Carbine Automobile Accessories PLUS 5900 User Manual

PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 1  
R
Automotive Security  
User’s Manual  
Model: PLUS-5900  
For Technical Assistance, please call (800) 638-3600,  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 3  
Remote Control Transmitters  
The LCD screen on the 2-way remote control displays graphic icons. It provides visual information  
on any trigger of the sensors and around the clock surveillance of your vehicle, as well as  
displaying the present status of the system.  
2-Way LCD Remote  
LCD Display Icons  
1-Way Backup Remote  
LCD Remote Icons  
Door Lock  
Vehicles Doors are Locked  
Warn Away  
Shock Sensor Triggered (Zone 1)  
Door Unlock  
Vehicles Doors are Unlocked  
Shock Sensor  
Shock Sensor Triggered (Zone 4)  
Armed Mode  
Security System is Armed  
Power Save Mode  
Saves The Battery Power when  
Transmitter is not in Use  
Valet Mode  
Security System is in Valet Mode  
Vibrate Mode  
Vibrates when Security System is Triggered  
Remote Transmission  
Transmitting a Signal  
Low Battery  
Replace the Transmitter Battery  
In-Range Indicator  
You are within Remote Control Range  
Ignition  
Door Triggered  
Trigger On Ignition Switch (Zone 5)  
Doors are Opened (Zone 3)  
Driver Paging / Lost and Found  
Someone is Paging you from the Vehicle  
Trunk/Hood Triggered  
Trunk/Hood are Open (Zone 2)  
System Trigger/Panic  
Alerts that the System has been  
Triggered  
Second Vehicle  
Communicate with a Second Vehicle’s  
Security System  
3
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 4  
Remote Control Transmitters Operation  
Transmitter Button  
System Function  
Remark  
Lock Doors & Arms System  
Press and Release  
Arm and Delete the 2-Stage  
Shock Sensor  
Press Twice within 3 Seconds  
-
-
Arm System and  
Hidden Alarm Function  
Press within 3 Seconds  
Panic Alarm  
Press and Hold for 3 Seconds  
System Armed Longer than 30  
Seconds  
Progressive Car Locator  
Silent Arming/Disarming  
Manual Anti-Car Jacking Mode  
Press at the same Time  
+
+
Ignition in “ON” Position,  
Press and Hold for 2 Seconds  
Press Both and Hold Until the  
Door Locks Cycle  
RF Valet Mode On  
+
Press and Release  
Unlock Doors & Disarm System  
Two Step Door Unlock and  
Disarm System  
Press Twice within 3 Seconds  
-
Press Both and Hold Until the  
Door Locks Cycle  
RF Valet Mode Off  
+
Trunk Release - Channel 3  
Press and Hold for up to 3 Seconds  
Passive Arming Bypass  
-
Press Twice within 3 Seconds  
Press and Release  
Channel 4 Timer Control Output  
Press and Hold  
Hear a Long Beep then Press  
+
Together  
2nd Car Control  
(LCD Transmitter Only)  
-
+
4
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 5  
Programming the LCD Transmitter  
Vibration/Melody Mode  
This mode is useful when you are in a noisy place and it is difficult to hear the beep from the  
transmitter. While in the Vibration/Melody Mode, the transmitter will vibrate if your security  
system has been activated.  
1. Press and hold the  
and buttons at the same time until one long beep is  
heard. Programming has now been entered.  
2. Within 5 seconds, press the button to select the vibration or Melody Mode.  
The icon will be displayed on the screen to show the remote transmitter is  
in Vibration Mode.  
3. To exit the Programming Mode, take no action for five seconds. The remote  
control will generate two long beeps to indicate Programming Mode has been  
exited.  
Power Save Mode  
While in the Power Save Mode, the LCD remote transmitter will “Sleep” until a  
button is pushed, extending the life of battery. When Power Save Mode is “OFF”,  
the remote control will wake up periodically to check for messages from the  
security system.  
1. Press and hold the and buttons at the same time until one long beep is  
heard. Programming has now been entered.  
