Audiovox Automobile Electronics CMOLF User Manual

Model CMOLF  
License Plate Rearview Camera  
with Selectable Normal/Reverse Image  
CMOLF FEATURES:  
Built Into License Plate Frame  
High Resolution, 1/4” CMOS Color Camera  
Compact Zinc Alloy Die Cast Body  
Waterproof Housing  
Waterproof Microphone  
O
130 WideAngle View  
Selectable Normal/Reverse Image  
128-8104  
1 of 8  
 
Color Camera View:  
Cable Connector End View:  
Normal/Reverse Image Jumper:  
The jumper is located at the camera cable connector. With jumper installed in the harness,  
the camera image will be normal. When the jumper is removed from the harness, the  
camera image will be reversed.  
3
128-8104  
3 of 8  
 
Installation.  
1. Locate suitable location near the vehicles rear license plate to route the camera  
cable. The camera cable can be routed through an existing grommet or use a  
location where a 5/8” hole can be drilled. Be sure to check behind intended drilling  
location. Check for camera interference with license plate lights, hatch release  
switch and/or mechanism.  
2. Remove the screws holding the rear license plate to the vehicle and remove plate.  
3. Place the license plate into the camera license plate frame. If routing camera cable  
into vehicle behind license plate, drill a 5/8-inch hole at selected location. Coat  
edge of hole with rust preventative. Then route the camera cable connector through  
the hole and insert grommet into hole. Place the license plate against vehicle and  
line up the mounting screw holes. Using the black screws provide, tighten the  
screws with the anti-theft tool provided. Pull gently on the camera cable to remove  
slack  
4. If routing camera cable into vehicle above license plate, remove license plate light  
valence. Drill a 5/8-inch hole at selected location. Coat edge of hole with rust  
preventative. Then route the camera cable through the hole and insert grommet  
into hole. Place the license plate against vehicle and line up the mounting screw  
holes. Using the black screws provide, tighten the screws with the anti-theft tool  
provided. Pull gently on the camera cable to remove slack  
4
128-8104  
4 of 8  
 
5. Connect the Camera cable to the extension cable (supplied). Route the extension  
cable up to the intended monitor. Connect as follows:  
a. Black wire- connect to chassis ground  
b. Red wire- connect to 12V accessory wire  
c. Yellow RCA- connect to Video input  
d. Red RCA- connect to audio input (if equipped)  
6. Disregard step 5 if connecting to Audiovox 4-pin camera cable.  
View angle adjustment:  
This camera frame is designed for universal application. The angle of the image of the  
installed frame might have to be adjusted depending on the license plate mounting angle.  
There is a 10-degree angle adjustment wedge supplied to change the downward angle  
from 40 degrees to either 30 or 50 degrees. The angle wedge goes between the camera  
frame and camera body. Longer camera mounting screws are provided for use with the  
angle wedge  
1. Turn on monitor and look at back up camera image. You should be able to see a  
small portion of the vehicles bumper.  
2. If you see too much bumper, the downward angle must be decreased. Place the  
thin edge of the wedge on top between the camera and frame.  
3. If you cannot see the bumper at all, the downward angle must be increased. Place  
the thin edge of the wedge on the bottom between the camera and frame.  
5
128-8104  
5 of 8  
 
Camera Installation  
1. LICENSE PLATE  
2. CAMERA ANGLEADJUSTMENT WEDGE  
3. CAMERA  
6
128-8104  
6 of 8  
 
Specifications:  
1. Power source : DC12V  
2. Current: 50mA  
3. Signal System: NTSC.  
4. Image Device : 1/4” CMOS Sensor.  
5. Horizontal Resolution: 420 lines.  
6. Video Output:1.0Vp-p Composite (75 ohm load).  
7. Minimum Illumination: 0.3LUX  
8. Image Display: Normal or Reverse (Selectable).  
9. Wide Angle View : Diagonal 150° (natural state lens declination 40  
degrees)  
10. Camera Outer Dimensions: 25mm(w) x 30mm(H) x 62mm(D)  
7
128-8104  
7 of 8  
 
© 2006 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
128-8104  
8
128-8104  
8 of 8  
 

Absocold Corp Refrigerator ARD951MW User Manual
Actron Automobile Battery Charger CP7611 User Manual
ADC Network Router Building Entrance Terminals BET User Manual
AGFA Camcorder DV 5000G User Manual
Aiphone Switch KBW M User Manual
Airlink101 Switch ASW208 User Manual
Aiwa CRT Television AV 14F703 User Manual
Allied International Digital Camera V240 User Manual
Allied Telesis Network Card AT 2916T User Manual
Alpine Cooktop PXA H701 User Manual