Coleman Tent 2000002250 User Manual

CABIN TENT 13’ X 9’  
MODEL 2000002250  
7. Rotate metal Leg Poles to upright position; then insert metal  
pin on web strap at front, back, & four corners of tent into  
bottom of each pole. (Fig. 2 & 2A)  
Before you begin  
Read all instructions before set up.  
• Select a level site clear of rocks, branches, and other hard or sharp  
objects, to install your tent.  
NOTE: You can use the tri-glide to adjust the length of the  
center webbing to make it easier to insert the metal pin into  
the metal center pole.  
WARNING: Keep clear of overhead power lines.  
• Do not set up your tent under trees because of potential lightning strikes  
or falling tree limbs in inclement weather.  
8. Snap large frame clips on seams of tent onto metal Leg Poles  
to secure. (Fig. 2 & 2B)  
• Secure with all stakes and guylines provided to prevent property damage  
or personal injury.  
• For best results in windy conditions, position narrow end of tent into  
the wind.  
9. Stretch four corners of tent until taut; then drive metal stake  
through ring on web strap of each to secure (Fig. 2 & 2C).  
10. Stretch web strap at front & back of tent until taut; then drive  
metal stake through ring on each to secure (Fig. 2 & 2C).  
• Enlist the help of at least one other person to assist you when it is time  
to assemble the tent.  
Fig. 2  
Pole Descriptions  
Pole  
Pole  
Pole  
Description  
Qty. Dia.  
Repair Kit Replacement Kit  
Leg Pole, metal  
4
19mm  
N/A  
N/A  
5010000650  
5010000651  
Leg Pole, metal,  
with white marking  
2
1
2
19mm  
Top Pole, thick, grey,  
Top Pole, thick, black  
12.7mm 5010000538 5010000550  
12.7mm 5010000538 5010000550  
Door Pole, long, thin, black,  
fiberglass, rubber tips  
1
1
6.3mm 5010000543 5010000545  
6.3mm 5010000543 5010000545  
Vert. Door Pole, short, black,  
fiberglass, rubber tips  
2A  
Tri-Glide  
To Set Up Tent  
1. Unfold tent and spread out on a clean, level surface with the  
door facing the desired direction. (Fig. 1)  
2C  
2B  
2. Assemble all fiberglass and metal poles by interlocking the  
shock-corded, sections together.  
3. Insert thick, black, Top Poles through the sleeves on top of  
tent forming an X”; then push end of each pole into black Pole  
Connector to form an arch. (Fig. 1 & 1A)  
4. Insert thick, grey Top Pole through the grey trimmed center  
sleeve, running from the front to the back of tent; then push  
end of pole into black Pole Connector to form an arch.  
(Fig. 1 & 1B)  
5. Insert four metal Leg Poles into end of Pole Connectors at the  
four corners of the tent. (Fig. 1 & 1C)  
NOTE: Make sure end with metal “V” spring is inserted into  
Pole Connector.  
6. Insert two metal Leg Poles (with white markings) into end  
of Pole Connectors at front & back of the tent. (Fig. 1 & 1C)  
NOTE: Make sure end with metal “C” spring is inserted into  
Pole Connector.  
Hinged, Rigid Door  
1. Insert Vertical Door Pole (shorter black  
pole with plastic cap tips) through zippered  
vertical sleeve on hinged side of door.  
(Fig. 3)  
2. Insert end of Vertical Door Pole into bottom  
hinge plate, apply pressure to form a slight  
Pole  
Sleeve  
bow, then insert other tip of pole into top  
hinge (Fig. 4). Zip up vertical pole sleeve.  
3. Insert Door Pole (long, black pole with  
plastic cap tips) into zippered pole sleeve  
Fig. 3  
at top of door. (Fig. 5)  
Fig. 4  
4. Insert end of Door Pole into top hinge  
plate, apply pressure to form a bow, then  
insert other tip of pole into the bottom  
hinge. (Fig. 6)  
Pole  
Pole  
5. Zip up “C” shaped pole sleeve to  
Connector  
Connector  
enclose Door Pole. (Fig. 7)  
Fig. 5  
Pole Sleeve  
Metal Leg Poles  
1B  
1A  
Metal Leg Pole with  
White Marking  
Metal Leg Pole  
Metal Leg Pole  
Fig. 7  
Fig. 6  
Door & Front of Tent  
Metal Leg Pole with  
White Marking  
To Attach Rainfly  
1. Drape Rainfly over tent with the triangle-shaped leg flaps with  
elastic cords centered over the four corner of the tent. (See  
Fig. 8 on other side of this tag).  
Fig. 1  
“C” Spring  
NOTE: Hook and loop fasteners, located on seams of under  
side of rainfly, should be centered over the Leg Poles.  
(continued on other side)  
1C  
 

Clover Electronics Security Camera HDC100 User Manual
Continental Dehumidifier PS78403 User Manual
CTX Computer Monitor PV722E User Manual
Curtis Flat Panel Television LCD2226A User Manual
DLS Svenska AB Speaker IRIDIUM 10I User Manual
Dymo Label Maker 1755 User Manual
Everpure Water System MR 225 User Manual
Frigidaire Cookware FPES3085K F User Manual
Fujitsu All in One Printer fi 434PR User Manual
GE Ventilation Hood 30 User Manual