Cooper Lighting Work Light EPL DLS Envoy User Manual

EPL/HS, EPL/HSCF, EPL/DLS Envoy  
House Side Shield or Drive Lane Shield  
Sheet 1 of 1  
INSTALLATION INSTRUCTIONS  
4/7/08  
IMI-695C  
IMPORTANT : READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN FOR FUTURE REFERENCE  
GENERAL: Upon receipt of luminaire thoroughly inspect for any freight  
damage, which should be brought to the attention of the delivery  
carrier. Compare the catalog description listed on the packing slip  
with the luminaire label on the housing to assure you have received the  
correct merchandise.  
WARNING: Make certain power is OFF before starting installation or  
attempting any maintenance.  
WARNING: Risk of Electric Shock. Disconnect power at fuse or circuit  
breaker before installing or servicing.  
WARNING: Risk of Burn. Disconnect power and allow luminaire to cool  
before changing lamp or handling luminaire.  
WARNING: This luminaire is for use with downlight application only.  
WARNING: RISK OF FIRE! DO NOT mount on or near combustible  
materials.  
SAFETY: This luminaire must be wired in accordance with the national  
electrical code and applicable codes and ordinance. Proper grounding  
is required to insure personal safety. Carefully observe grounding  
procedure. All work should be done by a qualified electrician.  
FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR  
DEATH  
Figure 1  
UPPER REFLECTOR  
UPPER HOUSE SIDE SHIELD (HS) ACCESSORY (ENVOY PARKING  
LUMINAIRE) INSTALLATION: (Figure 1)  
1. Unlatch both latches to allow lens to swing open.  
CAUTION: Support the lens while it swings open.  
LENS LATCH  
2. Install upper HS on the upper reflector on the side where light is to be  
shielded (with provided #6-32 screws).  
Note: Maximum quantity of (2) sets of house side shield may be used for  
total coverage of 180°.  
BOTTOM HOUSE SIDE SHIELD (HS) OR DRIVE LANE SHIELD (DLS)  
ACCESSORY (ENVOY PARKING LUMINAIRE) INSTALLATION:  
1. Unlatch both latches to allow lens to swing open.  
CAUTION: Support the lens while it swings open.  
Note: Detach lens from die cast housing if necessary by removing #8-32  
screw and retainer (Figure 3).  
UPPER HS  
#6-32 SCREW  
Figure 2  
BOTTOM HS RETAINER;  
SLIDE DOWN BETWEEN MAIN  
REFLECTOR AND LENS  
TOP EDGE OF  
MAIN REFLECTOR  
CAUTION: Support the lens while removing screw and retainer.  
2. Run wire retainers behind the main reflector on the side where light is to be  
shielded (Figure 2).  
3. Slide bottom HS or DLS onto bottom hook of wire retainers.  
Note: Curve of shield should follow inside contour of lens (Figure 2).  
4. Hook top wire retainers to the top edge of main reflector (Figure 2).  
Note: Drive lane shield accessory is normally positioned in center of lens in  
line with drive lane. Two (2) shields may be used for 2-way driving. For  
1-way driving; shield should be placed on side towards on-coming traffic.  
BOTTOM HS  
OR GLARE SHIELD  
Figure 3  
LATCH  
RETAINER  
#8-32  
SCREW  
These instructions do not claim to cover all details or variations in the equipment, procedure, or process described, nor to provide directions for meeting every possible contingency during installation,  
operation or maintenance. When additional information is desired to satisfy a problem not covered sufficiently for user’s purpose, please contact your nearest representative.  
NOTE: Specifications and dimensions subject to change without notice.  
Customer First Center 1121 Highway 74 South Peachtree City, GA 30269 770.486.4800 FAX 770.486.4801 ADH080774  
 

Code Alarm Automobile Alarm CA 430 User Manual
Country Home Products Vacuum Cleaner DR User Manual
Craftsman Cordless Sander 17210721 User Manual
Craftsman Saw 28617589 User Manual
Craftsman Trimmer 358 79104 User Manual
Crosley Radio Cordless Telephone CR56 User Manual
Danby Washer DTT420 User Manual
EverFocus Security Camera EPTZ3100 User Manual
Generac Power Systems Portable Generator 04136 0 User Manual
Global Machinery Company Drill GTX1850K User Manual