Sony Switch DVS 9000 C User Manual

SDWIVTCHSER-P9RO0CE0SSO0R-PACCK  
DVS9000SF-C  
PRODUCTION SWITCHER PROCESSOR  
DVS-9000  
DVS-9000SF  
BKDS-9160  
BKDS-9470  
BKDS-9161  
MKS-8110SD MKS-8111SD HK-PSU04  
BKDS-9162  
BKDS-9210  
OPERATION MANUAL [English]  
1st Edition  
 
For the customers in Europe (BKDS-9210/9160/9161/9470,  
MKS-8110SD/8111SD, HK-PSU04 only)  
AVERTISSEMENT  
This product with the CE marking complies with the EMC  
Directive (89/336/EEC) issued by the Commission of the  
European Community.  
Compliance with this directive implies conformity to the  
following European standards:  
Afin d’éviter tout risque d’incendie ou  
d’électrocution, ne pas exposer cet  
appareil à la pluie ou à l’humidité.  
• EN55103-1: Electromagnetic Interference (Emission)  
• EN55103-2: Electromagnetic Susceptibility (Immunity)  
This product is intended for use in the following  
Electromagnetic Environment: E4 (controlled EMC  
environment, ex. TV studio).  
Afin d’écarter tout risque d’électrocution,  
garder le coffret fermé. Ne confier  
l’entretien de l’appareil qu’à un personnel  
qualifié.  
Für Kunden in Europa (nur BKDS-9210/9160/9161/9470,  
MKS-8110SD/8111SD, HK-PSU04)  
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die  
EMV-Direktive (89/336/EEC) der EG-Kommission.  
Die Erfüllung dieser Direktive bedeutet Konformität für die  
folgenden Europäischen Normen:  
CET APPAREIL DOIT ÊTRE RELIÉ À LA  
TERRE.  
• EN55103-1: Elektromagnetische Interferenz (Emission)  
• EN55103-2: Elektromagnetische Empfindlichkeit  
(Immunität)  
Dieses Produkt ist für den Einsatz unter die folgende  
elektromagnetische Bedingung ausgelegt: E4 (kontrollierter  
EMV-Bereich, z.B. Fernsehstudio).  
For the customers in Europe (DVS-9000/9000SF only)  
This product with the CE marking complies with both the EMC  
Directive (89/336/EEC) and the Low Voltage Directive (73/23/  
EEC) issued by the Commission of the European Community.  
Compliance with these directives implies conformity to the  
following European standards:  
• EN60950: Product Safety  
• EN55103-1: Electromagnetic Interference (Emission)  
• EN55103-2: Electromagnetic Susceptibility (Immunity)  
This product is intended for use in the following  
Electromagnetic Environment: E4 (controlled EMC  
environment, ex. TV studio).  
Pour les clients européens (BKDS-9210/9160/9161/9470,  
MKS-8110SD/8111SD, HK-PSU04 uniquement)  
Ce produit portant la marque CE est conforme à la Directive  
sur la compatibilité électromagnétique (EMC) (89/336/CEE)  
émise par la Commission de la Communauté européenne.  
La conformité à cette directive implique la conformité aux  
normes européennes suivantes:  
• EN55103-1: Interférences électromagnétiques (émission)  
• EN55103-2: Sensibilité électromagnétique (immunité)  
Ce produit est prévu pour être utilisé dans l’environnement  
électromagnétique suivant: E4 (environnement EMC contrôlé  
ex. studio de télévision).  
Für Kunden in Europa (nur DVS-9000/9000SF)  
Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt  
sowohl die EMV-Direktive (89/336/EEC) als auch die Direktive  
Niederspannung (73/23/EEC) der EG-Kommission.  
Die Erfüllung dieser Direktiven bedeutet Konformität für die  
folgenden Europäischen Normen:  
• EN60950: Produktsicherheit  
• EN55103-1: Elektromagnetische Interferenz (Emission)  
• EN55103-2: Elektromagnetische Empfindlichkeit  
(Immunität)  
Dieses Produkt ist für den Einsatz unter die folgende  
elektromagnetische Bedingung ausgelegt: E4 (kontrollierter  
EMV-Bereich, z.B. Fernsehstudio).  
Periodic inspections  
To guarantee safe long-term operation, periodic inspections  
are recommended. Please contact your Sony representative  
for detailed information about the content and cost of periodic  
inspections.  
Pour les clients européens (DVS-9000/9000SF  
uniquement)  
Ce produit portant la marque CE est conforme à la fois à la  
Directive sur la compatibilité électromagnétique (EMC) (89/  
336/CEE) et à la Directive sur les basses tensions (73/23/  
CEE) émises par la Commission de la Communauté  
européenne.  
La conformité à ces directives implique la conformité aux  
normes européennes suivantes:  
• EN60950: Sécurité des produits  
• EN55103-1: Interférences électromagnétiques (émission)  
• EN55103-2: Sensibilité électromagnétique (immunité)  
Ce produit est prévu pour être utilisé dans l’environnement  
électromagnétique suivant: E4 (environnement EMC contrôlé  
ex. studio de télévision).  
3
 
