Fisher Price Motorized Toy Car 72607 User Manual

Instructions  
Jeep  
®
Pushn Scoot  
Model Number: 72607  
If you experience a problem with this product, or are missing a part,  
please call us at 1-800-432-KIDS, rather than return this product to the store.  
Please save these instructions for future reference.  
Adult assembly is required.  
Tools required for assembly: Hammer and Scrap Block of Wood.  
Weight Limit: 55 lbs.  
1
2
Ages: 1 / years - 5 years.  
 
Assembly  
3
CAUTION  
Please keep small parts and plastic  
bags out of children’s reach. Dispose of  
plastic bags properly.  
1
Vehicle  
Body  
Rear Axle  
Spacer  
Rear Axle  
Cap Nut  
• Insert the rear axle through the holes in the rear of the  
vehicle body. Make sure the spacer fits into the hole in  
the vehicle body.  
Scrap Block  
of Wood  
4
Spacer  
• Place a cap nut on a scrap block of wood.  
• Fit the rear axle into the cap nut and tap with a hammer  
until secure.  
Rear Axle  
Vehicle Body  
2
Rear Axle  
Spacer  
Wheel  
Wheel  
Scrap Block of Wood  
Cap Nut Tool  
Spoke Side Down  
Turn the vehicle body on its side with the end of the  
rear axle facing up.  
• Lift the vehicle body up slightly and fit a cap nut tool on  
the cap nut.  
• Slide a block of wood under the cap nut tool to support  
the rear axle.  
• Slide a wheel, spoke side down, onto the rear axle.  
• Slide a spacer onto the rear axle.  
• Fit the other spacer onto the rear axle and into the hole  
in the vehicle body.  
3
 
Assembly  
5
7
Bushing  
Cap Nut  
Cap Nut Tool  
Rear Axle  
Spoke Side Up  
"A" Front Axle  
Bushing  
Wheel  
Washer  
• Slide a washer onto the "A" front axle.  
• Slide a bushing, narrow side up, onto the "A" front axle.  
• Repeat steps 6 and 7 to assemble the "B" front  
axle, washer, wheel, bushing and cap nut.  
• Slide a wheel, spoke side up, onto the end of the  
rear axle.  
• Fit a cap nut onto the end of the rear axle.  
• Fit a cap nut tool over the cap nut and tap the center  
with a hammer until the cap nut is secure.  
8
Vehicle  
Body  
"A" Marking  
"A"  
Front  
Axle  
6
Cap Nut  
Tool  
B
A
Cap Nut  
Bushing  
Wheel  
Spoke Side Up  
"A"  
Front  
Axle  
Turn the vehicle body upright.  
• Lift the front end of the vehicle body and locate the  
side of the vehicle body marked "A".  
IMPORTANT! For proper wheel position, the "A" front  
axle assembly must be inserted into the hole in the  
vehicle body marked "A".  
• Insert the "A" front axle up into the hole underneath  
the vehicle body marked "A".  
Scrap  
Block of  
Wood  
"A" Front "B" Front  
Axle Axle  
Washer  
• Identify and separate the "A" and "B" front axles.  
• Place the "A" front axle onto a scrap block of wood.  
• Slide a washer onto the "A" front axle.  
• Slide one of the wheels, spoke side up, onto the "A"  
front axle.  
• Make sure the bushing fits into the hole in the vehicle  
body.  
• Fit a cap nut onto the end of the "A" front axle.  
4
• Fit a cap nut tool over the cap nut and tap the center  
with a hammer until the cap nDuotwisnlosaedcfruorme.Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
9
Cap Nut Tool  
Cap Nut  
Bushing  
Bushing  
"A"  
Front  
Axle  
2
1
Vehicle Body  
10  
9
• Lower the vehicle body.  
• Fit a bushing, narrow side down, onto the exposed end  
of the "A" front axle and into the hole in the vehicle  
body.  
Front View  
• Fit a cap nut onto the end of the "A" front axle.  
• Fit a cap nut tool over the cap nut and tap the center  
with a hammer until the cap nut is secure.  
9
• Repeat assembly steps 8 and  
to assemble the  
"B" front axle to the side of the vehicle body marked "B".  
• Dispose of the cap nut tools properly.  
8
7
10  
4
Handle  
3
6
5
Hole  
Back View  
• Make sure the areas where the labels will be applied  
are clean and dry.  
Hole  
• Apply the labels as shown in the illustrations.  
• For best adhesion, try to avoid applying a label more  
than once.  
Rear of  
Vehicle  
Body  
One-time assembly is now complete.  
• Position the handle over the rear of the vehicle body so  
that it leans away from the vehicle body.  
• While keeping the vehicle body stationary, insert and  
snap the handle into the two holes in the rear of the  
vehicle body.  
5
 
