Actiontec electronic BTHS 6023 User Manual

Wireless  
Bluetooth Headset  
User Manual  
Actiontec Wireless Bluetooth Headset User Manual  
ii  
Introduction  
1
Thank you for purchasing the Actiontec Wireless Bluetooth Headset. The Headset  
allows the user to communicate between various Bluetooth devices, including cel-  
lular phones, personal digital assistants, and laptop computers, using advanced  
voice-recognition technology.  
Important! Please read this entire chapter. It contains important  
safety information.  
Package Contents  
Actiontec Wireless Bluetooth Headset  
Power Adapter  
Installation mini-CD (include User Manual)  
Earpads  
Quick Start Guide  
Accessory bag  
1
Actiontec Wireless Bluetooth Headset User Manual  
Features  
The Headset features two buttons (Large and Small), which have various func-  
tions, as well as two lights (LEDs), red and blue.  
Putting On the Headset  
You can wear the Wireless Bluetooth Headset on either ear. The ear brace is  
detachable from the earpiece section of the Headset. Simply remove it from the  
Headset and set it in the appropriate direction to fit your ear.  
2
Chapter 1 Introduction  
Technical Support  
Actiontec Electronics prides itself on making durable, high-quality, high-perform-  
ance products. If you need assistance, the Actiontec Technical Support Department is  
available 24 hours a day, seven days a week, to provide professional support.  
Actiontec Electronics, Inc.  
760 N. Mary Avenue  
Sunnyvale, CA 94085  
Technical Support  
Phone: 1-888-436-0657  
3
Actiontec Wireless Bluetooth Headset User Manual  
4
Using the Wireless  
Headset  
2
This chapter contains instructions on how to use the Headset, including charging  
the Battery and connecting to a Bluetooth-enabled cellular phone.  
Charging the Battery  
The rechargeable battery included with the Headset is not fully charged when new,  
and must be recharged before using. Recharging the first time takes approximately  
4 hours; afterwards, each full battery recharge will take approximately 2 hours. A  
fully charged battery will provide approximately 3 to 4.5 hours of talk time, and  
100+ hours of standby time. To recharge the battery:  
1. Plug the battery charger into a wall outlet. The green light on the charger will  
illuminate.  
2. Connect the other end of the battery charger into power port on the bottom  
of the Headset. A click is heard when the charger is properly inserted in the  
power port, and the red light on the charger will illuminate.  
3. When the battery is full, the red light will turn off.  
Turning the Headset On/Off  
Turning On  
To turn the Headset on, press and hold the Large Button for three seconds. Two  
short, high-pitched tones will sound, then the blue light on the Headset will illu-  
minate. The Headset is now turned on.  
Note: If the Headset’s rechargeable batter is low, the red light on  
the Headset will flash.  
5
Actiontec Wireless Bluetooth Headset User Manual  
Turning Off  
To turn the Headset off, press and hold the Large Button for three seconds. Two  
short, low-pitched tones will sound, then the red light will flash. When it stops  
flashing, the Headset is turned off.  
Pairing the Headset  
To use the Headset with a cellular phone, it must be paired with the phone. To do  
this:  
1. Press the Large Button for 5 seconds. Two high-pitched tones will sound, fol-  
lowed by two more tones, and then the red and blue lights will flash.  
2. Initiate the pairing procedure on the Bluetooth-enable cellular phone to pair  
with the Headset. Make sure the cellular phone is in discovery mode.  
3. Place the Headset one to three feet from the cellular phone.  
4. When the cellular phone requests a passkey, enter 1234 (the default PIN of  
the Headset). When pairing is successful, the red light will turn off, and the  
blue light will illuminate.  
If the pairing fails, the Headset will turn off automatically after two minutes.  
About Pairing  
Pairing is the process of associating Bluetooth devices with each other. When two  
devices are paired, they establish a permanent, secure link with each other,  
enabling quick access to services provided without having to enter passwords every  
time either device is activated.  
Paired devices remain paired even when one of the devices is not powered up, the  
service connection is stopped or interrupted, or one or both of the devices are  
rebooted.  
6
Chapter 2 Using the Headset  
Handling Calls  
Once the Headset is successfully paired with a cellular phone, you can use it to  
make and receive calls. If your cellular phone suppors voice dialing, you can per-  
form this with the Headset.  