2. Within 5 seconds, press the button to toggle between “ON” or “OFF”. The  
remote will beep twice for “ON”, and once for “OFF”. When Power Save Mode is “ON”, the  
icon on the LCD screen indicates entry into Power Save Mode.  
3. To exit Programming Mode, take no action for five seconds. The remote control will generate  
two long beeps indicating Programming Mode has been exited.  
Screen Lamp On  
Press the button once, and the LCD screen lamp will turn on for 5 seconds.  
System Status Check  
To check the system’s present status through the LCD screen, press the  
transmitter button first, then within 3 seconds press  
and buttons at the  
same time. The response will be one melody sound, and the LCD screen will be  
illuminated. Note: If no response is received, then you are out of range.  
Clear the Flash Icon and Melody Sound  
Press the  
button first, then within 3 seconds press the  
and buttons at the same time.  
These steps will clear the flash icon and melody sound on the LCD transmitter.  
Stop the Trigger Melody Sound  
While triggering the alarm the LCD screen will alert the user through a melody sound and a  
flashing trigger icon. Press any button on the LCD transmitter to stop melody sound only, and  
the remote control will not send a command to the system.  
5
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 6  
Programming the LCD Transmitter  
Press Buttons at the Same Time: Then Press Button Within:  
System Function  
Switching to 2nd Vehicle  
or Returning to 1st  
Vehicle Operation  
5 Sec.  
+
Melody / Vibration Mode  
Power Save Mode  
+
+
5 Sec.  
5 Sec.  
LCD Screen Lamp  
Turns On for Five Seconds  
System Status Check  
3 Sec.  
3 Sec.  
+
+
Clear the Flash Icon  
and Melody Sound  
Battery Replacement  
The LCD remote control is powered by a 1.5 Volt  
AAA Alkaline battery. When the power of the  
battery weakens the battery icon  
will be  
displayed on the screen. When the old battery is  
replaced with a new one, there will be a beep to  
indicate the power is up. To replace the battery,  
follow the steps in the illustration at left.  
Note: Press the  
button two times when the  
battery compartment is empty, then insert the  
new battery.  
LED Indicator  
LED  
Function  
OFF  
System is Disarmed  
Slow Flashing  
Fast Flashing  
LED On Solid  
System is Armed  
Automatic Arming Timer is Counting Down  
System in Valet Mode (Ignition Key On)  
1 Flash Every 5 Seconds System in Valet Mode (Ignition Key Off)  
2 Flashes - Pause  
3 Flashes - Pause  
4 Flashes - Pause  
5 Flashes - Pause  
Zone 2, Trigger from Trunk/Hood  
Zone 3, Trigger from Door Switch  
Zone 4, Trigger from Shock Sensor  
Zone 5, Trigger from Ignition Switch  
6
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 7  
Interference  
The transmission range may decrease if the system encounters interference from tall structures or  
stronger radio frequencies such as high-voltage power lines.  
Parking Lights  
Flash  
Function  
1 Flash  
System is Armed  
System is Disarmed  
Disarmed / Triggered  
Car Locator  
2 Flashes  
3 Flashes  
3 or 6 Flashes  
Chirp Indicators  
Chirp  
Function  
1 Chirp  
System is Armed  
System is Disarmed  
Ajar Warning  
2 Chirps  
3 Chirps  
4 Chirps  
Disarm / Triggered  
Progressive Car Locator  
2, 3 or 6 Chirps  
System Characteristics  
Parking  
Light  
Siren/Horn  
LED  
Doors  
Starter  
Dome Light  
1or 3  
1. Arming  
Disabled  
(Option)  
1 Flash  
Slow Flash  
Locking  
Chirps  
2 or 4  
2. Disarming  
2 or 3  
Flashes  
Turns on for  
30 Seconds  
Unlocking  
Chirps  
Disabled  
(Option)  
3. Trigger  
4. Panic  
Alarming  
Alarming  
Alarming  
Flashes  
Flashes  
Flashes  
Slow Flash  
Flashes  
Flashes  
Flashes  
5.Car  
Jacking  
Disabled  
(Option)  
2, 3 or 6  
Chirps  
3 or 6  
Flashes  
6.Car  
Locator  
Locking  
7
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 8  
Manual Arming: Lock & Arm  
1. Press the button on the transmitter.  
2. The siren will chirp once and parking lights will flash once indicating that the system is now  
armed. The vehicle door will lock upon arming when interfaced with the security system.  
