American Standard Indoor Furnishings SERIES 7193 User Manual

AMERICAST® BRAND  
SELF RIMMING  
Installation  
Instructions  
LAKELAND™ KITCHEN SINKS  
SERIES 7193  
Thank you for selecting American-Standard...the benchmark of fine quality  
for over 100 years. To ensure that your installation proceeds smoothly--  
please read these instructions carefully before you begin.  
Certified to comply with ANSI A112.19.4.M  
U.S. Patent No. 4,664,982  
Other patents pending.  
CAN/C.S.A. B-45  
Observe local plumbing and building codes.  
Refer to American Standard roughing-in information for  
specific dimensions for each model.  
CUTOUT DIMENSIONS FOR SINKS:  
Below are the dimensions needed to determine the cutout size for your  
installation. Select the correct diagram for your application and refer to the  
instructions below.  
BEFORE YOU BEGIN...  
Unpack new sink and inspect carefully for damage.  
Replace the sink in its original packing carton to  
protect it until you are ready to begin installation.  
Recommended Tools & Materials  
Locate and mark center lines of sink on countertop.  
Silicone Sealant  
Putty Knife  
Pipe Wrench  
Channel Locks  
Phillips Screwdriver  
Regular Screwdriver  
Adjustable Wrench  
Drill  
Provide proper clearance under the countertop for the faucet supply lines and  
the structural parts of the cabinet.  
Basin Wrench  
Saber Saw  
Tubing Cutter  
Tape Measure  
Hacksaw  
By using the diagrams below and measuring your sink, draw the outline of  
the sink onto the countertop. This is not the cutting outline.  
Refer to the diagram for your sink and draw a line the required distance in  
from the sink outline. Cut on this line.  
Mineral Spirits  
COUNTERTOP CUTOUT FOR  
COUNTERTOP CUTOUT FOR  
UNDERCOUNTER INSTALLATIONS  
NEW INSTALLATIONS  
33"  
(838mm)  
27-3/8"  
(695mm)  
CUTOUT  
1" R (25mm) TYP.  
1-5/8" (16mm)  
SINK  
22"  
(559mm)  
2-5/16" R (19mm) TYP.  
16-7/8"  
(429mm)  
SUPPORT  
CLIPS  
OUTLINE  
5/8"  
(16mm)  
CUTTING LINE  
COUNTERTOP MOUNTED FAUCET  
MODEL 7193 UNDER COUNTER MOUNT  
LAKELAND SINGLE BOWL  
LAKELAND SINGLE BOWL  
MODEL 7193 SELF RIMMING  
COUNTERTOP CUTOUT FOR  
REPLACEMENT INSTALLATIONS  
29-1/2"  
(749mm)  
33"  
(838mm)  
CUTOUT  
1" R (25mm) TYP.  
3/4" R (19mm) TYP.  
22"  
(559mm)  
20-1/2"  
(521mm)  
5/8" to 1-5/8"  
(16 to 41mm)  
SUPPORT  
CLIPS  
SINK  
OUTLINE  
5/8"  
(16mm)  
CUTTING LINE  
SINK MOUNTED FAUCET  
MODEL 7193 UNDER COUNTER MOUNT  
LAKELAND SINGLE BOWL  
LAKELAND SINGLE BOWL  
MODEL 7193 SELF RIMMING  
CAUTION:  
1. Recommended Minimum Countertop Thickness Wood 19mm (3/4") Marble and Solid Surface 12mm (1/2")  
2. Prior to cutting countertop ensure that the faucet shank has sufficient length to attach the mounting nut after  
the shank goes through both the countertop and the sink deck. The deck is 10mm (3/8") thick.  
NOTE: Undercounter Installations of sinks should be done by trained and experienced installers due to the materials (such  
as marble, hard synthetics, etc.). Contact your countertop distributor for best method of cutting the opening.  
IMPORTANT: DIMENSION OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN  
THE RANGE OF TOLERANCES ESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS.  