Making Calls  
There are two ways to make a call, using the Headset: keying in the number on the  
cellular phone dial pad, or using voice dialing (if the cellular phone supports this  
feature).  
Using the Dial Pad  
To use the dial pad on the cellular phone, dial the phone number. Once the call  
is placed, the conversation will be carried by the Headset.  
Using Voice Dialing  
To use voice dialing, press the Large Buttone until a beep is heard. Say the name  
of the person to be called. The call is placed.  
Answering/Ending Calls  
When an incoming call is received, a beep is heard, and the blue light will flash  
quickly. To answer:  
1. Press the Large Button.  
2. If needed, adjust the volume. Press the Large Button to increase the volume;  
press the Small Button to decrease the volume.  
3. To end the call, press the Small Button for three seconds, or do nothing. After  
10 seconds, the Headset will automatically disconnect.  
If the Headset if powered off and an incoming call is received, press the Large  
Button for three seconds to answer the call.  
Note: Due to the design of some cellular phones, the Headset  
may auto-disconnect even if it is powered on, and will not beep  
when receiving an incoming call. To reconnect the Headset to the  
cellular phone, press the Large Button for one second.  
7
Actiontec Wireless Bluetooth Headset User Manual  
Connecting to a Computer  
To connect the Headset to a computer, the computer must be Bluetooth-enabled  
(i.e., support Bluetooth internally or have a Bluetooth adapter installed). The com-  
puter must support Audio Gateway Profiles.  
1. Press the Large Button for 5 seconds. Two high-pitched tones will sound, fol-  
lowed by two more tones, and then the red and blue lights will flash.  
2. On the computer, open the Bluetooth Configuration screen and double-  
click Find Bluetooth Devices.  
Note: The Bluetooth Configuration setup may differ based on  
the brand of the Bluetooth adapter you are using.  
3. Place the Headset firmly in either ear.  
4. On the computer, Right-click on the CSR-bc2 icon. From the menu that  
appears, select Pair Device.  
8
Chapter 2 Using the Headset  
5. A new window appears, requesting a passkey to connect to the Headset. Enter  
1234, then press Enter.  
6. The Headset icon turns green. The Headset is successfully connected to the  
computer.  
Connecting to Other Devices  
To connect the Headset to another type of device (a PDA, for example), the device  
must support Audio Gateway Profiles. Refer to the user manual of the other device  
to set up the Headset.  
9
Actiontec Wireless Bluetooth Headset User Manual  
10  
Troubleshooting  
3
This section details problems that may occur when using the Headset, and solu-  
tions for them.  
The Red Light is flashing. What does this mean?  
When only the Red light is flashing, the Headset’s rechargeable battery is run-  
ning low. Plug the Headset into a wall outlet via the power adapter and recharge  
the battery. Full recharge takes approximately two hours.  
I charged the Headset’s battery for 20 minutes, but it still doesn’t work.  
What can I do?  
The Headset’s rechargeable battery must be charged for at least 40 minutes  
before it can be used. It is recommended, however, that the battery be charged  
for the full two hours.  
I plugged the Headset into an electrical socket, but it doesn’t appear to be  
recharging. What’s going on?  
If the Headset hasn’t been used for a long time, or the battery is nearly empty, it  
may take a few minutes for the Red Light to flash and indicate that it is recharging.  
I am getting no sound between the Headset and the device it’s connnected  
to. What should I do?  
Check the following:  
• Make sure the Headset and the device have been paired.  
• Make sure the Headset is turned on.  
• Make sure the Headset and the device are withn working range of  
each other.  
• If connecting to a cellular phone, make sure it has good signal strength.  
• Some cellular phones support only one Bluetooth headset at a time.  
Disconnection can occur if more than one Headset is being used.  
11  
Actiontec Wireless Bluetooth Headset User Manual  
12  
Notices  
Regulatory Compliance Notices  
Class B Equipment  
This equipment has been tested and found to comply with the limits for a Class B  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference in a residential installa-  
tion. This equipment generates, uses, and can radiate radio frequency energy and,  
if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that inter-  
ference will not occur in a particular installation. If this equipment does cause  
harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the  
interference by implementing one or more of the following measures:  
Reorient or relocate the receiving antenna;  
Increase the separation between the equipment and receiver;  
Connect the equipment to an outlet on a circuit different from that to  
which the receiver is connected;  
Consult the dealer or an experienced radio or television technician for help.  