System Armed  
Door Ajar  
Trunk/Hood Ajar  
Ajar Warning:  
If the siren sounds 3 chirps, then  
you have left a door, trunk, or hood  
lid ajar.  
Silent Arming/Disarming  
Press the transmitter and buttons at the same time to arm or disarm your security system.  
No chirp sound will be heard. The arm/disarm confirmation will be through the vehicle’s parking  
lights only.  
Shock Sensor Bypass  
Press the  
button on the transmitter two times within 3 seconds. This will arm the security  
system and bypass the shock sensor. The system will chirp one additional time to confirm the  
Sensor Bypass Mode was activated. The sensor bypass feature is programmed to activate for  
one arming cycle only. The security system will return to normal operation during the next  
arming cycle.  
Hidden Alarm Function  
Press the  
button first, within 3 seconds press the  
button to activate the hidden alarm  
function. The security system will arm, but the siren / horn will be silenced even if the sensor is  
triggered in the armed status.  
Automatic Arming  
Manual arming/disarming is controlling your security system via the remote transmitter. This  
security system is equipped with an optional Automatic Arming feature which allows the security  
system to arm 45 seconds after the last door is closed. Operation is as follows:  
1. Turn the ignition to the “OFF” position and exit the vehicle.  
2. After all entrances are closed, the security system LED will flash fast for 45 seconds. If you  
reopen any Door, Hood, Trunk the security system LED will stop flashing. It will begin flashing  
again once the vehicle’s entrances are closed.  
3. After the 45 second timer has elapsed, the security system will automatically “ARM”. The  
siren/horn will chirp once, and the parking lights will flash once.  
Automatic Arming with Automatic Door Locking (Programmable)  
If this feature has been programmed on, the vehicle doors will automatically lock after the  
automatic arming cycle has been completed.  
8
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 9  
(continued)  
Automatic Arming  
Automatic Arming Bypass  
While the system is in Disarmed Mode, press the  
button twice. The horn/siren will respond  
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as  
long as you wish. To exit this mode press the  
normal status.  
or  
buttons and the system will return to  
Manual Disarming Unlock & Disarm  
1. Press the  
button on the transmitter.  
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now  
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon  
disarming when interfaced with the security system.  
System  
Disarmed  
Doors  
Triggered  
Trunk/Hood  
Triggered  
Shock Sensor  
Triggered  
Ignition  
Triggered  
Tamper Disarming  
If the security system is triggered upon disarm, the siren will chirp 4 times and the parking lights  
will flash 3 times.  
Pathway Illumination  
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10  
seconds upon the lock signal.  
Two-Step Door Unlock  
This feature will independently unlock the driver’s door only when disarming the security system.  
Pushing the button a second time within 3 seconds will unlock the other doors.  
Automatic Rearm  
If this feature is selected, the security system will automatically rearm itself within 60 seconds  
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened  
before the 60 second timer has elapsed.  
Disarming without a Transmitter  
The override function may be used if the remote transmitter is lost or inoperative.  
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will  
sound).  
2. Within 10 seconds push and release the valet switch. The alarm will stop  
sounding and enter the Disarm Mode. You can now start and operate the  
vehicle normally.  
Push and  
Release  
9
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 10  
RF Valet Mode (Applies to All Transmitter Types)  
RF valet mode provides the same functions as manual valet mode but allows you to enter and exit  
the valet mode using the remote transmitter. When the system is in Valet Mode, all alarm  
functions and remote start functions are off. However, the remote panic feature and remote door  
locks remain operational. To enter/exit the RF Valet Mode, repeat the following procedures.  
