Black Decker Fan BDHT5016 User Manual

16” High Velocity Air Circulator  
Instruction Manual  
Black & Decker and the Black and Decker logo are trademarks of the Black &  
Decker Corporation and are used under license. All rights reserved. Product  
may differ slightly from the picture on the cover of this instruction manual.  
MODEL NO.: BDHT-5016  
120V AC 60HZ 0.55A 70W  
PLEASE READ, FOLLOW AND  
SAVE THESE INSTRUCTIONS  
FOR HOUSEHOLD USE ONLY  
1
8
 
4
WARNING: This appliance has a polarized plug (one blade on the plug is wider than the  
other). To reduce the risk of electric shock, only use a polarized plug in a polarized  
outlet. If the plug does not fit easily into the outlet, turn the plug over so the right part of  
the plug fits in the outlet's other slot. If the plug still does not fit, contact a qualified  
electrician. Do not modify the plug in any way.  
DIAGRAM  
USER SERVICING INSTRUCTIONS  
1. Remove the plug from the receptacle or other outlet device. Do not unplug by pulling on  
the cord.  
2. Use a suitable tool such as a small flat screwdriver or travel scissors.  
3. When opening the fuse cover, slide open the fuse access cover on top of the attachment  
plug towards the blades. (See Fig.1)  
4. Carefully remove the fuse by prying it out. (See Fig.2)  
5. A fire can result from using the wrong fuse rating. Only replace fuses with a 2.5 Amp,  
125 Volt rating fuse. (replacement fuses are not included  
6. To close the fuse access cover, slide the fuse access cover on top of the attachment plug.  
(see Fig.3)  
OPERATING INSTRUCTIONS  
WARNING: Do not attach the fan to a window or place the fan near a window, as  
the risk of electrical shock exists and can cause serious personal injury and/or  
property damage.  
Fig.1  
Fig.2  
Fig.3  
1. Place the fan on a level surface that is completely dry.  
2.Make sure the rotary switch is at the “0” (OFF) position.  
3.Plug the unit into a 120 Vac 60Hz outlet.  
4.Adjust the fan head vertically to your desired angle.  
5.To run the unit, turn the rotary switch to the “L” (Low), “M” (Medium) or “H”  
(High) position.  
7. Do not replace the attachment plug because it contains a safety device (fuse) that should not  
be removed. Discard this product if the attachment plug is damaged  
6.To turn the unit off, turn the rotary switch to the “0” (OFF) position.  
7.Unplug the unit from the electrical outlet when it's not in use or is left unattended.  
WALL MOUNTING  
1. Choose a mounting location which will allow installation of hardware directly into  
wall studs or adequate structural support.  
2. Insert a screw (bolt) into the wall stud. Fasteners are not included. All applications  
will require different hardware, so please consult with a professional prior to  
installation. Suggest to use minimum screw size of 5/32X2".  
3. The screw length must be long enough to engage the wall stud. Leave  
approximately 7/8 of the screw (bolt) exposed to properly hang fan.  
4. Line up the opening on the base of the fan with the screw (bolt) and hang the fan  
on the wall.  
5. When mounting the fan to the wall, the cord set must be located outside the body  
of the fan.  
 
5
USA & Canada Customer Service Number:  
1-888-773-8744  
5870 NW 163th Street,  
Miami Lakes, Florida 33014  
USA  
3 Year limited warranty: Covers all defective materials and  
workmanship under normal household use.  
MADE IN CHINA  
7
2
 

Beko Washer Dryer 2012 CXY User Manual
Belkin Surge Protector AG110030 04 User Manual
Belkin Switch 1394 User Manual
BenQ Projector MP721 721c User Manual
Canon Camera Lens 23569 User Manual
Carrier Air Conditioner 50TFF004 014 User Manual
Casio Watch QW 1425 User Manual
Char Broil Gas Grill 463250811 User Manual
Chrysler Automobile 2005 Sebring Convertible User Manual
Cisco Systems GPS Receiver X350 User Manual