Modifications  
The FCC requires the user to be notified that any changes or modifications made  
to this device that are not expressly approved by Actiontec Electronics, Inc., may  
void the user’s authority to operate the equipment.  
Declaration of conformity for products marked with the FCC logo – United States  
only.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions:  
1. This device may not cause harmful interference;  
13  
Actiontec Wireless Bluetooth Headset User Manual  
2. This device must accept any interference received, including interference that  
may cause unwanted operation.  
Note: To comply with FCC RF exposure compliance require-  
ments, the antenna used for this transmitter must be installed to  
provide a separation distance of at least 20 cm from all persons  
and must not be co-located or operating in conjunction with  
any other antenna or transmitter.  
For questions regarding your product or the FCC declaration, contact:  
Actiontec Electronics, Inc.  
760 North Mary Ave.  
Sunnyvale, CA 94086  
United States  
Tel: (408) 752-7700  
Fax: (408) 541-9005  
14  
Limited Warranty  
Hardware: Actiontec Electronics, Inc., warrants to the end user (“Customer”) that  
this hardware product will be free from defects in workmanship and materials,  
under normal use and service, for twelve (12) months from the date of purchase  
from Actiontec Electronics or its authorized reseller.  
Actiontec Electronics’ sole obligation under this express warranty shall be, at  
Actiontec’s option and expense, to repair the defective product or part, deliver to  
Customer an equivalent product or part to replace the defective item, or if neither  
of the two foregoing options is reasonably available, Actiontec Electronics may, in its  
sole discretion, refund to Customer the purchase price paid for the defective prod-  
uct. All products that are replaced will become the property of Actiontec Electronics,  
Inc. Replacement products may be new or reconditioned. Actiontec Electronics war-  
rants any replaced or repaired product or part for ninety (90) days from shipment,  
or the remainder of the initial warranty period, whichever is longer.  
Software: Actiontec Electronics warrants to Customer that each software program  
licensed from it will perform in substantial conformance to its program specifica-  
tions, for a period of ninety (90) days from the date of purchase from Actiontec  
Electronics or its authorized reseller. Actiontec Electronics warrants the media con-  
taining software against failure during the warranty period. The only updates that  
will be provided are at the sole discretion of Actiontec Electronics and will only be  
available for download at the Actiontec Web site, www.actiontec.com. Actiontec  
Electronics’ sole obligation under this express warranty shall be, at Actiontec  
Electronics’ option and expense, to refund the purchase price paid by Customer for  
any defective software product, or to replace any defective media with software  
which substantially conforms to applicable Actiontec Electronics published specifi-  
cations. Customer assumes responsibility for the selection of the appropriate appli-  
cations program and associated reference materials. Actiontec Electronics makes no  
warranty or representation that its software products will meet Customer’s  
requirements or work in combination with any hardware or applications software  
products provided by third parties, that the operation of the software products will  
be uninterrupted or error free, or that all defects in the software products will be  
corrected. For any third-party products listed in the Actiontec Electronics software  
product documentation or specifications as being compatible, Actiontec  
Electronics will make reasonable efforts to provide compatibility, except where the  
non-compatibility is caused by a “bug” or defect in the third party’s product or  
from use of the software product not in accordance with Actiontec Electronics  
published specifications or user guide.  
15  
Actiontec Wireless Bluetooth Headset User Manual  
THIS ACTIONTEC ELECTRONICS PRODUCT MAY INCLUDE OR BE BUNDLED  
WITH THIRD-PARTY SOFTWARE, THE USE OF WHICH IS GOVERNED BY A SEPA-  
RATE END-USER LICENSE AGREEMENT.  
THIS ACTIONTEC ELECTRONICS WARRANTY DOES NOT APPLY TO SUCH THIRD-  
PARTY SOFTWARE. FOR THE APPLICABLE WARRANTY, PLEASE REFER TO THE  
END-USER LICENSE AGREEMENT GOVERNING THE USE OF SUCH SOFTWARE.  
