EverFocus Security Camera ED640 User Manual

Indoor DWDR 3-Axis Varifocal  
700TVL IR Dome Camera  
Operation Instructions  
Model No. ED640  
Please read this manual first for correct installation and operation. This manual should be  
retained for future reference. The information in this manual was current when published.  
The manufacturer reserves the right to revise and improve its products. All specifications are  
therefore subject to change without notice.  
PRECAUTIONS  
1. Do not install the camera near electric or magnetic fields.  
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and  
audio speakers since the electromagnetic fields generated from these devices may distort the  
video image or otherwise interfere with camera operation.  
2. Never disassemble the camera beyond the recommendations in this manual nor introduce  
materials other than those recommended herein. Improper disassembly or introduction of  
corrosive materials may result in equipment failure or other damage.  
3. Try to avoid facing the camera toward the sun.  
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or  
internal circuits, as well as creating unbalanced illumination beyond the capability of the camera  
to compensate.  
4. Keep the power cord away from water and other liquids and never touch the power cord  
with wet hands. Touching a wet power cord with your hands or touching the power cord with  
wet hands may result in electric shock.  
5. Never install the camera in areas exposed to oil, gas or solvents.  
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.  
6. Cleaning  
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with the  
hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the  
camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do not use  
complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.  
7. Do not operate the camera beyond the specified temperature, humidity or power source  
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures within  
-10° ~ +50° (14 ~122 ) and humidity between 30% and 90%. The input power source is  
12VDC. Regulated power supply required.  
 
Specifications  
TV System  
NTSC  
1/3” Sony Super HAD II Color CCD  
768Hx494V  
Image Sensor  
Effective Pixels  
Resolution  
700 TV Lines  
Lens  
2.8~12mm VF AI  
Scanning System  
Scanning Frequency  
Auto Shutter Speed  
Sync. System  
S/N Raito  
525Lines, 2:1Interlace  
15.734KHz(H),59.94Hz  
1/60 to 1/100,000sec.  
Internal  
More than 52dB (AGC off)  
5 Button Navigation. Multiple options  
OSD  
English, Spanish, French, Portuguese,  
German, Polish, Japanese, Chinese  
Auto/Color Black & White;  
OSD Language  
Day & Night  
Digital Day/Night with programmable switch levels and delays  
Min. Illumination  
IR LEDs  
0.01 lux nominal; 0 lux with IR LEDs on  
24 smart LEDs, 850nm  
IR Range  
82 feet (depends on scene IR reflectivity)  
Off/On with programmable area of interest and gain  
Off, Low, Middle, High  
Smart IR Control  
Auto Gain Control  
DWDR  
Off/On with adjustable weight  
Off/On for two areas with programmable  
area of interest and gain  
BLC  
BLC/HLC  
HLC  
Off/Night Only/Always with adjustable level  
0.45; Display compensation option for CRT or LCD with  
adjustable levels  
Gamma Correction  
DNR  
2D DNR Off/On  
Lens Shading  
Compensation  
Off/On, adjustable for level and image center  
Mirror  
Off/On  
Off/On  
Negative Image  
White Balance  
Digital Pixel Correction  
AWB ( 2,100˚k ~ 9,100˚k)  
Manual operation; programmable threshold and area  
3
 
Motion Detection  
Privacy Zones  
Video Output  
On screen indication; up to 4 programmable areas  
Up to 8areas programmable for location and color  
NTSC CVBS, 1Vp-p, 75  
DC 12V 10%  
Power Supply  
Power Consumption  
Operating Temperature  
Storage Temperature  
Operating Humidity  
Dimension  
160mA Nominal / 320mA IR ON  
14ºF ~ 122ºF ; -10°C~50°C  
-4ºF ~ 140ºF ; -20°C~60°C  
to 90% RH max.  
4.41”/112mm diameter, 3.43”/87mm high  
7.2oz/205g  
Weight  
Certifications  
CE/FCC  
Dimensions  
Mounting holes  
1.77” radius  
3 places  
4
 
Installation  
Warning: To prevent electrical shock, turn off the electrical power before making electrical  
connections. OBSERVE POLARITY when connecting 12VDC power to the camera.  
1. Select mounting location. Open cover using tool provided.  
2. Place template and drill holes (5/8” minimum for wires, ~¼” for hollow wall anchors; ~3/32” pilot  
hole for screws alone). Insert wall anchors if used.  
3. Mount camera to ceiling with 3 screws and adjust camera direction.  
4. Replace dome cover on base (snaps on).  
1
2.  
3.  
4.  
OSD Menu Controls and Video Test Point  
Press the Menu/Enter button to bring up the OSD  
menu. Navigate the menu with the direction keys.  
Select RETURN to move back to the previous level  
menu. When exiting the main menu, choose SAVE,  
NOT SAVE or RESET (factory defaults) as desired.  
Use adapter cable supplied to connect test monitor to  
video test point.  
Lens Adjustment  
Use fingers or screwdriver to adjust field of view (zoom)  
and focus.  
5
 