Table of Contents  
4
Table of Contents  
 
Powerful frame memory functions  
Up to 222 SDTV still frames can be stored in frame  
memory, and up to eight frames can be called up for use  
simultaneously. Frames are called up instantly, making it  
possible to achieve animation effects. Image movement  
and paint functions are also possible. Still pictures from  
frame memory can be stored on the internal hard disk drive  
of the center control panel, and still pictures can be  
imported from and exported to PCs and other external  
devices.  
Overview  
The DVS-9000-C or DVS9000SF-C Switcher Processor  
Pack is a high-performance, multi-function production  
switcher processor for use in an SDTV-format DVS-9000  
video switcher system. It has a wide range of application,  
being usable in studios and the ENG and OB vans of large-  
scale live production systems as well as in postproduction  
editing systems.  
Four-channel DME  
Features  
Installation of an optional DME board set provides four-  
channel DME functionality. You can apply DME wipes,  
processed keys, and a wide variety of other DME  
functions.  
SDTV format support  
This unit supports the 480i/59.94 and 576i/50 formats.  
Optional backup power supply  
Highly expandable system configuration  
Installation of one or two optional HK-PSU04 Power  
Supply Units provides backup power in addition to the  
power supply unit (s) supplied as standard equipment. This  
reduces the risk of power trouble and increases the  
reliability of live broadcast systems.  
By combining option boards, you can configure the  
optimum system for your requirements, selecting the  
number of inputs and outputs and the number of M/E  
banks. The system’s flexibility guarantees its ability to  
meet future expansion requirements.  
Overview of the DVS-9000  
Components  
High-performance keyers  
Each M/E bank is equipped with four high-performance  
keyers that provide the following standard functions.  
• Ability to apply transitions to keyers independently of  
the background  
• Chroma key and color vector keys in each keyer  
• FineKeyTM, and key borders up to 8H  
• Color mixable matte generator available for both key fill  
and key borders  
DVS-9000 Production Switcher Processor  
DVS-9000 Production Switcher Processor main unit.  
This is the main chassis unit of the DVS-9000 Production  
Switcher Processor (size EIA 8RU).  
It is supplied with boards for 2 M/E banks, 17 inputs, and  
24 outputs as standard equipment.  
The following options may be installed to configure  
different systems.  
Simultaneous output of four programs  
Each M/E bank is able to handle four simultaneous  
program outputs, with the ability to apply any of the four  
keys to program output. This gives the system the ability  
to handle a wide range of operating situations, for example  
simultaneous transmission of four programs.  
Option Name  
Maximum number of installable option  
boards  
BKDS-9160  
BKDS-9161  
BKDS-9210  
BKDS-9470  
MKS-8110SD  
MKS-8111SD  
HK-PSU04  
1
1
2
1
3
1
2
Powerful preview functions  
The system supports simultaneous output of look-ahead  
previews (next preview) and key previews, and also  
transition previews.  
Overview  
5
 
     
DVS-9000SF Production Switcher  
Processor  
DVS-9000SF Production Switcher Processor main unit.  
This is the main chassis unit of the DVS-9000SF  
Production Switcher Processor (size EIA 4RU).  
It is supplied with boards for 1 M/E banks, 17 inputs, and  
12 outputs as standard equipment.  
HK-PSU04 Power Supply Unit  
A backup power supply unit. By installing one or two  
backup units in the DVS-9000, or one backup unit in the  
DVS-9000SF, you can back up the system’s power supply.  
The following options may be installed to configure  
different systems.  
Option Name  
Maximum number of installable option  
boards  
BKDS-9162  
BKDS-9210  
BKDS-9470  
MKS-8110SD  
HK-PSU04  
1
1
1
1
1
BKDS-9160 24 Output Board Set  
A 24-output board set. This option is for the DVS-9000  
only. One option set can be installed.  
BKDS-9161 8 Monitor Output Board  
An 8-output board for monitoring input signals. This  
option is for the DVS-9000 only. One option board can be  
installed.  
BKDS-9162 12 Output Connector Board  
A 12-output connector board. This option is for the DVS-  
9000SF only. One option board can be installed.  
BKDS-9210 Mix Effect Board  
A M/E board. Depending on the configuration, up to two  
option boards can be installed in a DVS-9000 system. One  
option board can be installed in a DVS-9000SF system.  
BKDS-9470 DME Board Set  
A 4-channel DME option board set. One option set can be  
installed in either the DVS-9000 or DVS-9000SF.  
MKS-8110SD 17 Input Board  
A 17-input board. Up to option three boards can be  
installed in the DVS-9000. One option board can be  
installed in the DVS-9000SF.  
MKS-8111SD Additional 12 Input Board  
A 12-input expansion board. This option is for the DVS-  
9000 only. One option board can be installed.  
When more than 68 inputs (three MKS-8110SD boards)  
are required, this board can be installed to provide up to 80  
inputs.  
6
Overview  
 
Location and Function of Parts  
DVS-9000 Front Panel  
POWER  
POWER  
POWER  
POWER  
A
B
C
D
Power A, B, C, D switches and status indicator  
POWER A, B, C and D switches and status indicators  
The POWER switches turn the unit on and off. The unit is  
powered on when the POWER switches are on the “?” side,  
and powered off when the POWER switches are on the  
a” side. The status indicators light in green when the unit  
is powered on.  
Depending on the system’s configuration when shipped,  
there may be no optional HK-PSU04 Power Supply Units  
installed. In this case, the only available POWER switches  
are A and B (there are no switches C and D).  
The unit is not powered on until two of the POWER  
switches (A, B, C, and D) are turned on.  
With HK-PSU04 units installed, the system continues to  
function normally as long as any two of the power supply  
units are operating normally.  
Caution  
When installing the HK-PSU04 in your unit, be sure to  
contact your Sony service representative.  
Note  
If a status indicator does not light when you turn a POWER  
switch on, there may be a fault in the power circuits. Turn  
the POWER switch off and contact your Sony service  
representative.  
Location and Function of Parts  
7
 