Use  
Three (3) Year Limited Warranty  
Fisher-Price, Inc., 636 Girard Avenue, East Aurora,  
New York 14052, warrants to the original owner that the  
Jeep Push 'n Scoot™ is free from all defects in material  
and ®workmanship when used under normal conditions for  
a period of three (3) years from the date of purchase. This  
warranty does not cover color fading of the product or  
product parts, or damage from excessive abuse or Acts  
of God.  
When pushing your child in the Jeep Push 'n Scoot™,  
®
use the pull-out footrest.  
Footrest  
Notches  
Should the product fail to perform properly, we will repair  
or replace it, free of charge. Purchaser is responsible for  
shipping the product to the address indicated above and  
for all associated freight and/or insurance cost.  
Tab  
Tab  
Fisher-Price, Inc. will bear the cost of shipping the repaired  
or replaced item to you. This warranty is void if the owner  
repairs or modifies the product. This warranty excludes any  
liability other than the above mentioned, including but not  
limited to any incidental or consequential damages.  
Seat  
SOME STATES DO NOT ALLOW THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL  
DAMAGES, SO THE ABOVE LIMITATION OR EXCLU-  
SION MAY NOT APPLY TO YOU.  
• Pull the footrest out from under the seat.  
• Hook the notches in the front of the footrest onto the  
tabs on the inside front of the Jeep Push 'n Scoot™.  
®
THIS WARRANTY GIVES YOU SPECIFIC LEGAL  
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH MAY VARY FROM STATE TO STATE.  
Maintenance  
• Periodically check the Jeep Push 'n Scoot™ to be sure  
all fasteners are secure and re-fasten as needed.  
To clean or remove static electricity, use a mild soap  
and water solution and a clean cloth. Rinse clean with  
water to remove soap residue.  
®
Questions?  
We'd like to hear from you!  
Call Fisher-Price® Consumer Affairs, toll-free at  
1-800-432-KIDS, 8 AM - 6 PM EST Monday through  
Friday. Hearing-impaired consumers using TTY/TDD  
equipment, please call 1-800-382-7470. Or, write to:  
Fisher-Price® Consumer Affairs, 636 Girard Avenue,  
East Aurora, New York 14052.  
JEEP and Jeep grille design are registered trademarks of Chrysler Corporation U.S.A. Used under license.  
© CHRYSLER CORPORATION 1997.  
If you have any questions about this product:  
In Canada, call 1-800-567-7724, or write to: Mattel/Fisher-Price, 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.  
In Great Britain, telephone 01734 770488.  
In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to: Fisher-Price, Mattel Pty. Limited, 461 Plummer Street,  
Port Melbourne, Victoria 3207.  
©1997 Fisher-Price, Inc., East Aurora, New York 14052  
Printed in U.S.A.  
72607 1 72607-0920  
 

Conair Hair Clippers HC701 User Manual
Connect Tech Network Card Multi port Serial Adapter User Manual
Cooper Lighting Work Light L1510 User Manual
Craftsman Snow Blower 536881851 User Manual
DuPont Authentication Insect Control Equipment H 65190 User Manual
Electro Voice Microphone N D308 User Manual
Escient Home Theater System SE D1 User Manual
Fisher Metal Detector GEMINI 3 User Manual
Garland Cooktop BH IN 2500 User Manual
GE Washer Dryer WSM2480T User Manual