Sony Network Router HKJ 101 User Manual

i.LINK INTERFACE BOARD  
HKJ-101  
INSTALLATION MANUAL  
1st Edition  
 
For the customers in the USA  
For the customers in Europe  
This equipment has been tested and found to comply with  
the limits for a Class A digital device, pursuant to Part 15  
of the FCC Rules. These limits are designed to provide  
reasonable protection against harmful interference when  
the equipment is operated in a commercial environment.  
This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in  
accordance with the instruction manual, may cause  
harmful interference to radio communications. Operation  
of this equipment in a residential area is likely to cause  
harmful interference in which case the user will be  
required to correct the interference at his own expense.  
This product with the CE marking complies with the EMC  
Directive (89/336/EEC) issued by the Commission of the  
European Community.  
Compliance with this directive implies conformity to the  
following European standards:  
EN55103-1: Electromagnetic Interference (Emission)  
EN55103-2: Electromagnetic Susceptibility (Immunity)  
This product is intended for use in the following  
Electromagnetic Environment:  
E1 (residential), E2 (commercial and light industrial), E3  
(urban outdoors) and E4 (controlled EMC environment,  
ex. TV studio).  
Pour les clients européens  
You are cautioned that any changes or modifications not  
expressly approved in this manual could void your  
authority to operate this equipment.  
Ce produit portant la marque CE est conforme à la  
Directive sur la compatibilité électromagnétique (EMC)  
(89/336/CEE) émise par la Commission de la  
Communauté Européenne.  
La conformité à cette directive implique la conformité aux  
normes européennes suivantes:  
The shielded interface cable recommended in this manual  
must be used with this equipment in order to comply with  
the limits for a digital device pursuant to Subpart B of Part  
15 of FCC Rules.  
EN55103-1: Interférences électromagnétiques  
(émission)  
EN55103-2: Sensibilité électromagnétique (immunité)  
Ce produit est prévu pour être utilisé dans  
lenvironnement électromagnétique suivant: E1  
(résidentiel), E2 (commercial et industrie légère), E3  
(urbain extérieur) et E4 (environnement EMC contrôlé ex.  
studio de télévision).  
The device complies with part 15 of the FCC Rules.  
Operation is subject to the following two conditions: (1)  
this device may not cause harmful interference, and (2)  
this device must accept any interference received,  
including ineterference that may cause undesired  
operation.  
Für Kunden in Europa  
For customers in Canada  
Dieses Produkt besitzt die CE-Kennzeichnung Und erfüllt  
die EMV-Richtlinie (89/336/EWG) EG-Kommission.  
Angewandte Normen:  
This Class A digital apparatus complies with Canadian  
ICES-003.  
Pour les utilisateurs au Canada  
Cet appareil numérique de la classe A est conforme à la  
EN55103-1: Elektromagnetische Verträglichkeit  
(Störaussendung)  
norme NMB-003 du Canada.  
EN55103-2: Elektromagnetische Verträglichkeit  
(Störfestigkeit),  
für die folgenden elektromagnetischen Umgebungen:  
E1 (Wohnbereich), E2 (kommerzieller und in  
beschränktem Maße industrieller Bereich), E3  
(Stadtbereich im Freien) und E4 (kontrollierter EMV-  
Bereich, z.B. Fernsehstudio)  
HKJ-101  
1 (P)  
 
 
Section 1  
Installation  
1-1. Overview  
The i.LINK interface board HKJ-101 enables the Digital Video Cassette Compact Player J-H1/J-H3 to  
output the down-converted SD video signal in the i.LINK/DV format.  
In addition, off-line editing can be executed by connecting the J-H1/J-H3 containing the HKJ-101 board  
to the PC containing the non-linear editing software, using an i.LINK/DV cable.  
HKJ-101 consists of the followings.  
. DV-29 board :  
. CN-2478 board :  
1
1
. Rear panel for J-H1 : 1  
. Rear panel for J-H3 : 1  
Beside this Installation Manual, the following manuals are prepared for HKJ-101.  
. Operation Manual CD-ROM (Supplied with J-H1/J-H3)  
This manual is necessary for practical application and operation of J-H1/J-H3 and HKJ-101.  
. Operation Guide (Supplied with J-H1/J-H3)  
This manual serves as a quick reference.  
. J-H Series Maintenance Manual (e-manual) (Available on request)  
This manual describes the information that premises the component service (periodic inspection, ,  
periodic maintenance, diagnostics, parts replacement, adjustments, parts list, block diagrams, schematic  
diagrams, board layouts and others) to be used by system and maintenance engineers.  
If this manual required, please contact your local Sony Sales Office/Service Center.  
1-2. Installing the Circuit Board  
Procedure is different when installing HKJ-101 in J-H1 and J-H3.  
. To install HKJ-101 in J-H1 (Refer to Section 1-2-1.)  
. To install HKJ-101 in J-H3 (Refer to Section 1-2-2.)  
n
Before starting installation, be sure to turn off the POWER switch and disconnect the power cord. Then  
start the following procedures.  
HKJ-101  
1-1 (E)  
 
