Extron electronic Extron Electronics Computer Accessories DVD DL 101 User Manual

DVI DL 101 Setup Guide  
DVI-DUAL LINK INPUT  
DVI DL 101  
DVI DL 101  
POWER  
12V  
DVI-DUAL LINK OUTPUT  
0.2A MAX  
The Extron® DVI DL 101 is a dual link cable equalizer that extends DVI signals beyond the specified cable limits of  
15 feet (5 m). It attaches to the end of a long cable run of up to 275 feet (84 m) for dual link and up to 200 feet (61 m)  
for single link. The DVI DL supports all dual link DVI signals up to 330 MHz, including 2560x1600 or1080p at 60 Hz. It is  
backwards compatible with single link, therefore supporting all single link rates up to 165 MHz, including 1920x1200 and  
1080p at 60 Hz.  
This guide provides basic instructions for an experienced installer to set up and operate this cable equalizer.  
1
8
Installation Procedure  
1. Turn off and disconnect all equipment from the  
9
17  
24  
power source.  
Pin  
1
Pin  
Signal  
Signal  
Pin  
Signal  
2. (Optional) If desired, mount the DVI DL on a 9.5, 6,  
or 3.5 inch deep rack shelf; a projector mounting  
pole; or furniture.  
TMDS data 2–  
9
TMDS data 1–  
17 TMDS data 0–  
18 TMDS data 0+  
2
TMDS data 2+ 10 TMDS data 1+  
3. Connect a DVI source device to the DVI-Dual Link  
3
TMDS data  
2/4 shield  
11 TMDS data 1  
shield  
19 TMDS data 0/5  
shield  
Input DVI-I connector on the front panel.  
4. Connect a DVI output device to the DVI-Dual Link  
4
5
6
TMDS data 4– 12 TMDS data 3–  
TMDS data 4+ 13 TMDS data 3+  
20 TMDS data 5–  
21 TMDS data 5+  
Output DVI-I connector on the rear panel.  
DDC clock  
14 +5 V power  
22 TMDS clock  
shield  
NOTE: Dual link DVI cables must be used for  
dual link DVI signals. If a single link  
DVI cable is used, only single link DVI  
signals are possible.  
7
DDC data  
15 Ground (+5 V)  
23 TMDS clock+  
24 TMDS clock–  
8
CEC control* 16 Hot plug  
detector  
5. Wire the provided power supply as illustrated below  
and connect it to the 2-pole, 3.5 mm captive screw  
connector on the rear panel.  
*CEC control on pin 8 is a proprietary usage, and is not the industry  
standard.  
Table 1. DVI Connector Pin Assignments  
Smooth  
Ridges  
CAUTION: The power supply must not be permanently fixed  
to the building structure or similar structures.  
The power supply must not be located within  
environmental air handling spaces or the wall  
cavity.  
A
A
The installation must be in accordance with the  
applicable provisions of the National Electrical  
Code ANSI/NFPA 70, Article 725 and the Canadian  
Electrical Code, Part 1, Section 16.  
The power supply must be located within the  
same vicinity as the Extron A/V processing  
equipment in an ordinary location, Pollution  
Degree 2, secured to a podium, a desk, or an  
equipment rack within a dedicated closet.  
Tie  
Wrap  
Power Supply  
Output Cord  
3/16” (5 mm)  
MAX  
SECTION A–A  
Captive Screw Connector  
Figure 1. Wiring the Power Connector  
CAUTION: Applying power with incorrect voltage polarity can damage the power supply and equalizer. Identify  
the negative lead by the ridges on the side of the cord. (See the illustration above.)  
CAUTION: Always use a power supply by Extron for the DVI DL 101. Use of an unauthorized power supply voids all  
regulatory compliance certification and may cause damage to the supply and the DVI DL.  
SW4 3G HD-SDI • Setup Guide  
1

Motorola i890 H75XAH6JS5AN User Manual
Motorola i60c User Manual
Kenwood ALL MODE MULTIBANDER TS B2000 User Manual
Huawei Technologies Cell Phone U8800 51 User Manual
HTC EVO 4G PC36100 User Manual
Hamilton Beach D60012 User Manual
Emerson SMARTSET CKS3029C User Manual
Craftsman 79989 User Manual
Avocent Computer Accessories 590 836 501D User Manual
Alpine CDA 9853 User Manual