Bradley Smoker Plumbing Product E19 120A User Manual

Installation  
Instructions  
Bradley Drench  
Shower Horizontal Supply  
Model E1  
Table of Contents  
Pre-Installation Information  
Installation Instructions  
Assembly of Components  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .  
2
3
4
4
IMPORTANT  
This equipment should be inspected,  
tested, and recorded weekly to maintain  
proper operation.  
Main water supply to the eye wash  
should be “ON” at all times.  
This installation manual and parts list  
should be filed by the building owner’s  
maintenance department.  
Ref. G; EN 98-579  
PO. Box 309, Menomonee Falls, WI USA 53052-0309  
PHONE (414) 251-6000 FAX (414) 251-5617  
Page 1 of 4  
 
Bradley Drench Shower Horizontal Supply  
Model No.  
Installation Instructions  
Pre-Installation Information  
Operation  
The drench shower is easily activated by pulling the triangular pull rod downward, and  
deactivated by pushing the triangular pull rod upward.  
Components  
Showerhead: The corrosion-resistant stainless steel showerhead has a 254 mm (10”) diameter.  
Shower Valve: The 1” IPS stay-open valve is operated by a stainless steel pull rod with a  
triangle handle.  
Water Supply: Water supply connection is 1” BSP horizontal.  
Pipe and Fittings: Pipe and fittings are galvanized steel, coated with  
safety yellow.  
Check Contents  
Separate all parts from packaging and check each part with Figure 2 and the Parts List on  
page 4. Make sure all parts are accounted for before discarding any packaging material. If any  
parts are missing, do not attempt to install your Bradley Drench Shower until you obtain the  
missing parts.  
Bradley Drench Shower Warranty  
Bradley Corporation warrants to commercial and institutional purchasers only each fixture free from defects in  
material and workmanship under normal use and service upon the following terms and conditions:  
1. We will replace, without charge, any part which proves to be defective within one year from date of our  
invoice at our option, F.O.B. Menomonee Falls, Wisconsin.  
2. This warranty does not cover installation or any other labor charge and does not apply to fixtures which have  
been damaged by accident, abuse or improper maintenance.  
3. The repair or replacement of the defective fixtures as stated in this warranty shall constitute the sole remedy  
of the purchaser, and the sole liability of the Bradley Corporation under this warranty. Bradley Corporation  
shall not otherwise be liable under any circumstances for incidental, consequential or indirect charges caused  
by defects in fixtures or any delay in the repair or replacement thereof.  
4. This warranty extends only to commercial and institutional purchases and does not extend to any others,  
including consumer, customers of commercial and institutional purchasers.  
5. This warranty is in lieu of all other warranties expressed or implied, including any implied warranty of mer-  
chants ability or fitness for a particular purpose, or otherwise.  
6. Bradley emergency fixtures are to be used as a supplement to first aid treatment. Bradley Corporation cannot  
guarantee  
when used this emergency equipment will prevent serious injury or the aggravation of existing  
or prior injuries. No other warranties, expressed or implied are authorized, provided or guaranteed by  
Bradley Corporation.  
Bradley Corporation l  
Ref. G; EN 98-579  
2
 
Bradley Drench Shower Horizontal Supply  
Model No.  
Installation Instructions  
Installation Instructions  
Supplies Required:  
l
l
l
l
Pipe sealant  
Piping to 1” BSP water supply inlet on unit  
Adequate supply pipe supports  
Minimum 102 mm (4”) drain to accommodate 115 liters per minute discharge for drench  
shower waste  
Step 1: Assemble drench shower  
NOTE: Flush the water supply line before beginning  
installation.  
1. Assemble drench shower components as shown  
in Figure 2 on page 4.  
2. Apply pipe sealant or tape (supplied by installer)  
to all male-threaded pipe joints.  
NOTE: Use a strap wrench around the pipes when  
tightening to prevent mm-ring.  
3. The bottom edge of the showerhead should be  
2134 mm  
from the floor.  
Step 2: Connect water supply  
Figure 1  
IMPORTANT: Do not rely on Bradley’s  
Drench Shower to support  
supply piping.  
1. Connect water supply piping to  
BSP inlet on unit (piping supplied by installer).  
Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or  
other means.  
2. Mount safety sign to wall or pipe using sign mounting hardware supplied.  
3. Open water supply lines. Test for leaks and adequate water flow.  
Installation Instructions continued..  
3
Bradley Corporation  
l
G; EN 98-579  
 
Bradley Drench Shower Horizontal Supply  
Model No.  
Installation Instructions  
1” BSP SUPPLY INLET  
Assembly of  
i
Figure 2  
Parts List  
ITEM  
4c  
PART NO.  
DESCRIPTION  
SCREW  
DESCRIPTION  
PART NO.  
ITEM  
2
1
BALL VALVE  
1
1
ADAPTER  
LOCKWASHER  
4D  
WASHER  
4E  
1
4
1
1
1
1
1
BALL VALVE  
HANDLE  
DIFFUSER PADS  
SIGN-MOUNTING HARDWARE  
4F  
128-129  
140-720  
STOP  
1
PULL ROD  
LONG  
PIPE 1” IPS  
8
r
2
3
1
EMERGENCY TAG  
SAFETY SIGN  
BSP ADAPTOR  
JAM NUT  
1
90” STREET ELBOW 1’ IPS  
STN. STL SHOWERHEAD ASSY.  
SHOWERHEAD SHELL  
DIFFUSER  
189-723  
1
1
1
1
8’  
9
4
1
153-298  
110-214  
4A  
187-053  
155-008  
1
10  
l
Not Shown  
Bradley Corporation  
l
Ref. G; EN 98-579  
4
 

Black Decker Coffeemaker BCM40B User Manual
Blue Rhino Patio Heater 235020 User Manual
Bosch Appliances Home Security System D1265 User Manual
Bosch Appliances Network Card FPE 1000 NE User Manual
Boss Audio Systems Car Stereo System BV8963 User Manual
Boss Audio Systems Car Stereo System CCR612 User Manual
Breville Blender BBL800 User Manual
Casio Digital Camera EX Z 2 User Manual
Chauvet Landscape Lighting MINI 4 BAR 20 User Manual
Cisco Systems IP Phone OL 21011 01 User Manual