Edelbrock Automobile Parts 2 4 W D User Manual

Edelbrock Cat-back Exhaust System  
Catalog #5710  
Applications: 1999-2006 1500/2500 Standard Cab,  
Short Bed Pick-Up, 4.8L & 5.3L V8, 2 & 4 W/D  
INSTALLATION INSTRUCTIONS  
Please study these instructions carefully before installing your new Cat-back Exhaust System. If you have any questions,  
contact our Technical Hotline at: 1-800-416-8628 , 7am - 5pm, Monday-Friday, Pacific Standard Time or e-mail us at  
edelbrock@edelbrock.com.  
Suggested Tools for Installation:  
K 3/8" ratchet set with SAE and metric sockets  
K 9/16” & 15mm wrench  
K Jackstands and jack  
K Liquid penetrant and rubber lubricant  
DISASSEMBLY  
2. Slip the muffler onto the intermediate pipe with a  
3-1/2" band clamp on the front. Note: Inlet end of  
muffler is marked. Snug the clamp so you can adjust  
the system later.  
1. Raise vehicle and support with proper jackstands for  
the weight, leaving the suspension hanging.  
2. Use caution around hot exhaust systems to avoid  
burns.  
3. Install a 3-1/2" band clamp on the front of the  
overaxle pipe and engage it into the stock rubber  
hanger as you slip it into the muffler. Snug the  
clamps.  
3. Use penetrating oil on all nuts and bolts.  
Note: Some 2001 and newer GM Trucks have a  
brace bar attached to the left and right side frame  
rails. Remove bolt and swing bar out of the way  
during installation.  
4. Provided in the installation kit are 2 hanger clamp  
assemblies. Using the correct one for the year of  
your vehicle, slip the clamp over the outlet of the  
overaxle pipe and engage into the rubber hanger  
#23-4041 for 1999-2002, and #23-4042 for 2003-  
2006 model year.  
4. Remove the bolts and clamps from the system and  
lubricate the rubber hangers.  
5. Use a long pry bar to pull the rubber hangers off of  
the pipe hangers.  
5. Slip tailpipe onto overaxle pipe, and snug the hanger  
clamp.  
6. Remove the old system. In some cases, you will find  
it easier to cut the overaxle pipe to remove it.  
6. Working from the front of the system, align and  
tighten each pipe from the cat-back.  
ASSEMBLY  
7. Check for clearance to body, frame, and driveline as  
you tighten the system from front to rear.  
1. Bolt I-Pipe to factory outlet flange (behind catalytic  
converters). Make sure that you have engaged the  
stock rubber hanger with the wire hanger welded to  
the pipe.  
8. Re-attach the brace bar to frame rail (if equipped).  
9. Check for leaks and correct, if any is found.  
Note: Do not tighten flange bolts at this time,(snug  
only).  
WARNING!!!  
Exhaust gas contains carbon monoxide, a deadly invisible gas. Correct any leaks before driving!  
©2005 Edelbrock Corporation  
Catalog #5710  
Page 1 of 2  
Brochure #63-0368  
Rev. 11/05 - DA/mc  
 

Corinex Global IP Phone VoIP USB Phone User Manual
Craftsman Saw 137248830 User Manual
Creative Labs Speaker System P380 User Manual
Crosley Microwave Oven CMT135SG User Manual
Curtis Flat Panel Television PL4210A 2 User Manual
Dymo Projector M1011 User Manual
Everpure Water System S 104 User Manual
Ferris Industries Lawn Mower is3100z series User Manual
Fisher Paykel Oven OB60S9DE User Manual
Fisher Price Motorized Toy Car 74558 User Manual