual
Extron electronic Universal Remote UCM 10X8P User Manual
Fitness Quest Home Gym NBP01075 2 User Manual
Focal Car Speaker SB 27 V1 User Manual
FOCUS Enhancements Camcorder FS 2 User Manual
Fujitsu Scanner fi 5120C User Manual
Fujitsu Tablet T4220 User Manual
Giant Septic System LP700 User Manual