System Sensor Computer Hardware M500S User Manual

inSTaLLaTiOn and mainTenanCe inSTrUCTiOnS  
3825 Ohio Avenue, St. Charles, Illinois 60174  
1-800-SENSOR2, FAX: 630-377-6495  
m500S Supervised Control module  
SpeCifiCaTiOnS  
Normal Operating Voltage:  
Maximum Current Draw:  
Operating Current:  
15 to 32 VDC  
6.5mA (LED On)  
350 µA max., 1 communication every 5 seconds 47k EOL resistor; 485 µA max. (Communicating, NAC Shorted)  
4 VDC  
Maximum NAC Line Loss:  
External Supply Voltage (between Terminals T10 and T11)  
Maximum (NAC):  
Maximum (Speakers):  
Max. NAC Current Ratings:  
Temperature Range:  
Humidity:  
Regulated 24VDC  
70.07 V RMS, 50 W  
For class B wiring system, the current rating is 3A; For class A wiring system, the current rating is 2A  
32˚F to 120˚F (0˚C to 49˚C)  
10% to 93% Non-condensing  
1
Dimensions:  
41/2˝ H × 4˝ W × 1 /4˝ D (Mounts to a 4˝ square by 21/8˝ deep box.)  
Accessories:  
SMB500 Electrical Box; CB500 Barrier  
BefOre inSTaLLing  
figUre 2a. mOdULe mOUnTing  
figUre 2B:  
This information is included as a quick reference installation guide. Refer to  
the control panel installation manual for detailed system information. If the  
modules will be installed in an existing operational system, inform the opera-  
tor and local authority that the system will be temporarily out of service. Dis-  
connect power to the control panel before installing the modules.  
WiTh Barrier:  
NOTICE: This manual should be left with the owner/user of this equipment.  
generaL deSCripTiOn  
M500S Supervised Control Modules are intended for use in intelligent, two-  
wire systems, where the individual address of each module is selected using  
the built-in rotary decade switches. This module is used to switch an external  
power supply, which can be a DC power supply or an audio amplifier (up  
to 80 VRMS), to notification appliances. It also supervises the wiring to the  
connected loads and reports their status to the panel as NORMAL, OPEN,  
or SHORT CIRCUIT. The M500S has two pairs of output termination points  
available for fault-tolerant wiring and a panel-controlled LED indicator. This  
module can be used to replace an M500C module that has been configured for  
supervised wiring operation.  
ISOLATED  
QUADRANT  
COmpaTiBiLiTY reqUiremenTS  
To ensure proper operation, these modules shall be connected to listed com-  
patible system control panels only.  
figUre 1. COnTrOLS and indiCaTOrS:  
C1050-00  
Wiring  
NOTE: All wiring must conform to applicable local codes, ordinances, and reg-  
ulations. When using control modules in nonpower limited applications, the  
System Sensor CB500 Module Barrier must be used to meet UL requirements  
for the separation of power-limited and nonpower-limited terminals and wir-  
ing. The barrier must be inserted into a 4˝×4˝×21/8˝ junction box, and the  
control module must be placed into the barrier and attached to the junction  
box (Figure 2A). The power-limited wiring must be placed into the isolated  
quadrant of the module barrier (Figure 2B).  
1. Install module wiring in accordance with the job drawings and appropri-  
ate wiring diagrams.  
C0909-01  
mOUnTing  
2. Set the address on the module per job drawings.  
The M500S mounts directly to 4-inch square electrical boxes (see Figure 2A).  
The box must have a minimum depth of 21/8 inches. Surface mounted electri-  
cal boxes (SMB500) are available from System Sensor.  
3. Secure module to electrical box (supplied by installer), as shown in  
Figure 2A.  
SS-460-001  
1
I56-3850-002  
 