Enter Valet Mode  
1. In Disarmed Mode, open the drivers door.  
2. Push and hold the and transmitter buttons until the door locks cycle  
“Lock then Unlock”. The LED will flash every 5 seconds to indicate that the  
unit is in the Valet Mode.  
Note: When the unit is in valet mode, the LCD transmitter  
icon will be  
displayed.  
Exit Valet Mode  
1. In Unlocked Mode, open the drivers door.  
2. Push and hold the and  
transmitter buttons until the door locks cycle  
“Lock then Unlock”. The LED will stop flashing every 5 seconds to indicate  
that the unit is out of the Valet Mode.  
Note: When the unit is out of valet mode, the LCD transmitter  
icon will be  
off and you will hear a short melody from the transmitter.  
Manual Valet Mode  
Manual valet mode allows you to bypass all alarm functions eliminating the need to hand your  
transmitter to parking attendants or garage mechanics. This mode is also a necessity if your  
transmitters become in-operable. When the system is in Valet Mode, all alarm functions and  
remote start functions are off. However, the remote panic feature and remote door locks remain  
operational. To enter the Manual Valet Mode, the system must first be disarmed either by using  
your remote transmitter, or by operating the manual override sequence.  
Enter Valet Mode  
1. When in Disarmed Mode, turn the ignition to the “ON” position.  
2. Push and hold the valet switch for 2 seconds. The LED will flash every 5  
seconds as long as the unit is in the Valet Mode.  
Note: When the unit is in valet mode, the LCD transmitter  
displayed.  
icon will be  
Hold for  
2 Seconds  
Exit Valet Mode  
1. To return to normal operation, turn “ON” ignition.  
2. Push and hold valet switch for 2 seconds. The LED will stop flashing, indicating the system  
has now exited the Valet Mode.  
Note: When the unit is out of valet mode, the  
icon will be off and you will hear  
a short melody from the transmitter.  
10  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 11  
Remote Panic Function  
The transmitter can be used as a remote panic switch to manually trigger the alarm system in  
case of an emergency.  
1. Press and hold the button for 3 seconds to enter the Panic Mode (horn/siren will start to  
sound and parking lights will flash).  
2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door  
(if that option is installed). However, if the  
device (when installed) will be disabled, allowing the vehicle to start.  
3. To turn off the panic function, press and hold the button again for 3 seconds or press and  
release the or buttons.  
button is pressed, the vehicle’s starter disable  
4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30  
seconds.  
Anti-Car Jacking  
Warning: This security system has a car jacking feature. Its default setting is “OFF”. So be sure to  
enable this feature if you feel it is needed.  
Manual Anti-Car Jacking  
1. Press and hold the transmitter and buttons at the same time for 2 seconds while the  
vehicle’s ignition is “ON”. The parking lights will turn on for 1.5 seconds to indicate the  
system has entered the Anti-Car Jacking Mode.  
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door  
is opened and closed while the ignition is “ON”.  
Automatic Anti-Car Jacking  
1. Turn the ignition switch to the “ON” position, and the system will enter the Anti-Car Jacking  
Mode.  
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door  
is opened and closed while the ignition is “ON”.  
When the Anti-Car Jacking Feature is Triggered  
a. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.  
b. During this 15 second period of chirping, you can push and release the valet switch once to  
turn off the car jacking feature.  
c. 65 seconds after the system has been triggered. The siren starts sounding and the parking  
lights start flashing. You must follow the override procedure to stop the system at this point.  
d. 90 seconds after the system has been triggered:  
1. The siren will still be sounding and the parking lights flashing.  
2. The starter disable will activate to prevent the vehicle from starting.  
3. Anti-Car Jacking Mode will remain active until the override procedure is performed or the  
vehicle's battery power is exhausted.  
Override the System to Turn Off Anti-Car Jacking  
Turn the ignition switch from “OFF” to “ON”, and within 10 seconds push the valet switch. The  
siren will stop sounding and the security system is now disarmed.  
11  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 12  
Progressive Remote Vehicle Locator System  
Note: The remote vehicle location system is active 30 seconds after the alarm is armed.  
