Banner Power Supply MPS 15 User Manual

MICRO-AMP® System  
MPS-15 and MPS-15-230 Power Supplies  
MPS-15 Series power supplies are designed specifically to supply power for the Banner  
MICRO-AMP series amplifiers and logic modules. They are constructed on small PC  
boardsthataretrack-mountableforcompatibilitywithothertrack-mountedMICRO-AMP  
components. TheMPS-15includesasocketforaMICRO-AMPamplifierorlogicmodule.  
The combination of an MPS-15 series power supply and a MICRO-AMP module makes  
a complete and compact sensing and/or control system.  
A built-in 5-amp rated SPDT output relay is supplied for easy interfacing to an external  
load or circuit. Its action is controlled by the outputs of a MICRO-AMP module which  
is plugged into the on-board module socket. A switch on the PC board selects which  
module output (normally open or normally closed) will activate the relay.  
Two models are available. Model MPS-15 is for 120V ac operation. Model MPS-15-230  
is for 220/240V ac power. Up to three MICRO-AMP modules may be powered by one  
MPS-15 power supply. A 4-inch (100mm) long mounting track is supplied with each  
MPS-15. Optional 6-inch (150mm) track model TR100-6 neatly accomodates the MPS-  
15 Series PC board plus the PC boards of two additional RS8 sockets to form a complete  
three-module MICRO-AMP sensing/logic system.  
Specifications  
SUPPLYVOLTAGE: modelMPS-15isfor105to130Vac(50/60Hz); relayandtherefore takeadvantageofthe1millisecondresponsetimeof  
model MPS-15-230 is for 210 to 250V ac (50/60Hz).  
the module (see MICRO-AMP module specifications and hookup).  
OUTPUT CONFIGURATION: SPDT electromechanical relay. COMPATIBLEMODULES: modelsMA3,MA3A,MA3-4,MA4-2,  
Contact rating: 250V ac max., 30V dc max., 5 amps max. (resistive MA4G, MA4L, MA5. Donotplugmoduleswithcurrent-sourcingPNP  
load). Install MOV (metal oxide varistor) transient suppressor of ap- outputs (MA3P, MA3-4P, etc.) into the socket on the MPS-15.  
propriate voltage across contacts used to switch inductive loads.  
POWER FOR EXTERNAL DEVICES: 40 milliamps is available  
*Contact response: 20 milliseconds open and close.  
to power external 10 to 30V dc devices (e.g.- two additional MICRO-  
Mechanical life: 10,000,000 operations.  
AMP modules or two MINI-BEAM sensors, etc.).  
*NOTE: dc loads may be easily connected directly to the output(s) of OPERATING TEMPERATURE:  
the MICRO-AMP module used with the chassis in order to bypass the -40 to 70 degrees C (-40 to 158 degrees F).  
Hookup Diagram, MPS-15 & MPS-15-230  
Dimension Drawing, MPS-15 & MPS-15-230  
NOTE: for hookup of sensors or inputs to the module socket,  
see the hookup diagram for the module used.  
Printed in USA  
P?N 03356F3C  
 

ADC Network Card ACE 142S 142V User Manual
Advantech Network Card ADAM 4000 User Manual
Airpura Industries Air Cleaner T600 User Manual
Altec Lansing Portable Stereo System IMT520 User Manual
American Standard Outdoor Shower 3275301 User Manual
AVERATEC GPS Receiver Voya 320 User Manual
Avet Reels Fishing Equipment SX500 User Manual
Avocent Switch CPS1610 CPS User Manual
Bakers Pride Oven Oven GO 36 User Manual
Behringer Microphone MIC200 User Manual