Sylvania MP3 Docking Station SIP1527 User Manual

MODEL NO. SIP1527  
HOME MUSIC SYSTEM FOR IPHONE AND IPOD  
INSTRUCTION MANUAL  
PLEASE READ BEFORE OPERATING THIS EQUIPMENT  
 
Warnings and Precautions  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO  
RAIN OR MOISTURE.  
This symbol, located on back or bottom of the unit, is intended to alert the  
user to the presence of un-insulated “dangerous voltage” within the products’s  
enclosure that may be of sufficient magnitude to constitute a risk of electric  
shock to persons.  
This symbol, located on back or bottom of the unit, is intended to alert the  
user to the presence of important operating and maintenance (servicing)  
instructions in the literature accompanying the appliance.  
Any use of the controls or an adjustment to the procedures other than those  
specified herein may result in hazardous radiation.  
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE  
OF PLUG TO WIDE SLOT, FULLY INSERT.  
To reduce the risk of electric shock, do not remove cover (or back). There are no  
user-serviceable parts inside. Please refer any servicing to qualified service personnel.  
WARNING: Changes or modifications to this unit not expressly approved by the  
party responsible for compliance could void the user’s authority to operate the  
equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designedo provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the  
equipment off and on, the user is encouraged to try to correct the interference by one or  
more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between he equipment and receiver.  
• Connect he equipment into an outlet on a circuit different from that to which the  
receiver s connected.  
• Consult the dealer or an experienced radio/TV technician for help.  
2
 
Features  
14  
1
2
3
4
5
13  
12  
11  
10  
6
7
9
8
15  
16  
18  
17  
3
 
Features Defined  
1
2
3
4
5
6
POWER Press to power the music system off or on.  
EQ Press to adjust the preset EQ to Rock, Classic, Jazz, Pop, or Normal.  
STOP Press to stop a CD during play.  
VOLUME Turn to adjust the volume.  
SOURCE Press to switch to radio, CD, Aux, or iPod modes.  
SKIP/SEARCH TUNE (+/-)/TIME(+/-) Press to skip between tracks on a docked iPod, iPhone, or  
loaded CD. Press and hold to search through an individual track. Press to tune the FM radio. Press to  
adjust the time when setting the clock or timer.  
7
8
9
MEM/CLK SET Press to set the clock or save a radio station. Press to program a CD.  
DOCK for iPhone and iPod  
REPEAT/MEM– Press to repeat the current track or an entire album/playlist. Press to cycle through  
saved radio stations.  
10 iPod Press to switch to iPod mode.  
11 PLAY/PAUSE/MEM+ Press to play or pause a docked iPhone or iPod or a loaded CD. Press the cycle  
through saved radio stations.  
12 TIMER Press to view, set, and activate or deactivate the timer.  
13 SLEEP Press repeatedly to set the sleep timer or turn the sleep timer off.  
14 OPEN/CLOSE Press to open or close the CD door.  
15 FM WIRE ANTENNA  
16 COMPOSITE VIDEO OUTPUT  
17 DC POWER INPUT  
18 3.5MM AUDIO INPUT  
4
 
Peripheral Defined  
19 POWER Press to power the music system off or on.  
20 TIMER Press to view, set, and activate or deactivate the timer.  
21 iPod Press to switch to iPod mode.  
22 SHUFFLE Press to play tracks in a random order from a docked iPhone or iPod.  
23 DISPLAY Press to view the time when in radio mode.  
24 SKIP/SEARCH Press to skip between tracks on a docked iPod, iPhone, or loaded CD. Press and hold  
to search through an individual track. Press to tune the FM radio. Press to adjust the time when setting  
the clock or timer.  
25 CLK SET Press and hold to set the clock.  
26 MENU/PROG/MEM Press to cycle through menus on a docked iPhone or iPod. Press to program a CD.  
Press to save a radio station as a preset.  
27 CHAPTER/ALBUM/PLAYLIST Press to skip between chapters, albums, and playlists on a docked  
iPhone or iPod.  
28 REPEAT/M– Press to repeat the current track or an entire album/playlist. Press to cycle through  
saved radio stations.  
29 STOP Press to stop a CD during play.  
30 PLAY/PAUSE/M+ Press to play or pause a docked iPhone or iPod or a loaded CD. Press the cycle  
through saved radio stations.  
31 VOLUME Press to adjust the volume.  
32 EQ Press to adjust the preset EQ to Rock, Classic, Jazz, Pop, or Normal.  
33 MENU/SELECT Press to navigate the menu on a docked iPhone or iPod and make selections.  
34 MUTE Press to mute the volume.  
35 SLEEP Press repeatedly to set the sleep timer or turn the sleep timer off.  
36 SOURCE Press to switch to radio, CD, Aux, or iPod modes.  
6
 
Setup  
Power  
Plug the included AC/DC power  
adapter into the DC POWER INPUT on  
the music system and an AC power  
outlet to power the music system.  
Battery Power  
Requires 1, CR2025, battery (pre-  
installed).  
CR2025  
OPEN  
PUSH  
7
 