©AMERICAN STANDARD INC. 2005  
791393-100 Rev. A  
 
INSTRUCTIONS FOR UNDERCOUNTER MOUNTED SINK  
WITH COUNTERTOP MOUNTED FAUCET.  
1
2
5
Apply a bead of sealant to  
the edge of the sink. Hold  
the sink against the  
Countertop  
Countertop  
Cutout  
Edge  
Perimeter  
of sink  
Sealant  
under-side of the  
countertop and rotate the  
clips to hold the sink in  
place. Snug the screws to  
hold the sink. Attach all the  
additional clips.  
Cutout  
12mm  
(1/2")  
Drill a clearance hole inside the cutout line  
as marked on the countertop.  
Support Clip  
6
7
Countertop  
Countertop  
Perimeter  
of sink  
Sink  
Surface  
Cutout  
Cut opening on cut line inside the perimeter of sink.  
Mount the faucet and drain assembly  
on the sink or countertop following  
the manufacturer's instructions.  
Note - Formica countertop installation only is illustrated.  
Contact your countertop distributor for the best method of  
cutting other materials such as marble, hard synthetics, etc.  
3
Countertop  
Template  
Countertop  
Sink  
Surface  
Cutout  
Cut faucet holes in the countertop and remove the template.  
CAUTION  
PROPER FIT  
Faucet  
Prior to beveling the  
Connect supply lines to faucet finger tight, and  
carefully bend to engage with the supply stops.Tighten  
connections to faucet for secure seal.  
Escutcheon  
countertop edge, be sure that  
the faucet escutcheon does  
not extend onto the curved  
portion of the countertop.  
Countertop  
4
8
CUTOUT  
Trap  
B
SUPPORT  
CLIPS  
A
Single Bowl  
Attach at least eight of the support clips to the underside  
of the countertop as shown below. The location of the  
clips should be as shown in the sink diagram. The wood  
screws are for use in wood, plywood, or particle board  
(drill appropriate pilot hole). The inserts supplied are for  
use in marble or hard synthetic material.  
Connect drain assembly hand tight to check alignment. It  
may be necessary to cut off part of the tailpiece (area "A")  
or part of the horizontal leg of the trap (area "B").  
Secure joint for watertight assembly.  
3
791393-100 Rev. A  
 
INSTRUCTIONS FOR UNDERCOUNTER MOUNTED SINK  
WITH SINK TOP MOUNTED FAUCET.  
Countertop  
1
2
7
Drill a clearance  
hole inside the  
cutout line as  
marked on the  
countertop.  
Perimeter  
of sink  
Trap  
B
A
Single Bowl  
Cutout  
Cut opening on cut line inside the perimeter of the template.  
Note - Formica  
Countertop  
Connect drain assembly hand tight to check alignment. It  
may be necessary to cut off part of the tailpiece (area "A") or  
part of the horizontal leg of the trap (area "B").  
countertop installation  
only is illustrated. Contact  
your countertop  
Perimeter  
of sink  
distributor for the best  
method of cutting other  
materials such as marble,  
hard synthetics, etc.  
Secure joint for watertight assembly.  
CARE AND CLEANING...  
Cutout  
For all porcelain enamel surfaces, regular, gentle care is best. The  
recommended way to preserve the finish, avoid scratches, and clean  
porcelain enamel fixtures is to rinse them with detergent and water.  
Generally, any of the light duty liquid dishwashing detergents, such as  
Palmolive or Dawn, work well. In areas where the water is hard, a heavy duty  
CUTOUT  
3
4
liquid laundry detergent such as liquid Tide will work better.  
Product names listed herein are trademarks of American Standard Inc.unless otherwise noted.  
®
Palmolive is a registered trademark of Colgate-Palmolive Co.  
SUPPORT  
CLIPS  
®
®
Tide and Dawn are registered trademarks of Procter and Gamble.  