Menu Setting (Default values shown in parentheses).  
(Rev. 1.1)  
MENU  
SUB MENU AND FACTORY SETTING PARAMETERS  
BRIGHTNESS  
IRIS SPEED  
0 ~ 255  
0 ~ 15  
(50)  
(5)  
DC  
LENS  
(DC)  
MANUAL  
SHUTTER  
BRIGHTNESS  
0 ~ 255  
(50)  
AUTO, 1/60(50), FLK, 1/250, 1/500, 1/1000, 1/2000,  
1/4000, 1/5000, 1/10000, 1/100000  
(1/60)  
(MIDDLE)  
(32)  
EXPOSURE  
AGC  
OFF, LOW, MIDDLE, HIGH  
DWDR (OFF) LEVEL  
ATW1  
0 ~63  
ATW2  
AWCSET  
ANTI.CRL  
WHITE BAL  
(ATW1)  
COLOR TEMP  
MANUAL, INDOOR, OUTDOOR  
MANUAL  
(OFF)  
BLUE (MANUAL) 0 ~ 255  
(65)  
(26)  
RED (MANUAL)  
0 ~ 255  
AREA SEL.  
AREA STATE  
GAIN  
AREA1, AREA2  
ON, OFF  
0 ~ 255  
0 ~ 10  
(128)  
(005)  
(005)  
(005)  
(005)  
(177)  
BLC  
HLC  
HEIGHT  
BACKLIGHT  
(OFF)  
WIDTH  
0 ~ 10  
LEFT/RIGHT  
TOP/BOTTOM  
D=>N LEVEL  
0 ~ 15  
0 ~ 15  
0 ~ 255  
NIGHT ONLY, ALL DAY  
ONLY)  
(NIGHT  
MODE  
MASK SKIP  
OFF, ON  
160~255  
1 ~ 30  
0 ~ 64  
0 ~ 30  
(OFF)  
D=>N LEVEL  
D--N DELAY  
N=> D LEVEL  
N--D DELAY  
(192)  
(1) SEC  
(032)  
AUTO  
(5) SEC  
COLOR  
BURST  
ON,OFF  
ON, OFF  
IR GAIN  
HEIGHT  
WIDTH  
(OFF)  
(ON)  
0 ~ 255  
0 ~ 015  
0 ~ 015  
DAYNIGHT  
(AUTO)  
(122)  
(006)  
(010)  
B/W  
IR SMART  
LEFT/RIGHT  
0 ~ 015  
(002)  
TOP/DOWN  
HIGH, LOW  
0 ~ 015  
(007)  
IR LEVEL  
(HIGH)  
6
 
MENU  
SUB MENU AND DEFAULT SETTING  
D=>N DELAY  
N=>D DELAY  
0 ~ 30  
0 ~ 30  
(1)  
(1)  
DAYNIGHT  
(AUTO)  
EXT  
START  
(Cover the lens then press enter key) Process now  
DPC VIEW  
LS VALUE  
DIFF.  
OFF, ON  
0 ~ 63  
(OFF)  
(015)  
(010)  
(021)  
(255)  
(008)  
(118)  
(ON)  
0 ~ 63  
DPC  
AREA HS  
AREA HE  
AREA VS  
AREA VE  
CAM TITLE  
0 ~ 255  
0 ~ 255  
0 ~ 255  
0 ~ 255  
OFF, ON  
AREA  
1~4  
(AREA1)  
AREA STATE  
HEIGHT  
WIDTH  
LEFT/RIGHT  
TOP/BOTTOM  
DEGREE  
VIEW  
ON,OFF  
0~15  
0~15  
0~15  
0~15  
0~255  
ON,OFF  
1~8  
(OFF)  
(4)  
(4)  
(3)  
(2)  
(32)  
(ON)  
(1)  
MOTION  
(OFF)  
SPECIAL  
AREA  
PRIVACY  
(OFF)  
AREA STATE  
ON,OFF  
(ON)  
HEIGHT  
0 ~ 125  
0 ~ 215  
0 ~ 220  
0 ~ 105  
0~15  
(032)  
(032)  
(032)  
(016)  
(014)  
WIDTH  
PRIVACY  
LEFT/RIGHT  
TOP/BOTTOM  
COLOR  
SPECIAL  
LEVEL  
0~255  
(157)  
(074)  
(053)  
H-CENTER  
V-CENTER  
ON, OFF  
ON, OFF  
FONT  
0~255  
0~255  
LENS SHAD. (OFF)  
IMAGE ADJ.  
2DNR  
(ON)  
(OFF)  
MIRROR  
0 ~ 15 (003)  
0 ~ 15 (003)  
(137)  
FONT COLOR  
ID & TITLE  
0 ~ 255  
0 ~ 31  
CONTRAST  
SHARPNESS  
(016)  
7
 