figUre 5. TYpiCaL Wiring fOr Speaker SUperviSiOn and SWiTChing, nfpa STYLe Y:  
AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM. SEE PANEL INSTALLATION MANUAL FOR DETAILED INFORMATION.  
CONNECT MODULES TO LISTED COMPATIBLE  
CONTROL PANELS ONLY  
WIRES MUST BE  
AUDIO CIRCUIT  
SUPERVISED PER NFPA  
DO NOT LOOP WIRE AROUND TERMINALS  
10 & 11. BREAK WIRE TO ENSURE  
SUPERVISION OF CONNECTIONS.  
( – )  
FROM PANEL OR  
PREVIOUS DEVICE  
CONTROL  
MODULE  
( + )  
AUDIO AMPLIFIER, 70.7 Vrms MAX.  
AMPLIFIER MUST PROVIDE WIRING  
SUPERVISION PER NFPA.  
( – )  
( + )  
) ( –  
) ( +  
SIGNAL LINE CIRCUIT (SLC)  
32 VDC MAX.  
TWISTED PAIR  
( – )  
– ( )  
IS RECOMMENDED  
47K EOL  
RESISTOR  
ELR-47K  
( + )  
( + )  
(–)  
(+)  
MODULE POLARITIES ARE  
SHOWN IN ALARM  
TO NEXT  
DEVICE  
SUPERVISION  
TO NEXT CONTROL MODULE  
LAST MODULE MUST RETURN  
WIRES FOR SUPERVISION  
SPEAKERS MUST BE LISTED FOR FIRE  
PROTECTION. REFER TO THE RELAY CONTACT  
RATING TABLE FOR MAXIMUM LOAD.  
*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.  
C0915-03  
figUre 6. TYpiCaL faULT TOLeranT Wiring fOr Speaker SUperviSiOn and SWiTChing, nfpa STYLe Z:  
AUDIO CIRCUIT WIRING MUST BE TWISTED PAIR AS A MINIMUM. SEE PANEL INSTALLATION MANUAL FOR DETAILED INFORMATION.  
CONNECT MODULES TO LISTED COMPATIBLE CONTROL PANELS ONLY  
AUDIO CIRCUIT  
FROM  
DO NOT LOOP WIRE AROUND TERMINALS  
10 & 11. BREAK WIRE TO ENSURE  
SUPERVISION OF CONNECTIONS.  
WIRES MUST BE  
( – )  
( + )  
PANEL OR  
PREVIOUS  
DEVICE  
SUPERVISED PER NFPA  
CONTROL  
MODULE  
AUDIO AMPLIFIER, 70.7 Vrms MAX.  
( – )  
AMPLIFIER MUST PROVIDE WIRING  
SIGNAL LINE CIRCUIT (SLC)  
32 VDC MAX.  
SUPERVISION PER NFPA.  
( + )  
) ( –  
) ( +  
TWISTED PAIR  
IS RECOMMENDED  
47K EOL RESISTOR  
IS INTERNAL AT  
( – )  
( + )  
( – )  
( + )  
ALL WIRING SHOWN IS SUPERVISED  
AND POWER LIMITED  
TERMINALS 8 & 9  
(–)  
(+)  
TO NEXT  
DEVICE  
BYPASS CAPACITORS: 100µ  
A2143-20 NONPOLARIZED  
<10µA LEAKAGE  
TO NEXT CONTROL MODULE  
LAST MODULE MUST RETURN  
WIRES FOR SUPERVISION  
SUPERVISION  
SPEAKERS MUST BE LISTED FOR  
FIRE PROTECTION. REFER TO THE  
RELAY CONTACT RATING TABLE  
FOR MAXIMUM LOAD.  
MODULE POLARITIES ARE  
SHOWN IN ALARM  
*NOTE: ANY FAULT IN THE POWER SUPPLY IS LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE.  
C0916-03  
SS-460-001  
3
I56-3850-002  
 
WARNING  
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed) state during shipping. To ensure that  
the switch contacts are in their correct state, modules must be made to communicate with the panel before connecting circuits controlled by the module.  
Three-Year LimiTed WarranTY  
System Sensor warrants its enclosed module to be free from defects in materials and  
workmanship under normal use and service for a period of three years from date of  
manufacture. System Sensor makes no other express warranty for this module. No agent,  
representative, dealer, or employee of the Company has the authority to increase or  
alter the obligations or limitations of this Warranty. The Company’s obligation of this  
Warranty shall be limited to the repair or replacement of any part of the module which  
is found to be defective in materials or workmanship under normal use and service  
during the three year period commencing with the date of manufacture. After phoning  
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return Authorization  
number, send defective units postage prepaid to: System Sensor, Repair Department, RA  
#__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a note describing  
the malfunction and suspected cause of failure. The Company shall not be obligated to  
repair or replace units which are found to be defective because of damage, unreasonable  
use, modifications, or alterations occurring after the date of manufacture. In no case shall  
the Company be liable for any consequential or incidental damages for breach of this  
or any other Warranty, expressed or implied whatsoever, even if the loss or damage is  
caused by the Company’s negligence or fault. Some states do not allow the exclusion or  
limitation of incidental or consequential damages, so the above limitation or exclusion  
may not apply to you. This Warranty gives you specific legal rights, and you may also  
have other rights which vary from state to state.  
SS-460-001  
4
I56-3850-002  
©2009 System Sensor  
 

Sennheiser Ventilation Hood EK 500 G2 User Manual
Snapper Chipper SG3000 User Manual
Sony Camcorder CCD TRV 95 E User Manual
Sony Car Stereo System XT P50V User Manual
Sony CD Player SCD X501ES User Manual
Sony Home Theater System 4 130 029 131 User Manual
Star Manufacturing Hot Beverage Maker 11C B User Manual
Sterling Welder 8820027400 User Manual
Sylvania DVD VCR Combo DVR91VG User Manual
Sylvania Flat Panel Television 6632LG User Manual