Sony Security Camera SNC M3 User Manual

3-863-913-11 (1)  
Network Camera  
SNC-M1/M1W/M3/M3W  
Quick Start Guide Network Configuration Using a Router  
The Quick Start Guide briefly explains the connections and settings of the camera for viewing the  
camera image via Internet when connecting to the network using a router.  
For the installation and operations of the camera, please refer to the Installation Manual and the  
User's Guide in the supplied CD-ROM.  
Flowchart of preparations  
Quick Start Guide (this document)  
Installation Manual User’s Guide  
Check the supplied accessories  
Connect the  
camera.  
Set up the  
camera.  
Install the  
camera.  
Use the  
camera.  
and system reguirements.  
System Configuration  
You can monitor the image of the camera via LAN and Internet.  
LAN  
Computer  
Computer  
Computer  
Microphone  
Network Camera  
SNC-M1/M1W  
SNC-M3/M3W  
Modem  
Wireless*  
Internet  
or  
Speaker  
Web browser  
Router  
* Wireless LAN connection is available only for the SNC-M1W and SNC-M3W.  
Notes  
For viewing the camera image via Internet, the global IP address provided by ISP is required.  
The SNC-M1/M1W/M3/M3W network cameras do not support PPPoE. Use a router compliant with PPPoE if you use ISP with PPPoE  
connection.  
© 2004 Sony Corporation  
 
 
Adobe, Acrobat and Acrobat Reader are trademarks of Adobe  
Systems Incorporated in the United States and/or other  
countries.  
All other company and product names are trademarks or  
registered trademarks of the respective companies or their  
respective makers.  
4
Turn on the Power of the Camera  
1
Insert the DC plug of the supplied AC  
power adaptor into the DC IN 5V jack  
on the camera.  
3
Connect the Camera to the Router  
To make the network setting on the camera, connect the  
camera to the router using a commercially available  
network cable. The setting of the camera should be  
performed using the computer connected to the router.  
2
3
Connect the power cord to the AC  
power adaptor.  
Notes  
Plug the power cord to a wall outlet.  
• Before setting, turn on the power of the router and  
computer and connect them to the Internet.  
• Use a commercially available category 5, straight network  
cable.  
Camera  
!
m
5
• The illustrations used in this guide show the SNC-M1  
network camera.  
1 to DC IN 5V  
2 to a wall outlet  
1
Remove the cap of the camera.  
Power cord  
(supplied)  
AC power adaptor  
(supplied)  
3 to the adaptor  
2
3
Connect the network cable to the LAN  
jack on the router.  
4
Check that the POWER indicator  
flashes, then stays lit.  
Connect the network cable to the  
(network) port on the camera.  
POWER indicator  
Camera  
!
m
5
Router  
to  
The camera is now turned on.  
to LAN  
(10BASE-T/  
After connection, place back the cap of the camera.  
100BASE-TX)  
Network cable  
(straight)  
Connect the Camera to the Router / Turn on the Power of the Camera  
3
 
5
Install the IP Setup Program from  
the CD-ROM  
4
5
Click “Next.”  
This section explains how to install the IP Setup Program  
from the CD-ROM supplied with the camera. The IP Setup  
Program is required for detecting the camera.  
The other supplied programs can be installed in the same  
procedures.  
Click.  
Utility programs stored in the CD-ROM  
The following utility programs are stored in the supplied  
CD-ROM.  
Program  
Function  
Read theSoftwareLicenseAgreement  
carefully and click “Yes” to accept the  
agreement.  
IP Setup Program  
Allows detection and set up of Sony  
network cameras in the network.  
SNC Audio upload tool Allows output of the sound picked up  
by the microphone connected to the  
computer from the speaker built in  
the SNC-M1/M1W/M3/M3W network  
camera.  
Easy recording software  
An easy-recording software program, “Network Camera  
Recorder,is available for the SNC-M1/M1W/M3/M3W  
network cameras.  
Click.  
"Network Camera Recorder" allows manual or scheduled  
recordings of camera images and the sound picked up by the  
microphone built in the camera.  
For more information on “Network Camera Recorder,access  
URL: (for customers in Europe)  
6
Select the destination folder in which  
to install the program and click “Next.”  
The default setting is “C:\…\SONY\IP Setup  
Program.”  
1
2
Insert the CD-ROM disc into the CD-  
ROM drive of your computer.  
Click the “IP Setup” icon of IP Setup  
Program.  
1 The  
destination  
folder is  
displayed.  
Click.  
2 Click.  
3
Click “Open.”  
The IP Setup Program starts and Welcome dialog  
appears.  
Note  
If you click “Save this program to disk,” you cannot install  
correctly.  
In this case, delete the downloaded file, and click the “IP  
Setup” icon again.  
Install the IP Setup Program from the CD-ROM  
4
 