   
DVS-9000 Rear Panel  
1SWITCHER REMOTE 1 to 4 connectors  
2SWITCHER CTRL connector  
3 EXT connector  
4REF OUT connector  
5SWITCHER DATA connector  
6REF IN connectors  
7DME EXT IN 1 to 4 connectors  
8DME DATA connector  
qaDME REMOTE connector  
qsDME GPI connector  
9DME CTRL connector  
qdSWITCHER GPI connector  
0 DME MONI OUT  
qfTERMINAL connector  
1 to 4 connectors  
1
2
1
2
3
4
1
2
3
4
EXT IN  
MONI OUT  
- AC IN  
- AC IN  
- AC IN  
- AC IN  
A
B
C
D
3
4
DATA  
DATA  
CTRL  
CTRL  
REMOTE  
GPI  
GPI  
REF IN  
REMOTE  
REMOTE  
2
4
REMOTE  
REMOTE  
1
5
REF OUT  
EXT  
3
TERMINAL  
6
7
49  
56  
8
OUT  
69  
1
2
3
4
5
6
7
8
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
70  
2
71  
3
72  
4
73  
74  
75  
7
76  
77  
9
78  
10  
10  
10  
10  
79  
11  
11  
11  
11  
80  
12  
12  
12  
12  
69  
80  
9
IN  
1
5
5
5
5
6
6
6
6
8
8
8
8
13  
13  
13  
13  
14  
14  
14  
14  
15  
15  
15  
15  
16  
16  
16  
16  
17  
17  
17  
17  
1
10  
11  
12  
13  
14  
15  
16  
17  
17  
IN  
1
2
3
4
7
9
18  
34  
IN  
1
2
3
4
7
9
35  
51  
IN  
1
2
3
4
7
9
52  
68  
IN  
1
12  
OUT  
OUT  
OUT  
OUT  
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
8
8
9
9
9
9
10  
10  
10  
10  
11  
11  
11  
11  
12  
13  
24  
12  
12  
12  
U
25  
36  
37  
48  
qjOUTPUTS 1 to 48 connectors  
qgU terminal  
qh-AC IN A, B, C, D connectors  
qkPRIMARY INPUTS 1 to 68 connectors  
qlEXTEND INPUTS 69 to 80 connectors  
w;MONITOR OUTPUTS 49 to 56 connectors  
8
Location and Function of Parts  
 
 
a SWITCHER REMOTE 1 to 4 connectors  
(D-sub 9-pin, RS-422A)  
Used to control the DVS-9000 AUX bus from external  
devices, and to operate the DVS-9000 from editing control  
systems such as the BVE-9100.  
two connectors have a loop-through configuration.  
Signal input to one connector can be output from the other  
connector. If you will not be using the loop-through  
output, be sure to terminate the unused connector with the  
supplied 75terminator.  
Specify the types of connected devices on the center  
control panel.  
g DME EXT IN (Digital Multi Effects External  
input) 1 to 4 connectors (BNC type) (BKDS-9470)  
Connectors for four serial digital video signal inputs.  
Dedicated input for DME external video.  
b SWITCHER CTRL (Switcher Control) connector  
(RJ-45)  
Connect to an Ethernet switch*.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
h DME DATA (Digital Multi Effects Data) connector  
(RJ-45) (BKDS-9470)  
Connect to an Ethernet switch.  
This network is used primarily to control the various  
devices from the center control panel.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
* For information about Ethernet switches that can be used in an DVS-9000  
system, contact your Sony service representative.  
* Ethernet is a trademark of XEROX Corporation.  
Caution  
For more information about Ethernet switch connectors,  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
For detailed information about setting up the Ethernet  
switch, refer to the documentation supplied with the  
Ethernet switch.  
i DME CTRL (Digital Multi Effects Control)  
connector (RJ-45) (BKDS-9470)  
Connect to an Ethernet switch.  
Caution  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
This network is used primarily to control the various  
devices from the center control panel.  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
c EXT (extension) connector (BNC type)  
Used to expand inputs by connecting devices such as an  
HDS-X series routing switcher.  
Caution  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
d REF OUT (reference video output) connector  
(BNC type)  
Output analog sync signals.  
j DME MONI OUT (Digital Multi Effects Monitor  
Output) 1 to 4 connectors (BNC type) (BKDS-9470)  
Connectors for four serial digital video signal outputs.  
These connectors allow you to monitor any desired output  
signal with the DME signal (video, key, or with graphics).  
e SWITCHER DATA connector (RJ-45)  
Connect to an Ethernet switch.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
This network is used primarily for exchange of various  
types of data (key frame effects, snapshots, etc.) and still  
pictures of frame memory.  
k DME REMOTE (Digital Multi Effects Remote)  
connector (D-sub 9-pin, RS-422A) (BKDS-9470)  
When a BKDS-9470 is installed, enables control of DME  
operations from remote devices.  
Caution  
l DME GPI (Digital Multi Effects General Purpose  
Interface) connector (D-sub 25-pin) (BKDS-9470)  
Connect to external devices for input and output of trigger  
signals. Up to eight inputs and eight outputs are possible,  
with input and output conditions set on the center control  
panel.  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
f REF IN (reference signal input) connectors  
(BNC type)  
If you wish to synchronize this unit to an external reference  
signal, input a black burst signal or analog sync signal. The  
Location and Function of Parts  
9
 