Obtaining Warranty Service: Customer may contact Actiontec Electronics  
Technical Support Center within the applicable warranty period to obtain warran-  
ty service authorization. Dated proof of purchase from Actiontec Electronics or its  
authorized reseller may be required. Products returned to Actiontec Electronics  
must be pre-authorized by Actiontec Electronics with a Return Merchandise  
Authorization (RMA) number marked on the outside of the package, and sent  
prepaid and packaged appropriately for safe shipment, and it is recommended that  
they be insured or sent by a method that provides for tracking of the package. The  
repaired or replaced item will be shipped to Customer, at Actiontec Electronics’  
expense, not later than thirty (30) days after Actiontec Electronics receives the  
defective product.  
Return the product to:  
(In the United States)  
Actiontec Electronics, Inc.  
760 North Mary Avenue  
Sunnyvale, CA 94085  
Actiontec Electronics shall not be responsible for any software, firmware, informa-  
tion, memory data, or Customer data contained in, stored on, or integrated with  
any products returned to Actiontec Electronics for repair, whether under warranty  
or not.  
WARRANTIES EXCLUSIVE: IF AN ACTIONTEC ELECTRONICS’ PRODUCT DOES  
NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY FOR  
BREACH OF THAT WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF  
THE PURCHASE PRICE PAID, AT ACTIONTEC ELECTRONICS’ OPTION. TO THE  
FULL EXTENT ALLOWED BY LAW, THE FOREGOING WARRANTIES AND REME-  
DIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, TERMS OR  
CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF  
LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES, TERMS OR CONDI-  
TIONS OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, SATISFAC-  
TORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, AND NON-INFRINGE-  
MENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED. ACTIONTEC ELECTRONICS  
16  
Limited Warranty  
NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT  
ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAIN-  
TENANCE OR USE OF ITS PRODUCTS.  
ACTIONTEC ELECTRONICS SHALL NOT BE LIABLE UNDER THIS WARRANTY IF  
ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR  
MALFUNCTION IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUS-  
TOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION  
OR TESTING, UNAUTHORIZED ATTEMPT TO OPEN, REPAIR OR MODIFY THE  
PRODUCT, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE,  
OR BY ACCIDENT, FIRE, LIGHTNING, OTHER HAZARDS, OR ACTS OF GOD.  
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, ACTION-  
TEC ELECTRONICS ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABIL-  
ITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR  
INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF  
ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF  
INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN  
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFOR-  
MANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCT, EVEN IF ACTIONTEC  
ELECTRONICS OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POS-  
SIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACE-  
MENT,OR REFUND OF THE PURCHASE PRICE PAID, AT ACTIONTEC ELECTRON-  
ICS’ OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE  
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL  
PURPOSE.  
Disclaimer: Some countries, states or provinces do not allow the exclusion or limi-  
tation of implied warranties or the limitation of incidental or consequential dam-  
ages for certain products supplied to consumers, or the limitation of liability for  
personal injury, so the above limitations and exclusions may be limited in their  
application to you. When the implied warranties are not allowed to be excluded in  
their entirety, they will be limited to the duration of the applicable written warranty.  
This warranty gives you specific legal rights which may vary depending on local law.  
Dispute Resolution: The customer may contact the Director of Technical Support  
in the event the Customer is not satisfied with Actiontec Electronics’ response to  
the complaint. In the event that the Customer is still not satisfied with the response  
of the Director of Technical Support, the Customer is instructed to contact the  
Director of Marketing. In the event that the Customer is still not satisfied with the  
response of the Director of Marketing, the Customer is instructed to contact the  
Chief Financial Officer and/or President.  
17  
Actiontec Wireless Bluetooth Headset User Manual  
Governing Law: This Limited Warranty shall be governed by the laws of the State  
of California, U.S.A., excluding its conflicts of laws and principles, and excluding  
the United Nations Convention on Contracts for the International Sale of Goods.  
18  

AIPTEK 3D HD DV Camcorder User Manual
Cambo X2 PRO User Manual
Canon KJ20X8 2B IRSD User Manual
Clarion VMA7483 User Manual
Hanns G Car Video System HSG 1081 User Manual
HP (Hewlett Packard) CC330 User Manual
Hypertec N17148NHY User Manual
Iiyama Car Video System E2003WS User Manual
Ikelite Fuji E 900 User Manual
JVC GR FXM38 User Manual