MENU  
SUB MENU AND DEFAULT SETTING  
PED LEVEL  
0~63  
(028)  
0~255  
(192)  
0.3~1.0  
(0.55)  
0~63  
(028)  
0~255  
(192)  
0.3~1.0  
(0.45)  
0~63  
(028)  
0~255  
(176)  
CRT  
COLOR  
GAIN  
GAMMA  
DISPLAY  
PED LEVEL  
LCD  
COLOR  
GAIN  
GAMMA  
PED LEVEL  
USER  
DISPLAY  
IMAGE ADJ.  
COLOR  
GAIN  
SPECIAL  
NEG.IMAGE  
ON, OFF  
(OFF)  
LANGUAGE  
(ENGLISH)  
ENGLISH,CHINESE1, ESPANOL, POLISH, DEUTSCH,  
PORTU FRANCAIS,JAPANESE  
VERSION  
00 00 00  
EXIT  
SAVE, NOT SAVE, RESET  
*Depending on setting of sub menu, the default value may be changed.  
8
 
EverFocus Electronics Corp.  
Corporate Headquarters:  
12F, No.79 Sec. 1 Shin-Tai Wu Road,  
Hsi-Chih, Taipei, Taiwan  
TEL: +886-2-26982334  
FAX: +886-2-26982380  
China Office:  
Room 609, Technology Trade Building,  
Shangdi Information Industry Base,  
Haidian District, Beijing, China 100085  
TEL: +86-10-62973336~39  
FAX: +86-10-62971423  
U.S.A - California Office:  
1801 Highland Avenue Units A & B  
Duarte, CA 91010  
TEL: +1-626-844-8888  
FAX: +1-626-844-8838  
U.S.A - New York Office:  
415 Oser Avenue Unit S  
Happauge, NY 11788  
TEL: +1-631-436-5070  
FAX: +1-631-436-5027  
Europe - Germany Office:  
Albert-Einstein-Strasse 1,  
D-46446 Emmerich, Germany  
TEL: +49-2822-93940  
FAX: +49-2822-939495  
Japan Office:  
5F Kinshicho city Building,  
2-13-4 Koto-Bashi,  
Sumida-Ku, Tokyo, 130-0022 Japan  
TEL: +81-3-5625-8188  
FAX: +81-3-5625-8189  
India Office:  
UK Office:  
Unit 12 Spitfire Business Park  
Hawker Road  
Croydon, CR0 4WD  
London: 0845 430 9999  
Telford: 0845 430 8888  
Fax: 020 8649 9907  
Suite 803, Housefin Bhavan, C-21,  
Bandra Kurla Complex, Bandra (East),  
Mumbai 400051. India.  
TEL: +91-222-444-8791  
FAX: +91-222-444-8790  
Your EverFocus product is designed and  
manufactured with high quality materials and  
components which can be recycled and reused.  
This symbol means that electrical and  
electronic equipment, at their end-of-life,  
should be disposed of separately from your  
household waste.  
Please, dispose of this equipment at your local  
community waste collection/recycling centre.  
In the European Union there are separate  
collection systems for used electrical and  
electronic product.  
Please, help us to conserve the environment  
we live in!  
Ihr EverFocus Produkt wurde entwickelt und  
hergestellt  
mit  
qualitativ  
hochwertigen  
Materialien und Komponenten, die recycelt und  
wieder verwendet werden können.  
Dieses Symbol bedeutet, dass elektrische und  
elektronische  
Geräte  
am  
Ende  
ihrer  
Nutzungsdauer vom Hausmüll getrennt entsorgt  
werden sollen.  
Bitte entsorgen Sie dieses Gerät  
bei Ihrer örtlichen kommunalen  
Sammelstelle oder im Recycling  
Centre.  
9
 

Coleman Camping Equipment 5132A User Manual
Coleman Camping Equipment 5327 User Manual
Crosley Clothes Dryer 134856200 User Manual
Curtis Home Theater System DVD1073 User Manual
Desa Tech Gas Heater CGN20TA User Manual
Dukane Projector 8784 User Manual
Extron electronic Speaker SI 28W User Manual
Freecom Technologies Computer Drive FHD xx User Manual
FUNAI Flat Panel Television MJ414FG User Manual
GE Air Conditioner AER05 User Manual