m SWITCHER GPI (Switcher General Purpose  
Interface) connector (D-sub 25-pin)  
t MONITOR OUTPUTS 49 to 56 connectors  
(BNC type) (BKDS-9161)  
Connect to external devices for input and output of trigger  
signals. Up to eight inputs and eight outputs are possible,  
with input and output conditions set on the center control  
panel.  
Use these connectors as outputs for primary input monitors  
or as auxiliary outputs for external devices.  
These connectors are effective if you wish to output  
primary inputs with as little delay as possible.  
n TERMINAL connector (D-sub 9-pin, RS-232C)  
This connetor is used for factory adjustments.  
o U (signal ground) terminal  
Connect to the system ground.  
p - AC IN (AC power input) A, B, C, D connectors  
(3-pin)  
Connect to 100 to 240 V AC power supply with the  
optional AC power cords.  
Depending on the system’s configuration when shipped,  
there may be no optional HK-PSU04 Power Supply Units  
installed. In that case, the AC IN C and D connectors is not  
used.  
Caution  
For information about installing an HK-PSU04, contact  
your Sony service representative.  
q OUTPUTS 1 to 48 connectors (BNC type)  
(BKDS-9160)  
These connectors output serial digital signals. They can be  
freely assigned to program output, preview output, AUX  
output and so on.  
There are two BNC connectors for the lower numbers on  
each slot (1 to 4, 13 to 16, 25 to 28, 37 to 40) and one BNC  
connector for the upper numbers (5 to 12, 17 to 24, 29 to  
36, 41 to 48).  
Make output assignments using the center control panel of  
the DVS-9000 system.  
The number of connectors varies depending on the number  
of BKDS-9160 sets installed.  
Refer to the User’s Guide for information about signals  
that may be assigned.  
r PRIMARY INPUTS 1 to 68 connectors (BNC type)  
(MKS-8110SD)  
These connector accept up to 68 serial digital video signal  
inputs. The number of connectors varies depending on the  
number of MKS-8110SD boards installed.  
s EXTEND INPUTS 69 to 80 connectors (BNC type)  
(MKS-8111SD)  
These connectors accept up to 12 expansion serial digital  
video signal inputs.  
Use these connectors when 69 or more inputs are required.  
10  
Location and Function of Parts  
 
DVS-9000SF Front Panel  
POWER  
A
Power A, B switches and status indicator  
POWER  
B
Power A, B switches and status indicators  
The POWER switches turn the unit on and off. The unit is  
powered on when the POWER switches are on the “?” side,  
and powered off when the POWER switches are on the  
a” side. The status indicators light in green when the unit  
is powered on.  
Depending on the system’s configuration when shipped,  
there may be no optional HK-PSU04 Power Supply Unit  
installed. In this case, the only available POWER switch is  
A (there is no switch B).  
The unit is powered on when either of the two POWER  
switches (A or B) is turned on.  
With an HK-PSU04 unit installed, the system continues to  
function normally as long as either of the two power  
supply units is operating normally.  
Caution  
When installing the HK-PSU04 in your unit, be sure to  
contact your Sony service representative.  
Note  
If a status indicator does not light when you turn a POWER  
switch on, there may be a fault in the power circuits. Turn  
the POWER switch off and contact your Sony service  
representative.  
Location and Function of Parts  
11  
 
 
DVS-9000SF Rear Panel  
1EXT connector  
2REF OUT connector  
3SWITCHER CTRL connector  
4SWITCHER DATA connector  
5REF IN connectors  
0DME REMOTE connector  
qaDME GPI connector  
6DME EXT IN 1 to 4 connectors  
7DME DATA connector  
qsSWITCHER GPI connector  
8DME CTRL connector  
qdSWITCHER REMOTE 1 to 4 connectors  
9 DME MONI OUT  
1 to 4  
qfTERMINAL connector  
connectors  
1
2
3
4
1
2
3
4
1
2
3
EXT IN  
MONI OUT  
DATA  
DATA  
CTRL  
CTRL  
REMOTE  
GPI  
GPI  
REF IN  
REMOTE  
2
4
REMOTE  
1
- AC IN  
A
4
5
6
7
8
REF OUT  
EXT  
REMOTE  
REMOTE  
3
TERMINAL  
1
12  
OUT  
OUT  
1
2
2
3
4
5
5
6
7
7
8
8
9
9
10  
11  
11  
12  
12  
SD  
SD  
SD  
SD  
13  
24  
1
3
4
6
10  
1
2
2
3
3
4
4
5
5
6
7
8
9
9
10  
10  
11  
12  
12  
13  
13  
14  
14  
15  
16  
17  
1
- AC IN  
B
17  
IN  
U
1
6
7
8
11  
15  
16  
17  
18  
34  
IN  
qgU terminal  
qjPRIMARY INPUTS 1 to 34 connectors  
qh-AC IN A, B connectors  
qkOUTPUTS 1 to 24 connectors  
* For information about Ethernet switches that can be used in an DVS-9000  
system, contact your Sony service representative.  
a EXT (extension) connector (BNC type)  
Used to expand inputs by connecting devices such as an  
HDS-X series routing switcher.  
For more information about Ethernet switch connectors,  
b REF OUT (reference video output) connector  
(BNC type)  
Output analog sync signals.  
For detailed information about setting up the Ethernet  
switch, refer to the documentation supplied with the  
Ethernet switch.  
c SWITCHER CTRL (Switcher Control) connector  
(RJ-45)  
Connect to an Ethernet switch*.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
Caution  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
This network is used primarily to control the various  
devices from the center control panel.  
12  
Location and Function of Parts  
 
