Audiovox Automobile Electronics 128 8601 User Manual

Model APS-45N  
Owner's Manual  
4 Button Remote Keyless Entry System  
With Two Auxiliary Outputs  
FEATURES:  
2 Four Button, RF Transmitters  
Four Channel Code Learning Receiver  
Remote Panic In All Modes  
Built-In Parking Light Output  
LED Status Indicator  
Ignition Door Locking/Unlocking  
Horn Output  
OPTIONS:  
Remote Trunk Release  
Remote Power Window Control  
Remote Garage Door Interface  
Remote Engine Starter  
Starter Interrupt  
Siren  
Access Guard / 2 Step Unlock  
Illuminated Entry  
Page 1  
128-8601  
1 of 8  
 
Note: If the passive arming mode was selected at time of installation, the dash mounted  
LED will start flashing rapidly indicating that the system is rearming. Opening any  
door will suspend the automatic arming.  
OPTIONAL ACCESS GUARD ( Two Step Unlock )  
If the optional 2-step unlock feature was installed, then only the driver's door will unlock after  
the first press of the unlock button. If you want to unlock all doors, you can simply press the  
unlock button of the keychain transmitter a second time.  
Note: Two Step unlocking is an optional feature that must be wired upon installation.  
VALET / PROGRAM / MANUAL OVERRIDE SWITCH  
The valet switch allows you to temporarily prevent the system from arming, eliminating the  
need to hand your keychain transmitter to parking attendants or garage mechanics. When  
the system is in the valet mode, it will not passively arm or activate the starter interrupt  
circuit. However, all keyless entry features, as well as the remote panic feature will remain  
operational. To enter the valet mode:  
1. Start with the valet switch in the "off" position  
2. Turn the ignition switch to the "on" position.  
3. Flip the valet switch to the "on" position.  
The dash mounted LED will turn on solid (not flashing) indicating that the valet mode has  
successfully been entered.  
To return to the normal mode of operation, move the valet switch to the "off" position at any  
time the ignition switch is in the on position.  
Note: In the event that you lose your keychain transmitter or the transmitter fails to operate  
the keyless entry system, the valet switch can be used to override the optional Starter  
Interrupt, and therefore allow the engine to be started. To override system:  
1. Open the door with the vehicle's door key.  
2. Turn the ignition switch to the on position.  
3. Flip the valet/override switch to the on position. LED will turn on solid.  
The system will disarm, allowing the engine to be started and the vehicle to be operated  
normally. Always remember to move the valet switch to the off position to allow the passive  
arming and optional starter interrupt features to be operable the next time you park the  
vehicle.  
ELIMINATING THE LOCK/UNLOCK CHIRPS  
You can selectively eliminate the normal lock and unlock chirps by holding the transmitter button  
slightly longer when locking and unlocking. This will prevent the horn/siren chirps for one  
lock or unlock cycle. If you find this inconvenient and wish to eliminate these chirps perma-  
nently,  
1. Start with the valet switch in the off position.  
2. Turn the ignition switch "on" then "off".  
3. Within 10 seconds of turning off the ignition, flip the valet switch on, "off", "on", "off",  
"on", "off".  
4. If the chirps were on before you started, the siren will emit 2 short chirps indicating  
that the chirps are now off. If the chirps were off before you started, the siren will  
emit one short chirp indicating that the chirps are now on.  
REMOTE PANIC OPERATION  
The lock or unlock button of your keychain transmitter also serves as a panic button and will  
cause the vehicle horn (or optional siren) to sound on demand. To use the panic feature, you  
must be within the system's maximum operating range. In an emergency situation, to use the  
panic feature, press and hold the lock or unlock button of your keychain transmitter for 3  
seconds. This will cause the lights to flash, the vehicle horn (or optional siren) to sound, and  
if the optional interior illumination circuit was installed, the interior lights to flash. The panic  
mode will continue for 30 seconds and then reset.  
Page 3  
128-8601  
3 of 8  
 