Clock and Sleep Timer  
Using the Sleep Timer  
Setting the Clock  
1. Press the POWER button to turn  
1. Press the POWER button to turn  
the music system on.  
2. While listening to music in iPod  
mode, radio mode, aux mode, or  
CD mode, press the SLEEP button  
repeatedly to set the sleep timer to  
the desired time.  
2. Press and hold the CLK SET/MEM  
button on the music system.  
“12 Hr” will appear on the display.  
3. Press the SKIP/SEARCH buttons to  
switch between 12 and 24 hour.  
3. After the selected time has  
expired, the music system will  
4. Press the CLK SET/MEM button to  
select 12 or 24 hour.  
The hour will begin to blink on the  
display.  
5. Press the SKIP/SEARCH buttons to  
adjust the hour.  
An “AM” indicator will appear on the  
display when the time is set to the  
AM. A “PM” indicator will appear on  
the display when the time is set to  
the PM.  
6. Press the CLK SET/MEM button to  
set the adjusted hour.  
The minute will begin to blink on the  
display.  
7. Press the SKIP/SEARCH buttons to  
adjust the minute.  
8. Press the CLK SET/MEM button to  
8
 
Timer  
Activating or Deactivating the Timer  
Setting the Timer  
1. Press the POWER button to turn  
1. Press the POWER button to turn  
2. Press the TIMER button.  
2. Press and hold the TIMER button.  
The current timer settings will  
appear on the display.  
“TIMER” will appear on the display,  
indicating the timer is activated.  
3. Press and hold the TIMER button  
while the timer settings are on the  
display.  
3. To deactivate the timer, press and  
hold the TIMER button again until  
“TIMERon the display disappears.  
The “On Timer” hour will begin to  
blink. “On Timer” refers to the time  
that the music system will power on.  
4. Press the SKIP/SEARCH buttons to  
adjust the “On Timerhour. Press  
the TIMER button.  
The “On Timer” minute will begin to  
blink.  
5. Press the SKIP/SEARCH buttons to  
adjust the “On Timer” minute. Press  
the TIMER button.  
6. Press the SKIP/SEARCH buttons to  
the TIMER button.  
blink.  
7. Press the SKIP/SEARCH buttons to  
the TIMER  
the timer.  
8. Follow the instructions for  
Activation or Deactivating the  
Timer.  
9
 
iPod and iPhone  
Docking an iPod and iPhone  
1. Locate the numbered bracket that  
be docked.  
Each included bracket has a number  
on it, indicating which iPhone/iPod  
model that bracket is compatible  
with. See the separate bracket chart  
page to identify which bracket is  
needed.  
2. Push the face of the dock to open  
the dock for iPhone and iPod.  
3. Snap the bracket into place over  
the iPhone/iPod connector in the  
dock for iPhone/iPod.  
4. Connect the iPhone or iPod to  
the connector inside the Dock for  
iPhone/iPod.  
When the tower speaker is plugged  
in, using AC power, the docked  
iPhone or iPod will charge.  
Playing an iPod and iPhone  
1. Follow the instructions for Docking  
an iPod and iPhone.  
2. Press the POWER button to power  
on the music system.  
3. Press the iPod button to switch to  
iPod/iPhone mode.  
“iPod” and an iPod icon will appear  
on the display.  
4. Press the PLAY/PAUSE button  
to begin playing music from the  
docked iPhone or iPod.  
10  
 
CD  
Loading a CD  
Programming a CD  
1. Press the OPEN/CLOSE button  
on the top of the music system to  
open the CD door.  
1. Follow the instructions for Playing  
a CD.  
2. Press the STOP button.  
2. Load a CD into the music system,  
label side facing up.  
The loaded CD must be stopped to  
create a program.  
3. Close the CD door.  
3. Press the MENU/PROG./MEM  
button on the remote.  
Playing a CD  
“PROG” and a number, indicating  
the order in which the next selected  
track will play, will appear on the  
display.  
1. Follow the instructions for Loading  
a CD.  
2. Press the POWER button to power  
the music system on.  
4. Press the SKIP/SEARCH buttons to  
select a track.  
3. Press the SOURCE button to  
switch to CD mode.  
5. Press the MENU/PROG./MEM  
button on the remote to save the  
selected track to the program.  
The track number will appear on the  
display, to the right of the time, when  
the music system is in CD mode.  
6. Repeat steps 4 and 5 to program  
up to 20 tracks to play in the order  
they were selected.  
4. Press the PLAY/PAUSE button to  
begin playing the loaded CD.  
Cancelling a Programmed CD  
1. After programming the CD, press  
the STOP button twice to cancel  
the program.  
11  
 