 
d SWITCHER DATA connector (RJ-45)  
Connect to an Ethernet switch.  
i DME MONI OUT (Digital Multi Effects Monitor  
Output) 1 to 4 connectors (BNC type) (BKDS-9470)  
Connectors for four serial digital video signal outputs.  
These connectors allow you to monitor any desired output  
signal with the DME signal (video, key, or with graphics).  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices. This network is used primarily for  
exchange of various types of data (key frame effects,  
snapshots, etc.) and still pictures of frame memory.  
j DME REMOTE (Digital Multi Effects Remote)  
connector (D-sub 9-pin, RS-422A) (BKDS-9470)  
When a BKDS-9470 DME Board Set is installed, use this  
connector to control the unit from an external device.  
Caution  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
k DME GPI (Digital Multi Effects General Purpose  
Interface) connector (D-sub 25-pin) (BKDS-9470)  
Connect to external devices for input and output of trigger  
signals. Up to eight inputs and eight outputs are possible,  
with input and output conditions set on the center control  
panel.  
e REF IN (reference signal input) connectors (BNC  
type)  
If you wish to synchronize this unit to an external reference  
signal, input a black burst signal or analog sync signal.  
The two connectors have a loop-through configuration.  
Signal input to one connector can be output from the other  
connector. If you will not be using the loop-through  
output, be sure to terminate the unused connector with the  
supplied 75terminator.  
l SWITCHER GPI (Switcher General Puropose  
Interface) connector (D-sub 25-pin)  
Connect to external devices for input and output of trigger  
signals. Up to eight inputs and eight outputs are possible,  
with input and output conditions set on the center control  
panel.  
f DME EXT IN (Digital Multi Effects External  
input) 1 to 4 connectors (BNC type) (BKDS-9470)  
Connectors for four serial digital video signal inputs.  
Dedicated input for DME external video.  
m SWITCHER REMOTE 1 to 4 connectors  
(D-sub 9-pin, RS-422A)  
Used to control the DVS-9000SF AUX bus from external  
devices, and to operate the DVS-9000SF from editing  
control systems such as the BVE-9100.  
Specify the types of connected devices on the center  
control panel.  
g DME DATA (Digital Multi Effects Data) connector  
(RJ-45) (BKDS-9470)  
Connect to an Ethernet switch.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
n TERMINAL connector (D-sub 9-pin, RS-232C)  
This connetor is used for factory adjustments.  
Caution  
o U (signal ground) terminal  
Connect to the system ground.  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
p -AC IN (AC power input) A, B connectors (3-pin)  
Connect to 100 to 240 V AC power supply with the  
optional AC power cords.  
Depending on the system’s configuration when shipped,  
there may be no optional HK-PSU04 Power Supply Unit  
installed. In that case, the AC IN B connector is not used.  
h DME CTRL (Digital Multi Effects Control)  
connector (RJ-45) (BKDS-9470)  
Connect to an Ethernet switch.  
The DVS-9000 System is connected in the same way to the  
Ethernet switch to form a network for exchange of signals  
between the devices.  
This network is used primarily to control the various  
devices from the center control panel.  
Caution  
For information about installing an HK-PSU04, contact  
your Sony service representative.  
Caution  
q PRIMARY INPUTS 1 to 34 connectors (BNC type)  
(MKS-8110SD)  
These connector accept up to 34 serial digital video signal  
inputs. The number of connectors varies depending on the  
number of MKS-8110SD boards installed.  
When using a LAN cable: For safety, do not connect to a  
connector for peripheral device wiring that might have  
excessive voltage.  
Location and Function of Parts  
13  
 
r OUTPUTS 1 to 24 connectors (BNC type)  
(BKDS-9162)  
These connectors output serial digital signals. They can be  
freely assigned to program output, preview output, AUX  
output and so on.  
There are two BNC connectors for the lower numbers on  
each slot (1 to 4, 13 to 16) and one BNC connector for the  
upper numbers (5 to 12, 17 to 24) (the BKDS-9162 is  
required 13 to 24).  
Make output assignments using the center control panel of  
the DVS-9000 system.  
Refer to the User’s Guide for information about signals  
that may be assigned.  
14  
Location and Function of Parts  
 
Example System Configuration  
DVS-9000 System Configuration  
The figure below shows the configuration of a DVS-9000  
system.  
The same type of configuration is possible with a DVS-  
9000SF system.  
a)  
a)  
BVE-9100 Editing  
Control System  
Ethernet switch  
Ethernet switch  
DME  
REMOTE  
DME DME  
DATA CTRL  
SWITCHER  
REMOTE  
CTRL  
SWITCHER DATA  
SWITCHER CTRL  
1
2
1
2
3
4
1
2
3
4
EXT IN  
MONI OUT  
-
-
-
-
AC IN  
AC IN  
AC IN  
AC IN  
A
B
C
D
PERIPH  
3
DATA  
DATA  
CTRL  
CTRL  
REMOTE  
GPI  
GPI  
4
REF IN  
REMOTE  
2
4
REMOTE  
REMOTE  
1
5
REF OUT  
EXT  
REMOTE  
3
TERMINAL  
6
7
49  
56  
8
REMOTE  
Reference video  
DATA  
OUT  
69  
1
2
3
4
5
6
7
8
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
MKS-8010 System  
Control Unit  
70  
2
71  
3
72  
4
73  
74  
75  
7
76  
77  
9
78  
10  
10  
10  
10  
79  
11  
11  
11  
11  
80  
12  
12  
12  
12  
69  
80  
9
IN  
1
5
5
5
5
6
6
6
6
8
8
8
8
13  
13  
13  
13  
14  
14  
14  
14  
15  
15  
15  
15  
16  
16  
16  
16  
17  
17  
17  
17  
1
10  
11  
12  
13  
14  
15  
16  
17  
17  
IN  
1
2
3
4
7
9
18  
34  
IN  
b)  
1
2
3
4
7
9
35  
51  
signal  
IN  
1
2
3
4
7
9
52  
68  
IN  
1
12  
OUT  
OUT  
OUT  
OUT  
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
8
8
9
9
9
9
10  
10  
10  
10  
11  
11  
11  
11  
12  
13  
24  
12  
12  
12  
U
25  
36  
37  
48  
BKS-R Series  
HDS-X Series  
DVS-9000-C Switcher  
Processor Pack  
Reference video  
signal  
b)  
DCU-8000 Device Control Unit Pack  
PERIPH  
Reference  
video signal  
b)  
VTR  
DDR  
Audio Mixer  
a) It is recommended that the  
CTRL and DATA LAN networks  
be configured by connecting  
separate Ethernet switches for  
each LAN.  
b) Terminate with the supplied  
75terminators. Terminators  
are supplied in the product  
package.  
Cross cable  
Cable with BNC connectors  
Example System Configuration  
15  
 