To disengage the panic feature before the 30 seconds are up, press and hold either the lock  
or unlock button of your keychain transmitter for 3 seconds or press the option button  
momentarily. The doors can be unlocked or locked while in "panic" mode by momentarily  
pressing the lock or unlock button respectively.  
ADDITIONAL REMOTE FUNCTION CHANNEL 2  
The system has an additional output, (Channel 2) , that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel are:  
Remote Trunk Release  
Remote Window Close  
To operate the accessory associated with Channel 2, press and hold the option button of  
your keychain transmitter for four seconds.  
NOTE: You may access the Channel 2 command regardless of whether the system is  
"locked" or "unlocked", but not when the ignition switch is in the on position. This  
is to prevent the output from accidentally opening the vehicle's trunk when the  
vehicle is in motion.  
ADDITIONAL REMOTE FUNCTION CHANNEL 3  
The system has an additional output, (Channel 3), that can be connected to a number of  
different optional accessories. Some of the more common uses for this channel are:  
Remote Engine Start  
Remote Window Close  
Remote Garage Door Interface  
To operate the accessory associated with Channel 3, simply press the Option button of your  
keychain transmitter which was configured and programmed for this function.  
NOTE: The channel 3 output will remain active for as long as the transmitter button is  
pressed. Certain accessories may take advantage of the extended output capability  
of this channel. To discontinue the output, simply release the transmitter button.  
IGNITION DOOR LOCKING/UNLOCKING  
The system is capable of being programmed for the added safety and security of ignition  
controlled door locking and unlocking. These features are separate, so the unit may be  
programmed for one, or both, or neither.  
When the ignition door locking feature is programmed, the system will cause all door locks  
to lock whenever the ignition switch is turned from the off to on position, (providing that all  
doors are closed at that time). All doors will lock approximately 3 seconds after the vehicle's  
ignition switch is turned on. This is a nice feature for maintaining the personal safety of the  
occupants of the vehicle, in an effortless and automatic manner.  
When the ignition door unlocking feature is programmed, the system will cause all door locks  
to unlock whenever the ignition switch is turned from the on to off position. All doors will  
unlock immediately after the vehicle's ignition switch is turned off. If 2 Step unlock was  
installed, only the driver's door will unlock.  
As stated these features are programmed separately, so you may chose to use one, both,  
or neither. Please consult with your dealer to consider your options.  
TWO STEP UNLOCK (ACCESS GUARD)  
By pressing the unlock button of the keychain transmitter as you would normally, (Please see  
the section titled "Unlocking The System", earlier in this manual), the system will disarm, and  
only the driver's door will unlock. If however, you should then decide instead that you  
want all doors to unlock, you can simply press the unlock button a second time and all doors  
will unlock.  
Page 4  
128-8601  
4 of 8  
 
PROGRAMMING TRANSMITTERS:  
At times it may become necessary to program replacement or additional transmitters for  
use with your system. To do this:  
1) With the system unlocked or disarmed, turn the ignition key to the on position.  
2) Press and release the Program/Override push-button switch three times  
The unit will flash the parking lights and or beep the horn once to indicate that the system  
is in the transmitter program mode. The LED will also flash one time pause, one time  
pause, etc... indicating that you are in the transmitter program mode of the unit’s channel 1  
or single button program mode.  
3) Press and hold the lock button of each additional transmitter you wish to operate your  
system.  
NOTE: The unit is capable of storing up to 4 transmitters. If a fifth transmitter is added, the  
first transmitter programmed will be bumped out. This unit will also program all 4 buttons of  
your transmitter when the lock button is operated while in the program mode. Once all  
transmitter have been programmed, turn the ignition switch off to exit the program mode.  
If you require priority programming for multiple vehicle operation please read on.  
The system allows priority button programming in case you intend to operate two vehicle  
with one transmitter. In this instance you will program the default button combination,  
(One Button Programming), for the main vehicle you drive, and a different combination for  
the second vehicle so you are not unlocking, locking, or starting both vehicles when they  
are within range of each other.  
To prioritize transmitters after programming the transmitter into the first vehicle:  
Enter the transmitter program of the second vehicle as above by:  
1) With the system unlocked or disarmed, turn the ignition key to the on position.  
2) Press and release the push-button switch three times  
The unit will flash the parking lights and or beep the horn once to indicate that the system  
is in the transmitter program mode. The LED will also flash one time pause, one time  
pause, etc... indicating that you are in the transmitter program mode of the unit’s channel 1  
or single button program mode.  
3) Press and hold any combination of buttons of your transmitter that was not used for  
your primary vehicle.  
If, for instance you can press & hold the lock & unlock buttons simultaneously, for  
controlling Lock function of the second vehicle.  
4) Press and release the program push-button switch once to advance to channel 2,  
unlock.  
Here you can press and hold the lock & start buttons simultaneously, for controlling the  
unlock function of the second vehicle.  
5) Press and release the program push-button switch once to advance to channel 3,  
start.  
Here you can press and hold the start & option buttons simultaneously, for controlling the  
start function of the second vehicle.  
Page 5  
128-8601  
5 of 8  
 
