Whirlpool Computer Monitor WGD6200S User Manual

®
Gas Dryer  
PRODUCT MODEL NUMBERS  
OVERALL DIMENSIONS  
WGD6200S  
WGD6400S  
Gas supply: This dryer is equipped for use with  
natural gas. It is designed-certified by CSA  
International for L.P. (propane or butane) gases  
with appropriate conversion. When rigid pipe is  
used it should be 1/2" IPS. When acceptable to the  
gas supplier and local codes, 3/8" approved tubing  
may be used for lengths under 20 feet. For lengths  
over 20 feet, larger tubing should be used. Pipe-  
joint compounds resistant to the action of L.P. gas  
must be used. If local codes permit, it is  
recommended that new flexible metal tubing,  
design-certified by CSA, be used for connecting  
the appliance to the rigid gas supply line. (The gas  
pipe which extends through the lower rear of the  
appliance has 3/8" male pipe thread.) An individual  
manual shutoff valve must be installed within 6  
feet of the dryer in accordance with the National  
Fuel Gas Code ANSI Z223.1.  
43½"  
(110.5 cm)  
22¼"  
(56.5 cm)  
*29¼"  
(74.3 cm)  
29"  
(73.7 cm)  
*Most installations require a minimum  
5" (12.7 cm) clearance behind the  
dryer for the exhaust vent with elbow.  
Electrical: A four-wire or three-wire, single  
phase, 120-volt, 60 Hz, AC-only, electrical supply  
is required on a separate 15 or 20 amp circuit,  
fused on both sides of the line. A time-delay fuse  
or circuit breaker is recommended.  
Exhaust venting: Exhaust your dryer to the  
outside. Four-inch diameter vent is required. Rigid  
or flexible metal exhaust vent must be used. Do  
Not use plastic or metal foil vent. Exhaust outlet  
hood must be at least 12" from the ground or any  
object that may be in the path of the exhaust.  
RECESSED AREA AND CLOSET INSTALLATION  
For closet installation  
with a door, minimum  
ventilation openings in  
3"  
(7.6 cm)  
14" max.  
(35.6cm)  
48 in. 2  
(310 cm2 )  
the top and bottom of  
18"  
(45.7 cm)  
the door are required.  
Louvered doors with  
equivalent air openings  
are acceptable.  
24 in.2  
3"  
(7.6 cm)  
(155 cm2 )  
1"  
(2.5 cm)  
29"  
(73.7 cm)  
5¹⁄₂"  
1" 29¹⁄₄"  
1"  
(14 cm)  
(2.5 cm)(2.5 cm) (74.3 cm)  
B
C
A
A. Recessed area  
B. Side view - closet or confined area  
C. Closet door with vents  
EXHAUST VENTING  
1. Select the route that will provide the straightest and most direct path outdoors. Plan  
the installation to use the fewest number of elbows and turns. When using elbows or  
making turns, allow as much room as possible. Bend vent gradually to avoid kinking.  
Avoid 90° turns.  
2. Determine vent length.  
The maximum length of the exhaust system depends upon:  
• The type of vent (rigid metal or flexible metal).  
• The number of elbows used.  
• Type of hood.  
See the exhaust vent length chart that matches your hood type for the maximum vent  
lengths you can use.  
3. Determine the number of elbows you will need.  
IMPORTANT: Do not use vent runs longer than specified in the Vent Length Chart.  
4"  
(10.2 cm)  
Box hood style  
4"  
(10.2 cm)  
2.5"  
(6.4 cm)  
4"  
(10.2 cm)  
Angled style  
Louvered style  
Vent Length Chart  
Number of  
90° turns  
or elbows  
Type of  
vent  
Box or  
Louvered  
hoods  
Angled  
hoods  
0
1
2
3
4
Rigid metal  
64 ft (20 m)  
58 ft (17.7 m)  
28 ft (8.5 m)  
Flexible metal 36 ft (11 m)  
Rigid metal  
Flexible metal  
54 ft (16.5 m)  
31 ft (9.4 m)  
48 ft (14.6 m)  
23 ft (7 m)  
Rigid metal  
Flexible metal 27 ft (8.2 m)  
44 ft (13.4 m) 38 ft (11.6 m)  
19 ft (5.8 m)  
In the column listing the type of metal vent you are using (rigid metal or flexible metal),  
find the maximum length of metal vent on the same line as the number of elbows.  
Rigid metal  
Flexible metal 25 ft (7.6 m)  
35 ft (10.7 m) 29 ft (8.8 m)  
17 ft (5.2 m)  
Rigid metal  
27 ft (8.2 m)  
21 ft (6.4 m)  
15 ft (4.6 m)  
Flexible metal 23 ft (7 m)  
Because Whirlpool Corporation policy includes a continuous commitment to improve  
our products, we reserve the right to change materials and specifications without notice.  
Dimensions are for planning purposes only. For complete details, see Installation  
Instructions packed with product. Specifications subject to change without notice.  
Ref. W10054080  
05-30-06  
 

Weil McLain Boiler BCP 8S User Manual
White Rodgers Thermostat 1F80 361 User Manual
Winegard TV Antenna HD9075P User Manual
Winegard TV Antenna RP80RTS User Manual
WTB Automobile Parts FLOAT100RLC User Manual
Yamaha CD Player EMX 220VCD User Manual
Zanussi Freezer ZBB 6244 User Manual
Zanussi Freezer ZEUC 2120 User Manual
Zanussi Refrigerator ZRT 1675 User Manual
Zanussi Washer ZWP 581 User Manual