   
Flow of Video Signals  
The figure below shows the flow of video signals in a  
DVS-9000 system.  
The flow of signals is the same in a DVS-9000SF system.  
Camera,  
VTR,routing  
switcher  
Monitor  
b)  
Reference video signal  
DME EXT IN  
1 - 4  
DME MONI OUT  
1 - 4  
1
1
2
3
4
1
2
3
4
Monitor  
2
EXT IN  
MONI OUT  
-
-
-
-
AC IN  
AC IN  
AC IN  
AC IN  
A
B
C
D
3
4
DATA  
DATA  
CTRL  
CTRL  
REMOTE  
GPI  
GPI  
REF IN  
REMOTE  
REMOTE  
2
4
REMOTE  
REMOTE  
1
5
REF OUT  
EXT  
3
TERMINAL  
6
MONITOR OUTPUTS  
7
49 - 56  
49  
56  
8
OUT  
69  
1
2
3
4
5
6
7
8
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
SD  
70  
2
71  
3
72  
4
73  
74  
75  
7
76  
77  
9
78  
10  
10  
10  
10  
79  
11  
11  
11  
11  
80  
12  
12  
12  
12  
69  
80  
a)  
9
100 to 240 V AC power supply  
IN  
1
5
5
5
5
6
6
6
6
8
8
8
8
13  
13  
13  
13  
14  
14  
14  
14  
15  
15  
15  
15  
16  
16  
16  
16  
17  
17  
17  
17  
1
PRIMARY INPUTS 1 - 68/  
EXTEND INPUTS 69 - 80  
10  
11  
12  
13  
14  
15  
16  
17  
17  
Camera,  
VTR,routing  
switcher  
IN  
1
2
3
4
7
9
18  
34  
IN  
1
2
3
4
7
9
35  
51  
IN  
1
2
3
4
7
9
52  
68  
IN  
1
OUTPUTS  
1 - 48  
12  
OUT  
OUT  
OUT  
OUT  
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
4
5
5
5
5
6
6
6
6
7
7
7
7
8
8
8
8
9
9
9
9
10  
10  
10  
10  
11  
11  
11  
11  
12  
13  
24  
12  
12  
12  
U
25  
36  
37  
48  
DVS-9000-C Switcher Processor Pack  
Monitor  
VTR  
a) For the AC power cord of the DVS-9000 Production Switcher Processor,  
refer to “Accessories not supplied” (page 18).  
b) Terminate with the supplied 75terminators.  
Terminators are supplied in the product package.  
Video input signal  
Video output signal  
AC power supply  
16  
Example System Configuration  
 
 
Power Supply Unit Status  
Indicators  
The power supply unit status indicators show the status of  
the power supply unit during operation and when the unit  
is powered on. Whenever a power error is detected, it is  
reflected immediately by the indicator.  
Meaning of status indicator displays  
Indicator Status Description  
color  
Steps to take  
Green  
Red  
Lit  
Lit  
Operating normally  
Power supply unit fan Exchange the  
fault  
fan unit  
Not lit  
Power supply unit  
fault  
Exchange the  
power unit  
Notes  
• When the unit is powered on, the status indicators may  
light momentarily in red and a whining sound may be  
heard. This is not a malfunction.When some of the  
power supply units are off and some are on, the status  
indicators of the units which are off may light in red.  
This is not a malfunction.  
• Power all of the installed power supply units on.  
Power Supply Unit Status Indicators  
17  
 
 
Complies with RS-232C standard  
Data transfer rate: 9600 bps  
BNC type, 75Ω  
Specifications  
EXT  
S-BUS data transfer rate: 312/1250 Kbps  
The following specifications show the reference  
performance for this unit and individual option boards/  
modules.  
Reference input and output  
REF IN  
BNC type, 75, with loop-through  
output  
Design and specifications are subject to change without  
notice.  
Analog black burst/analog sync  
BNC type, 75Ω  
Analog sync  
REF OUT  
Signal level ±300 mV ±10%  
Phase variation range  
90H to +90H  
DVS-9000 Production Switcher  
Processor  
General  
Video input  
Power requirements  
Inputs  
17 (BNC type)  
100 to 240 V AC, 50/60 Hz  
Current consumption  
100 V: 8.5 A, 240 V: 4.2A  
Peak inrush current  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
(1) Power ON, current probe method:  
60 A (100 V), 110 A (240 V)  
(2) Hot switching inrush current,  
measured in accordance with  
European standard EN55103-1: 40 A  
(230 V)  
Return loss  
Cable length  
15 dB  
200 m (5C-2V cable, BELDEN8281 or  
equivalent)  
Video output  
Outputs  
24 (BNC type): 1 to 4 and 13 to 16, each  
with 2 outputs  
Operating temperature  
5ºC to 40ºC (41ºF to 104ºF)  
Performance guaranteed temperature  
10ºC to 35ºC (50ºF to 95ºF)  
Storage temperature  
20ºC to +60ºC (4ºF to +140ºF)  
Operating humidity  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
10% to 90%  
Dimensions (w/h/d, excluding projections)  
AC input  
AC IN A, B, C, D  
482×354×520 mm  
3-pin AC connector  
1
(19×14×20 / inches)  
2
Mass  
Approx. 43 kg (9 lb 7 oz)  
Accessories supplied  
75terminator (1)  
Bracket (4)  
Support angle (2)  
Screw (+B4×10) (8)  
Screw (+PSW 4×10) (8)  
Operation Manual (1)  
Installation Manual (1)  
Control connectors  
CTRL  
RJ-45  
Complies with 100Base-TX standard  
RJ-45  
Complies with 100Base-TX standard  
REMOTE 1, 2, 3, 4  
DATA  
D-sub 9-pin, female  
Comply with RS-422A standard  
Data transfer rate: 38.4 Kbps  
D-sub 25-pin, female  
TTL inputs: 8  
Relay contact outputs: 4 (30V AC/DC,  
0.1A)  
Accessories not supplied  
AC power cord (for USA and Canada only) (125 V 10 A  
2.4 m (8 ft)) (Part No.: 1-557-377-11)  
AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft))  
(Part No.: 1-782-929-21)  
GPI  
Open collector outputs: 4  
D-sub 9-pin, female  
TERMINAL  
18  
Specifications  
 