1. Press the button to active the vehicle locator system. The horn/siren will beep 2 times and  
the parking lights will flash 3 times. This operation will repeat a second time.  
2. Press the button again within 30 seconds. The horn/siren will beep 3 times and the parking  
lights will flash 3 times. This operation will repeat a second time.  
3. Press the button again within 30 seconds. The horn/siren will beep 6 times and the parking  
lights will flash 6 times.  
Dome Light Supervision  
The Security System has a unique feature for using your vehicle’s dome light:  
1. Upon disarming the vehicles security system, the interior dome light will remain on for 30  
seconds.  
2. If the security system is triggered, the dome light will flash for the same duration as the  
horn/siren.  
Note: Turn “ON” the ignition switch or arm the system to turn off the dome light.  
Ignition Controlled Door Locks  
If the vehicles door locks have been interfaced with the security system, the system will  
automatically lock the doors when the ignition is turned “ON”, or unlock the doors when ignition  
key is turned “OFF”.  
Trunk Release Output (Channel 3)  
Press and hold the  
button for up to 3 seconds to activate the trunk release (Channel 3 Output)  
and/or any other devices connected.  
Timer Control Output (Channel 4)  
Press and release the  
button to activate the Channel 4 output. Channel 4 is user programmable  
timer output. You may program the built-in timer to send a ground signal for any time duration  
between 1 and 120 seconds. For example, this timer output may be used to turn on the  
headlights, power window or sunroof (Factory defaults setting at momentary output.)  
Driver Paging / Lost and Found (For LCD transmitter only)  
Driver Paging / Lost and Found is useful when someone inside the vehicle wants  
to page the driver, or if the LCD transmitter has been misplaced.  
With the ignition switch in the “OFF” position, press and hold the valet switch for  
2 seconds to page the LCD transmitter. One chirp shall be emitted and the  
paging melody continues sounding from the LCD transmitter and  
on the screen.  
will flash  
12  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 13  
Out-of-Range Indication  
If the Out-of-Range Indication feature is activated the system will automatically check the range  
every 30 minutes after being armed.  
1. If the user is within the range, the icon will appear on the LCD screen.  
2. If user is out-of-range, the  
beeps 5 times.  
icon will disappear from the LCD screen and the transmitter will  
Note: Activating this feature will decrease the life expectancy of the battery.  
Power-On Memory  
This security system is equipped with circuitry that will allow the unit to remember its alarm state  
if the power is lost and then reconnected.  
Second Carbine Security System Operation  
If your transmitters have been programmed to a second Carbine security system, follow the steps  
below.  
For LCD Remote Control Transmitter  
Second Vehicle Operation: While the  
can remote control and communicate with a second vehicle security system.  
1. Press and hold and buttons at the same time until one long beep is  
icon is displayed on the LCD screen, you  
heard. Programming Mode has now been entered.  
Note: No action for five seconds will generate two long beeps indicating the  
Programming Mode has been exited.  
2. Within 5 seconds, press and hold the  
the icon is displayed on the LCD screen indicating second vehicle operation.  
3. While the is displayed, press any button on the transmitter to control the second vehicle’s  
button until two beeps are heard and  
security system or alarm function (arm/disarm/trunk).  
Note: Button functions are the same for the second vehicle as they are for the first vehicle.  
Return to First Car Operation  
1. Press and hold  
and buttons at the same time until one long beep is heard.  
Programming Mode has now been entered.  
Note: No action for five seconds will generate two long beeps indicating the  
Programming Mode has been exited.  
2. Within 5 seconds, press and hold the button until one beep is heard and the  
icon is not displayed on the LCD screen indicating first vehicle operation.  
13  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 14  
Replacement Transmitters  
TRANSMITTERS  
DESCRIPTION  
MODEL #  
$ PRICE  
2-Way LCD Remote for  
the PLUS5900 - PLUS6900  
Security System  
CARF-LCD2  
79.95 ea.  
1-Way Remote for  
he PLUS5900 - PLUS6900  
Security System  
CA-RF69  
MODEL #  
39.95 ea.  