FM Radio  
Tuning the FM Radio  
Saving an FM Radio Station  
1. Press the POWER button to power  
1. Follow the instructions for Tuning  
the FM Radio.  
the music system on.  
2. Press the SOURCE button to  
2. Press the TUNE +/- buttons to tune  
switch to FM radio mode.  
the FM radio to the desired station.  
“Radio” will appear on the display.  
3. Press and hold CLK SET/MEM  
button on the music system or the  
MENU/PROG./MEM button on the  
remote.  
3. Press the TUNE +/- buttons to tune  
the FM radio.  
Adjust the position of the FM wire  
antenna to improve FM radio  
reception.  
A preset number (P01) will appear on  
the display, indicating which preset  
the current station will be saved to.  
4. Press the TUNE +/- buttons to  
adjust the preset number (P01 -  
P10).  
5. Once the desired preset is selected,  
press the CLK SET/MEM button  
on the music system or the MENU/  
PROG./MEM button on the remote  
to save the current FM radio  
station to the selected preset.  
Playing a Saved Radio Station  
1. Follow the instructions for Tuning  
the FM Radio and Saving an FM  
Radio Station.  
2. Press the MEM or M buttons to  
cycle through saved radio stations.  
12  
 
Video Output  
Connecting Other Digital Audio Devices  
Using the Video Output  
The COMPOSITE VIDEO OUTPUT will only output video from a docked iPhone or  
iPod with video capabilities.  
Requires a composite RCA video cable (not included).  
1. Follow the instructions for Docking an iPod or iPhone and Playing an iPod or  
iPhone  
2. Check your iPod or iPhone video settings to make sure “TV OUT” is set to “ON”  
or “ASK.  
3. Connect a composite RCA video cable to the COMPOSITE VIDEO OUTPUT on  
the music system and a composite video input on a television.  
4. Adjust the connected television to the input setting used when connecting the  
two devices.  
5. Video played through the docked iPod or iPhone will now be output to the  
connected TV.  
3.5mm Audio Input  
Using the 3.5mm Audio Input  
Requires a 3.5mm audio cable (not included).  
1. Connect a 3.5mm audio cable to the 3.5MM AUDIO INPUT on the music system  
and the headphone jack or 3.5mm audio output on an MP3 player or other audio  
source.  
2. Press the POWER button to power on the music system.  
3. Press the SOURCE button to switch to AUX mode.  
4. Use the native controls on the connected MP3 player or other audio source to  
control the music played through the music system.  
13  
 
LIMITED PRODUCT WARRANTY  
This quality product is warranted to be free from manufacturer’s defects in material and workman-ship,  
provided that the unit is used under the normal operating conditions intended by the manufacturer.  
Should you have any problem with this product, please and it is highly recommended to visit our website  
operating manuals and trouble shooting tips on our website which gives you the answer on most of the  
questions you could have in operating the unit.  
TERMS OF WARRANTY  
C.I. Service Dept. warrants this product to be free from defects in materials and workmanship for 90 days on  
parts and 90 days on labor. If you originally purchased your product more than 90 days ago, a repair fee  
may apply.  
Nothing within this warranty shall imply that C.I. will be responsible or liable for any damage to any items  
placed in this product, whether due to any defect of the product, or its use, whether proper or improper.  
EXCLUSIONS  
Save as herein provided, C.I. Service Dept. (Canada) or C.I. Service Dept. (USA), there are no other  
warranties, conditions, representations or guarantees, express or implied, made or intended by C.I. or its  
authorized distributors and all other warranties, conditions, representations or guarantees, including any  
warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation or  
statue is hereby expressly excluded. Save as herein provided, C.I. Service Dept. (Canada) or C.I. Service  
Dept. (USA), shall not be responsible for any damages to persons or property, including the unit itself,  
howsoever caused or any consequential damages arising from the malfunction of the unit and by the  
purchase of the unit, the purchaser does hereby agree to indemnify and save harmless C.I. from any claim  
for damages to persons or property caused by the unit.  
TO OBTAIN REPAIRS UNDER THE TERMS OF THIS WARRANTY  
1. The original purchaser must present a copy of the original bill of sale and the service warranty card.  
2. Any alterations, abuse, misuse, battery corrosion or accidental damage voids the warranty.  
3. The warranty does not cover cabinets and accessories.  
4. No warranty or insurance contained or set out shall apply when damage or repair is caused by power  
failure; damage in transit or when moving the unit; improper power supply; use for commercial or  
industrial purposes; service calls resulting in customer education, etc.  
5. The defective product should be mailed to:  
Canada  
C.I. Service Dept.  
315 Attwell Drive  
U.S.A  
Curtis International Ltd  
2215 Kenmore Avenue, Suite 100  
Toronto, Ontario  
M9W 5C1  
Buffalo, NY 14207  
14207  
For service assistance and product information, please call: 1-800-968-9853.  
If mailing the product, the freight must be prepaid and a money order for $7.00 should be included  
to cover the cost of insurance and the return of the product.  
6. C.I. reserves the right to repair or replace the parts which have become defective.  
Model No.  
Date Purchased  
Serial No.  
is a registered trademark of OSRAM SYLVANIS Inc. used under licence.  
 

SIIG Computer Drive 04 0399B User Manual
Snapper Snow Blower SS5220E User Manual
Soleus Air Air Conditioner PE8 12R 32 User Manual
Sony Cassette Player WM FX261 User Manual
Sony Cordless Telephone IT ID20 User Manual
Sony Switch UH 1000 User Manual
Source Technologies Printer STM57B User Manual
SOYO Computer Hardware SY D6IBA User Manual
Speed Queen Washer Dryer FES17 User Manual
Steren Telephone Accessories 550 020 User Manual