     
Analog sync  
DVS-9000SF Production Switcher  
Processor  
Signal level ±300 mV ±10%  
Phase variation range  
90H to +90H  
General  
Power requirements  
100 to 240 V AC, 50/60 Hz  
Current consumption  
100 V: 5.4 A, 240 V: 2.5 A  
Peak inrush current  
Video input  
Inputs  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
17 (BNC type)  
(1) Power ON, current probe method:  
60 A (100 V), 110 A (240 V)  
(2) Hot switching inrush current,  
measured in accordance with  
European standard EN55103-1: 40 A  
(230 V)  
Return loss  
Cable length  
15 dB  
200 m (5C-2V cable, BELDEN8281 or  
equivalent)  
Video output  
Outputs  
Operating temperature  
12 (BNC type): 1 to 4, each with 2  
outputs  
5ºC to 40ºC (41ºF to 104ºF)  
Performance guaranteed temperature  
10ºC to 35ºC (50ºF to 95ºF)  
Storage temperature  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
20ºC to +60ºC (4ºF to +140ºF)  
Operating humidity  
10% to 90%  
Dimensions (w/h/d, excluding projections)  
AC input  
482×177×520 mm  
AC IN A, B  
3-pin AC connector  
1
(19×7×20 / inches)  
2
Mass  
Approx. 25 kg (5 lb 8 oz)  
Accessories supplied  
75terminator (1)  
Bracket (4)  
Support angle (2)  
Screw (+B4×10) (8)  
Screw (+PSW 4×10) (8)  
Operation Manual (1)  
Installation Manual (1)  
Control connectors  
CTRL  
RJ-45  
Complies with 100Base-TX standard  
RJ-45  
Complies with 100Base-TX standard  
REMOTE 1, 2, 3, 4  
DATA  
D-sub 9-pin, female  
Comply with RS-422A standard  
Data transfer rate: 38.4 Kbps  
D-sub 25-pin, female  
Accessories not supplied  
AC power cord (for USA and Canada only) (125 V 10 A  
2.4 m (8 ft)) (Part No.: 1-557-377-11)  
GPI  
TTL inputs: 8  
AC power cord (for Europe only) (250 V 10 A 2.4 m (8 ft))  
(Part No.: 1-782-929-21)  
Relay contact outputs: 4 (30V AC/DC,  
0.1A)  
Open collector outputs: 4  
D-sub 9-pin, female  
TERMINAL  
EXT  
BKDS-9160 24 Output Board Set  
Complies with RS-232C standard  
Data transfer rate: 9600 bps  
BNC type, 75Ω  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 50 W  
Dimensions (w/h)  
S-BUS data transfer rate: 312/1250 Kbps  
Reference input and output  
REF IN  
BNC type, 75, with loop-through  
output  
OUT board: 317×380 mm  
Analog black burst/analog sync  
BNC type, 75Ω  
1
(12 / ×15 inches)  
REF OUT  
2
Specifications  
19  
 
   
CN board: 274×94 mm  
Output  
Outputs  
7
3
(10 / ×3 / inches) (using 2 boards)  
8
4
12 (BNC type), 1 to 4, each with 2 outputs  
Mass  
Approx. 2 kg (4 lb 6 oz)  
Signal format SMPTE259M-C  
Signal level 0.8 Vp-p ±10%  
Signal transfer rate  
270 Mbps  
Output  
Outputs  
24 (BNC type), 1 to 4 and 13 to 16, each  
with 2 outputs  
Signal format SMPTE259M-C  
Signal level 0.8 Vp-p ±10%  
Signal transfer rate  
270 Mbps  
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is purchased separately)  
BKDS-9210 Mix/Effect Board  
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is purchased separately)  
Power requirements  
12 V DC  
Power consumption  
Max. 80 W  
Dimensions (w/d, excluding projections)  
BKDS-9161 Monitor Output Board  
1
317×380 mm (12 / ×15 inches)  
2
Mass  
Approx. 2 kg (4 lb 6 oz)  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 10 W  
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is  
purchased separately)  
Dimensions (w/d, excluding projections)  
7
3
274×94 mm (10 / ×3 / inches)  
8
4
BKDS-9470 DME Board Set  
Mass  
Approx. 1 kg (2 lb 3 oz)  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 100 W  
Dimensions (w/h)  
Output  
Outputs  
Signal format SMPTE259M-C  
Signal level 0.8 Vp-p ±10%  
Signal transfer rate  
270 Mbps  
8 (BNC type), each with 2 outputs  
DVP board: 317×380 mm  
1
(12 / ×15 inches)  
2
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is purchased separately)  
CA board: 317×380 mm  
1
(12 / ×15 inches)  
2
CN board: 274×94 mm  
7
3
(10 / ×3 / inches) (When used with  
8
4
two boards)  
Approx. 4 kg (8 lb 13 oz)  
BKDS-9162 12 Output Connector  
Board  
Mass  
Remote Control connectors  
CTRL  
RJ-45  
Complies with 100Base-TX standard  
RJ-45  
Complies with 100Base-TX standard  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 5 W  
Dimensions (w/d, excluding projections)  
DATA  
REMOTE  
D-sub 9-pin, female  
Complies with RS-422A standard  
Data transfer rate: 38.4 Kbps  
D-sub 25-pin, female  
7
3
274×94 mm (10 / ×3 / inches)  
8
4
GPI  
Mass  
Approx. 1 kg (2 lb 3 oz)  
TTL inputs: 8  
20  
Specifications  
 