DELETING TRANSMITTERS FROM YOUR SYSTEM:  
It may be necessary to delete a lost transmitter or to reprioritize a transmitter that is  
programmed to your system. To remove a transmitter that has been programmed in your  
system:  
1) Enter the transmitter program mode of channel 1 as indicated above.  
2) Press and hold any transmitter button that has not been programmed into channel 1  
until you hear a chirp, then release and immediately press the same button a second time  
until you hear a long chirp followed by a short chirp. This action erases the transmitter.  
If the transmitter you wish to erase has been lost or stolen then following the information  
below will successfully remove the transmitter.  
NOTE: For this procedure, you must have all transmitters you wish to remain pro-  
grammed in your system available.  
1) Enter the transmitter program mode of channel 1 as indicated above.  
2) Press and hold the lock button of each transmitter you wish to operate the lock  
function of your unit making sure you occupy all 4 transmitter slots. In other words, you  
have three transmitters you wish to remain programmed. Press and hold the lock button  
of transmitter one until a long chirp is heard, then press and hold the lock button of  
transmitter two, then press and hold the lock button of transmitter three, followed by  
pressing and holding the lock button of transmitter one again. This action fills all 4  
receiver slots.  
3) Advance to receiver channel 2 by pressing the push-button switch one time.  
4) Press and hold the unlock button of each transmitter you wish to operate the unlock  
function of your vehicle, again making sure all 4 transmitter slots are filled.  
4) Advance to receiver channel 3 by pressing the push-button switch one time.  
5) Press and hold the unlock button of each transmitter you wish to operate the start  
function of your vehicle, again making sure all 4 transmitter slots are filled.  
If you are uncomfortable about the programming of additional transmitters as outlined in  
the processes above please contact your installation center or call the technical service  
number listed on the back of the transmitter for help.  
BATTERY REPLACEMENT  
The transmitter incorporates a small LED visible through the  
case which is used to indicate battery condition. You will  
notice a decrease in transmitter range as the battery con-  
dition deteriorates. Transmitter battery replacement is  
recommended at least every 10 to 12 months, depending  
upon how frequently the transmitter is used.  
To replace the battery in the 91P Transmitter  
1) Carefully pry apart the case using the edge of a coin as shown.  
2) Remove the rear cover to access the discharged battery paying attention to the proper  
polarity orientation.  
3) Carefully remove and properly dispose of the discharged battery.  
4) Insert the new battery, than carefully snap closed the transmitter case.  
5) If you accidently dislodge the circuit board from the transmitter housing, be certain that  
the rubber membrane is seated properly, and the buttons are properly exposed from the  
front view of the case, then insert the circuit board, and return to step #4.  
91P Uses 2 x CR2016 Lithium Battery  
128-8601  
6 of 8  
 
ORDER FORM FOR 91P  
Attention: Transmitter Ordering Department  
Important: To help us expedite your order, please print all of the information  
legibly  
and mail this form and your payment according to the instructions  
below.  
Note: Transmitter model number found on back of case.  
1) Transmitter Model Number_____________________  
2) Name: _______________________________________  
3) Address: ______________________________________  
4) City: ________________ State: _____ Zip Code: ________  
5) Telephone Number: (_____) _______________  
6) Total Number Of Transmitters Required:  
Cost Per Transmitter is:  
$65.00  
Multiply By Number Of Transmitters  
X ______  
7) Enter Total Amount Enclosed _________________  
(New York State Residents must include the appropriate sales tax)  
8) Method of Payment:  
Mastercard Visa Check or Money Order (do not send cash)  
Make Checks Payable To Audiovox Corporation  
Credit Card Number: _________________________________  
Credit Card Expiration Date: ____ / _____ / _____  
Credit card purchasers can order additional or replacement  
transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and  
follow the instructions from the operator interface.  
9) Mail this form along with your payment to:  
Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y., 11788  
Attn.:TRANSMITTERDEPARTMENT  
128-8601  
7 of 8  
 
Option Button  
Option Button  
Option Button  
Option Button  
Option Button  
Option Button  
Unlock 2  
Unlock 2  
Unlock 2  
Unlock 2  
Unlock 2  
Unlock 2  
Lock 1  
Lock 1  
Lock 1  
Lock 1  
Lock 1  
Lock 1  
APS-45N  
SYSTEM FUNCTIONSATAGLANCE  
LED INDICATORS:  
RAPID FLASHING  
SLOW FLASHING  
=
=
=
=
PASSIVE ARMING  
ARMED  
DISARMED  
VALET MODE  
OFF  
ON SOLID  
OPTIONAL VEHICLE HORN OR SIREN CHIRP INDICATION:  
1 CHIRP  
2 CHIRPS  
CONTINUOUS  
=
=
=
LOCK / ARM  
UNLOCK / DISARMED  
PANIC MODE  
ALARM PARKING LAMP INDICATIONS:  
1 FLASH  
2 FLASHES  
CONTINUOUS FLASH  
=
=
=
LOCK / ARM  
UNLOCK / DISARM  
PANIC MODE  
© 2009 Audiovox Electronics Corp., Hauppauge, NY 11788  
128-8601  
Page 6  
128-8601  
8 of 8  
 

3Com Switch 10005622 User Manual
Adder Technology Switch TS4 User Manual
ADTRAN Network Router HTU Nx64 User Manual
Advantech Webcam MIC 3081 User Manual
AG Neovo Computer Monitor M 17 User Manual
AllerAir Air Cleaner UV 2 Sterilizer User Manual
Alvin Mobility Aid CH445 User Manual
Ativa Paper Shredder LD100 User Manual
Axis Communications Automobile Electronics P14 E User Manual
Beko Refrigerator CDA 565 FS User Manual