®
AMERICAST LIMITED LIFETIME WARRANTY  
If an American-Standard Americast® brand product is found to be defective in  
materials or workmanship, after inspection by an authorized American-Standard  
representative, American-Standard will repair or, at its option, exchange the product  
for a similar model. This warranty extends for the lifetime of the product, so long as it  
remains in use in its original place of installation, except that the warranty applies to  
a bathing vessel’s slip-resisting surface only for the first year after the product’s initial  
installation.  
This warranty applies only to the original purchaser and installation of these  
products.  
This warranty does not apply to whirlpool components or to faucets, drains,  
mounting rims, grab bars or other accessories. If manufactured or supplied by  
American-Standard, such whirlpool components and accessories are covered under  
separate limited warranties.  
This warranty does not apply to local building code compliance. Since local  
building codes vary considerably, the purchaser of this product should check with a  
local building or plumbing contractor to assure local code compliance before  
installation.  
This warranty shall be void if the Americast® brand product has been moved  
from its initial place of installation; if it has been subjected to faulty maintenance,  
abuse, misuse, accident or other damage; if it was not installed in accordance with  
American-Standard’s instructions; or if it was modified in a manner inconsistent with  
the product as shipped by American-Standard.  
American-Standard's option to repair or exchange the product under this  
warranty does not cover any labor or other costs of removal or installation, nor shall  
American-Standard be responsible for any other incidental or consequential  
damages attributable to a product defect or to the repair or exchange of a  
defective product, all of which are expressly excluded from this warranty.  
(Some states or provinces do not allow the exclusion or limitation of implied  
warranties, so this exclusion may not apply to you.)  
This warranty gives you specific legal rights. You may have other statutory rights that  
vary from state to state or from province to province, in which case this warranty  
does not affect such statutory rights.  
Attach at least eight of the support clips to the underside  
of the countertop as shown below. The location of the  
clips should be as shown in the sink diagram. The wood  
screws are for use in wood, plywood, or particle board  
(drill appropriate pilot hole). The inserts supplied are for  
use in marble or hard synthetic material.  
Countertop  
Cutout  
Apply a bead of sealant to  
the edge of the sink. Hold  
the sink against the  
under-side of the  
countertop and rotate the  
clips to hold the sink in  
place. Snug the screws to  
hold the sink. Attach all  
the additional clips.  
Edge  
Sealant  
12mm  
(1/2")  
Support Clip  
Countertop  
5
6
Mount the faucet and drain  
assembly on the sink or  
countertop following the  
manufacturer's instructions.  
Sink  
Surface  
For service under these warranties, it is suggested that a claim be made through  
the contractor or dealer from or through whom the product was purchased, or that a  
service request (including a description of the product model and of the defect) be  
sent to the following address:  
In the United States:  
American Standard Inc.  
P.O. Box 6820  
Piscataway, New Jersey 08855  
Attention: Director of Consumer Affairs  
For residents of the United States, warranty  
information may also be obtained by calling  
the following toll free number: (800) 442-1902  
Connect supply lines to  
faucet finger tight, and  
carefully bend to  
engage with the supply  
stops.Tighten  
connections to faucet for  
Countertop  
In Mexico:  
In Canada:  
American Standard  
Customer Service Manager  
Ideal Standard, S.A. de C.V.  
Via Morelos #330  
2480 Stanfield Rd.  
Mississauga, Ontario  
Canada L4Y 1S2  
Toll Free: (800) 387-0369  
Col. Santa Clara  
Ecatepec 55540 Edo. Mexico  
secure seal.  
Sink Surface  
Under counter  
4
791393-100 Rev. A  
 

ACCO Brands Paper Shredder RDS 2050 User Manual
Aegis Micro Home Theater System AegisNeo Series User Manual
Agilent Technologies Webcam FS2100 User Manual
Alpine DVD Player DVA 5205 User Manual
Audiovox Automobile Alarm SS91 User Manual
Behringer DJ Equipment LX1B User Manual
Behringer Musical Toy Instrument PH9 User Manual
Beko Air Conditioner LG BKE4500 D LG BKE5505 D User Manual
Beko Refrigerator CF5713AP User Manual
Eureka Tents Tent Nergy Portable Canopy User Manual