       
Relay contact outputs: 4 (30V AC/DC,  
0.1A)  
Open collector outputs: 4  
MKS-8111SD Additional 12 Input  
Board  
Input  
Inputs  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 10 W  
Dimensions (w/h)  
4 (BNC type)  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
Return loss  
Cable length  
7
3
15 dB  
274×94 mm (10 / ×3 / inches)  
8
4
200 m (5C-2V cable, BELDEN8281 or  
equivalent)  
Mass  
Approx. 1 kg (2 lb 3 oz)  
Input  
Inputs  
Output  
Outputs  
12 (BNC type)  
4 (BNC type)  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
Return loss  
15 dB  
Cable length  
200 m (5C-2V cable, BELDEN8281 or  
equivalent)  
Accessories supplied  
Operation and Installation Guide (1)  
Accessories supplied  
(supplied only when product is purchased separately)  
Operation and Installation Guide (1)  
(supplied only when product is purchased separately)  
MKS-8110SD 17 Input Board  
HK-PSU04 Power Supply Unit  
General  
Power requirements  
12 V DC  
Power consumption  
Max. 10 W  
Power requirements  
100 to 240 V AC, 50/60 Hz  
Power consumption  
100 V: 10 A, 240 V: 5 A  
Peak inrush current  
Dimensions (w/h)  
7
3
274×94 mm (10 / ×3 / inches)  
8
4
(1) Power ON, current probe method:  
60 A (100 V), 110 A (240 V)  
(2) Hot switching inrush current,  
measured in accordance with  
European standard EN55103-1: 40 A  
(230 V)  
Mass  
Approx. 1 kg (2 lb 3 oz)  
Input  
Inputs  
17 (BNC type)  
Signal format SMPTE259M-C  
Signal level 0.8 V p-p ±10%  
Signal tansfer rate  
270 Mbps  
Output power 12 V DC ±0.5V  
Secondary power supply  
Max. 60 A  
Dimensions (w/h/d)  
Return loss  
15 dB  
3
3
5
94×83×396 mm (3 / ×3 / ×15 / inches)  
4
8
8
Cable length  
200 m (5C-2V cable, BELDEN8281 or  
equivalent)  
Mass  
Approx. 3 kg (6 lb 9 oz)  
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is  
purchased separately)  
Accessories supplied  
Operation and Installation Guide (1)  
(supplied only when product is purchased separately)  
Specifications  
21  
 
     
22  
Specifications  
 
The material contained in this manual consists of information  
that is the property of Sony Corporation and is intended solely  
for use by the purchasers of the equipment described in this  
manual.  
Sony Corporation expressly prohibits the duplication of any  
portion of this manual or the use thereof for any purpose other  
than the operation or maintenance of the equipment described  
in this manual without the express written permission of Sony  
Corporation.  
Le matériel contenu dans ce manuel consiste en informations  
qui sont la propriété de Sony Corporation et sont destinées  
exclusivement à l’usage des acquéreurs de l’équipement  
décrit dans ce manuel.  
Sony Corporation interdit formellement la copie de quelque  
partie que ce soit de ce manuel ou son emploi pour tout autre  
but que des opérations ou entretiens de l’équipement à moins  
d’une permission écrite de Sony Corporation.  
Das in dieser Anleitung enthaltene Material besteht aus  
Informationen, die Eigentum der Sony Corporation sind, und  
ausschließlich zum Gebrauch durch den Käufer der in dieser  
Anleitung beschriebenen Ausrüstung bestimmt sind.  
Die Sony Corporation untersagt ausdrücklich die  
Vervielfältigung jeglicher Teile dieser Anleitung oder den  
Gebrauch derselben für irgendeinen anderen Zweck als die  
Bedienung oder Wartung der in dieser Anleitung  
beschriebenen Ausrüstung ohne ausdrückliche schriftliche  
Erlaubnis der Sony Corporation.  
 
Sony Corporation  
B & P Company  
DVS-9000  
(WW)  
Printed in Japan  
2002.07.13  
© 2002  
3-690-433-01 (1)  
Printed on recycled paper  
 

Sennheiser Headphones Set 810 S User Manual
Sharp Fax Machine FO 2150CM User Manual
Snapper Blower ELBX10152BV User Manual
Snapper Lawn Aerator 4560 User Manual
Soleus Air Air Conditioner SG WAC 15ESE User Manual
Sony Car Stereo System XR L240 User Manual
Sony Cassette Player CFM D1 User Manual
Sony Stereo System CMT CQ1 User Manual
SOYO Computer Hardware SY P4X400 User Manual
Subaru Heat Pump 201 User Manual