$ PRICE  
Replacement Batteries  
REPLACEMENT BATTERIES  
DESCRIPTION  
1.5 Volt AAA Alkaline Battery commonly  
found in grocery stores, hardware stores,  
etc.  
CR2032  
4.95 ea.  
3 Volt Lithium Battery (1 pc.)  
14  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 15  
Parts and Accessories Order Form  
Mail to: Magnadyne Corporation  
ATTN: Consumer Parts Sales  
P.O. Box 5365  
Credit Card or Money Order Only  
(Sorry No Cash, C.O.D. or personal checks accepted)  
Call: (310) 884-7777 Fax: (310) 637-9542  
Carson, CA 90749-5365  
SHIP TO: (No P.O. Boxes)  
LAST NAME  
FIRST NAME  
INITIAL  
STREET ADDRESS  
ADDITIONAL ADDRESS  
ADDITIONAL ADDRESS  
CITY  
STATE  
ZIP CODE  
DAY TIME PHONE NUMBER  
CREDIT CARD INFORMATION  
VISA  
MC  
CREDIT CARD N0.  
EXPIRATION DATE  
CARD HOLDER’S LAST NAME  
STREET ADDRESS  
FIRST NAME  
INITIAL  
CITY  
STATE  
QTY.  
ZIP CODE  
PART #  
DESCRIPTION  
PRICE EACH  
TOTAL  
Shipping and Handling  
Sales Subtotal = ________ . ______  
Up to $20.00  
20.01 to 30.00  
30.01 to 45.00  
45.01 to 70.00  
Over 70.01  
$5.00  
5.95  
6.50  
6.95  
7.95  
California Residents Add Sales Tax = ________ . ______  
Shipping and Handling (See Chart) = ________ . ______  
TOTAL = ________ . ______  
On regular orders please allow 4-5 weeks for delivery.  
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.  
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.  
15  
 
PLUS-5900-UM.qxp 4/30/09 3:12 PM Page 16  
Limited Lifetime Warranty  
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original  
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the  
option of the Magnadyne Corporation or its authorized agents, if said product or part is found  
defective in materials or workmanship, when properly connected and operating on the correct  
power requirements designated for the specific product. This warranty and Magnadyne Corporation  
or its authorized agents obligations, hereunder do not apply where the product was: damaged while  
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably  
maintained, utilized in commercial or industrial operation, or serviced by anyone other than  
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken  
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its  
authorized agents do not assume any labor costs for the removal and reinstallation of any product  
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized  
agents. Such costs are the sole responsibility of the purchaser.  
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories  
used in connection with the product resulting from improper installation, alteration, accident,  
misuse, abuse or acts of nature.  
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither  
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile  
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness  
or any accessory item are covered by our standard 12 month limited warranty.  
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential  
or incidental damages or claims that may arise due to failure of product to operate properly  
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,  
replacement of the product as stated above if all conditions of the warranty are met. No  
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does  
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or  
against the loss or damage to the contents of any vehicle in which a security system is installed.  
Magnadyne security systems are only a deterrent against possible theft.  
This warranty extends only to the original purchaser of the product and for the vehicle in which it  
was originally installed. This warranty is not transferable or assignable to any person or vehicle.  
Defective merchandise should be returned to the original point of purchase or secondly to  
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must  
be obtained before sending, or merchandise may be refused.  
© Copyright 2009 Magnadyne Corporation  
PLUS-5900-UM 4-30-09 Rev. A  
 

Belkin Network Card 8820 01363 User Manual
Belkin Video Game Controller n45 User Manual
Blue Rhino Charcoal Grill CBT726M User Manual
Bravetti Blender FP200 User Manual
Briggs Stratton Automobile Parts 126300 User Manual
Canon Camera Lens 1257B002 User Manual
Capital Cooking Burner PRO 3L User Manual
Casablanca Fan Company Outdoor Ceiling Fan C3U72M User Manual
Chamberlain Garage Door Opener 1000SDR 1 3 HP User Manual
Cisco Systems Caller ID Box 7905G User Manual