7
Enter or select the name of the folder  
in which to install the program, then  
click “Next.”  
1
2
Start the IP Setup Program.  
Select “Program” from the “Start” menu of  
Windows, then select “IP Setup Program.”  
The default setting is “IP Setup Program.”  
The IP Setup Program runs and displays all the  
cameras connected to the network in the camera  
list.  
1Enter the  
folder name.  
Click on the camera in which you want  
to assign an IP address.  
When multiple cameras are connected to the  
same network, check the model name and serial  
number on the rear of the camera.  
2Click.  
The program is installed. After the installation,  
“Setup Complete” dialog is displayed.  
Click on the camera to assign an IP address.  
8
Click “Finish.”  
Click.  
The IP Setup Program installation is completed.  
The network settings for the selected camera are  
displayed.  
3
Click on “Obtain an IP address  
automatically.”  
By selecting “Obtain an IP address automatically,”  
the IP address is automatically assigned by the  
DHCP server. The “Subnet mask” and “Default  
gateway” are also assigned.  
6
Set up the Camera  
To connect the camera to a network, you need to assign a  
new IP address to the camera. This section explains how  
to assign an IP address to the camera using the installed  
IP Setup Program and how to configure other network  
settings.  
Select this.  
IP address is displayed.  
Notes  
• For viewing the camera image via Internet, the global IP  
address provided by ISP is required.  
• This section explains the usual settings using “Obtain an IP  
address automatically” or “Use the following IP address,”  
“Obtain DNS server address automatically” and “HTTP port  
No. 80.If you need other settings, refer to the User’s Guide  
stored in the supplied CD-ROM.  
Subnet mask is  
displayed.  
Defaultgateway  
is displayed.  
Set up the Camera  
5
 
To assign a static IP address  
8
Click “OK.”  
“Setting OK” is displayed.  
Click on “Use the following IP address” and enter  
the IP address, subnet mask and default gateway.  
The network setting of the camera is completed.  
4
Click on “Obtain DNS server address  
automatically.”  
By selecting “Obtain DNS server address  
automatically,” the DNS server addresses are  
automatically assigned.  
Note  
To exit the IP Setup Program, click  
corner.  
on the upper right  
Select this.  
DNS server addresses are displayed.  
Click.  
7
Set Port Forwarding on the Router  
To view the camera image via Internet, you need to set  
port forwarding on the router. Skip this setting when you  
do not use the router.  
5
6
Click on “80” on “HTTP port No.”  
Select this.  
1
2
Perform the port forwarding setting on  
the router.  
For details, refer to the operation manual supplied  
with the router.  
Type “admin” in both the  
“Administrator name” and  
“Administrator password” boxes.  
The default settings of both items are “admin.”  
You can change the administrator name and  
password later using the “User setting” menu.  
Check the global IP address for WAN  
on the router and record it in the  
following space.  
You need to enter the global IP address when you  
access the camera via Internet.  
Type “admin.”  
Type “admin.”  
Global IP address  
Note  
The name of the function “port forwarding” may be different  
depending on the router.  
7
Record the set IP address in the  
following space.  
You need to enter the IP address when you set  
the router*.  
IP address  
* To view the camera image via Internet, you need to set  
port forwarding on the router. See “Set Port Forwarding  
Set Port Forwarding on the Router  
6
 
 
8
Monitor the Image of the Camera  
3
Click “Enter.”  
You can monitor the image of the camera using Internet  
Explorer as the Web browser.  
Note  
Click.  
This section uses illustrations of the Welcome page of  
Network Camera SNC-M1W.  
Accessing from Internet Explorer  
The image shot by the camera is displayed in the  
main viewer.  
1
2
Start Internet Explorer.  
Type the IP address in the URL box of  
Internet Explorer.  
To view the image via LAN:  
Enter the IP address recorded in step 7 on page  
To view the image via Internet:  
Enter the global IP address of the router recorded  
When you access the main viewer of the camera for  
the first time  
When you click “Enter” on the welcome page, “Security  
warning” is displayed.  
When you click "Yes" to install the ActiveX control and the  
main viewer is displayed.  
Type the IP address.  
The welcome page of the camera is displayed.  
Note  
For checking your network configuration, see “System  
Click.  
Note  
If the welcome page is not displayed correctly, check the  
security level setting of the Internet Explorer. For details, refer  
to the User’s Guide stored in the supplied CD-ROM.  
Monitor the Image of the Camera  
7
 
 
Setting for Wireless Network  
(SNC-M1W/M3W only)  
4
Click “Network.”  
To use the camera in a wireless network via an access  
point, set as follows.  
Click.  
Use the network cable for connection when you assign a  
new IP address to the SNC-M1W/M3W wireless network  
camera.  
The “Network setting” menu appears.  
1
2
Display the welcome page of the  
camera following the procedure of  
5
6
Click the “Wireless network” tab.  
Set the items for the wireless network.  
Click “Setting.”  
1 Infrastructure  
2 SSID  
3 WEP key  
data  
Click.  
4 OK  
a Select “Infrastructure” on “Type.”  
b Enter the “SSID” to match the setting on the  
3
Type the user name and password for  
the administrator, then click “OK.”  
The default settings of both items are “admin.”  
access point.  
c Enter the “WEP key data” to match the  
settings on the access point.  
d Click “OK.”  
Type the user name.  
Type the password.  
7
8
Turn off the power of the camera.  
Remove the network cable from the  
camera.  
Click.  
9
Turn on the power of the camera  
without connecting the network cable.  
The Wireless setting is now enabled.  
The “Administrator” menu is displayed.  
Sony Corporation  
 

Sennheiser Work Light 830S User Manual
Snapper Lawn Aerator 4556 User Manual
Solid State Logic Music Mixer Soundscape Mixer User Manual
Sony Camera Lens VCL ES06A User Manual
Sony Cell Phone LT26i User Manual
Sony Radio HK PSU04 User Manual
Sony Speaker System SMS 2P User Manual
Soundstream Technologies Headphones VHP 9002 User Manual
Sprint Nextel Network Router U301 User Manual
StarTechcom Computer Hardware usb32hdes User Manual