Cornelius Ice Maker CCM430 User Manual

ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions  
INSTALLATION INSTRUCTIONS  
ED2XX 30” CCM330/430/530/630/830/1030 NORDIC BLACK/GRAY  
STYLE LID KITS  
This Nordic style kit applies to the Cornelius 30” wide CCM322/522 ice maker.  
Item  
No.  
Part No.  
53003  
52969  
15537  
29565  
70217  
50904  
90221  
Name  
Qty.  
1
Cover, Gray  
Cover, Black  
Lid Assembly  
Bracket  
1
2
3
4
5
6
7
8
9
1
2
6
1
1
1
2
2
1
2
1
1
#8 Screw  
RTV  
Label  
620204731INS Installation Instructions  
620701902  
620701901  
Acorn Nut, 8--32 Nylon  
Sealing Washer  
Baffle, Ice  
10 620037003  
11 621701903  
12 620505802  
13 630500109  
#8 Nylon Washer  
Insulation Strip  
Bin Stat  
CAUTION: Disconnect electrical power to the dispenser before proceeding with the icemaker  
adapter kit installation.  
1.  
2.  
Unpack Kit.  
Place insulation strip (item 12) over studs on the baffle and insert baffle assembly into the adapter  
lid.  
3.  
Place (2) sealing washers (item 9) over studs and (2) flat washers (item 11), then fasten in place  
with (2) plastic acorn nuts (item 8)  
4.  
5.  
Set icemaker lid on the top of the dispenser.  
Using the slotted holes in the lid as a template, drill four (4) .140_ diameter (9/64_) holes at the  
bottom of the slots (see detail A). Use extreme care not to drill into the hopper. Fasten the lid to the  
dispenser with four (4) #8 sheet metal screws, two on each side.  
Seal the icemaker to the top of the dispenser as follows:  
6.  
A. Run beads of RTV around the opening in the lid and inside of the perimeter of the icemaker  
outline so that the icemaker will set on the RTV.  
B. Set the icemaker onto the lid and position it as required.  
C. Wipe away the excess RTV.  
7.  
8.  
Drill 9/64” diameter holes into the icemaker cabinet using the bracket as a template. Use extreme  
care not to drill into any icemaker components (condenser, tubing, etc.). Secure the brackets using  
the screws provided.  
Install the wire form bracket, supplied with the bin stat kit (item 4), through the 5/8” diameter hole in  
the bottom of the ice maker. Wrap the eye of the wireform over the stud near the hole to the end of  
the wireform bracket and wrap the tube around the end of the bracket several times, insuring the  
tube is secure.  
NOTE: The bin stat must not interfere with the agitator rotation or in the path of ice falling from  
the icemaker. If it interferes with the agitator or in the path of ice, bend the bracket out of the way.  
Release Date: October 5, 2007  
© 2007, IMI Cornelius Inc.  
Revision: A  
Publication Number: 620204731INS  
- 1 -  
 
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions  
ICEMAKER  
SEAL ICEMAKER TO  
ITEM 2 WITH ITEM 5 (RTV)  
DETAIL ”A”  
ENLARGED  
DRILL 9/64 (.140) DIA.  
HOLES USING BOTTOM  
OF SLOTTED HOLES AS A  
TEMPLATE.  
4
(2) PLCS.  
3
2
3
4
(6) PLCS.  
4
6
1
VIEW ”A”  
FIGURE 2. ED2XX Kit  
© 2007, IMI Cornelius Inc.  
- 3 -  
Publication Number: 620204731INS  
 
ED2XX 30” CCM330/430/530/630/830/1030 Nordic Style Lid Kit Installation Instructions  
FIGURE 3. Bin Stat  
Publication Number: 620204731INS  
- 4 -  
© 2007, IMI Cornelius Inc.  
 

Cobra Electronics GPS Receiver 4400 User Manual
Cooper Lighting Indoor Furnishings 201 IW User Manual
Craftsman Lawn Mower 91738862 User Manual
Cypress Computer Hardware CY7C65113C User Manual
Cypress Computer Hardware CY62157EV30 User Manual
Dimplex Water Heater DEE 1802 User Manual
Exergen Network Card IRt cXMTR User Manual
Fender Musical Toy Instrument Brown Derby User Manual
Geemarc Answering Machine RP7510 User Manual
Global Machinery Company Saw TTS5000M User Manual