1-2-1. To install HKJ-101 in J-H1  
5. Insert the CN-2478 board to the second slot from the  
bottom of J-H1.  
1. Remove the six M3 case stopper screws.  
2. Remove the rear panel.  
n
6. Strongly push the connector panel both from the right  
and the left sides of the CN-2478 board so that the  
connector on the CN-2478 board is securely inserted  
into the connector on the MB-993 board.  
Store the removed rear panel in a safe place so as not  
to lose it.  
Rear panel  
M3 case stopper  
screws  
CN-2478 board  
M3 case stopper screws  
7. Install the supplied rear panel for J-H1 using the six  
M3 case stopper screws.  
3. Insert the connector (CN601) on the DV-29 board into  
the connector (CN41) on the CN-2478 board.  
n
n
Tighten the screws in the state that the two dowels are  
aligned with the holes (a) and (b) on the rear panel as  
shown in the figure.  
First, insert the connector (CN401) on the DV-29  
board to the hole for i.LINK connector on the IF panel.  
Then insert connector (CN601) to the connector on the  
CN-2478 board.  
Dowel  
M3 case stopper  
screws  
4. Fix the DV-29 board to the IF panel and to the CN-  
2478 board using the supplied screws (PWH2 x 5 : 2  
screws, PSW2.6 x 5 : 3 screws).  
n
When tightening the screws, tighten the screws PWH2  
Hole (b)  
x 5 first of all screws.  
DV-29 board  
CN401  
Dowel  
M3 case stopper  
screws  
Hole (a)  
M3 case stopper  
screws  
J-H1 rear panel  
(Supplied accessory)  
CN601  
IF panel  
PWH2 x 5  
CN41  
PSW2.6 x 5  
CN-2478 board  
PSW2.6 x 5  
HKJ-101  
1-2 (E)  
 
1-2-2. To install HKJ-101 in J-H3  
4. Insert the connector (CN601) on the DV-29 board into  
the connector (CN41) on the SDI-80 assembly.  
n
1. Remove the six M3 case stopper screws.  
2. Remove the rear panel.  
n
First, insert the connector (CN401) on the DV-29  
board to the hole for i.LINK connector on the IF panel.  
Then insert connector (CN601) to the connector on the  
CN-2478 board.  
Store the removed rear panel in a safe place so as not  
to lose it.  
5. Fix the DV-29 board to the IF panel and to the SDI-80  
assembly using the supplied screws (PWH2 x 5 : 2  
screws, PSW2.6 x 5 : 3 screws).  
Rear panel  
n
When tightening the screws, tighten the screws PWH2  
x 5 first of all screws.  
DV-29 board  
CN401  
M3 case stopper  
screws  
CN601  
M3 case stopper screws  
IF panel  
PWH2 x 5  
CN41  
3. Pull out the SDI-80 assembly from the second slot  
from the bottom of the J-H3 in the direction of the  
arrow.  
PSW2.6 x 5  
SDI-80 assembly  
PSW2.6 x 5  
6. Insert the SDI-80 assembly to the original slot.  
7. Strongly push the connector panel both from the right  
and the left sides of the SDI-80 assembly so that the  
connector on the SDI-80 assembly is securely inserted  
into the connector on the MB-993 board.  
SDI-80 assembly  
SDI-80 assembly  
HKJ-101  
1-3 (E)  
 
8. Install the supplied rear panel for J-H3 using the six  
M3 case stopper screws .  
n
Tighten the screws in the state that the two dowels are  
aligned with the holes (a) and (b) on the rear panel as  
shown in the figure.  
Dowel  
M3 case stopper  
screws  
Hole (b)  
Dowel  
M3 case stopper  
screws  
Hole (a)  
J-H3 rear panel  
(Supplied accessory)  
M3 case stopper  
screws  
HKJ-101  
1-4 (E)  
 
The material contained in this manual consists of  
information that is the property of Sony Corporation.  
Sony Corporation expressly prohibits the duplication of  
any portion of this manual or the use thereof for any  
purpose other than the operation or maintenance of the  
equipment described in this manual without the express  
written permission of Sony Corporation.  
Le matériel contenu dans ce manuel consiste en  
informations qui sont la propriété de Sony Corporation.  
Sony Corporation interdit formellement la copie de  
quelque partie que ce soit de ce manuel ou son emploi  
pour tout autre but que des opérations ou entretiens de  
l’équipement à moins d’une permission écrite de Sony  
Corporation.  
Das in dieser Anleitung enthaltene Material besteht aus  
Informationen, die Eigentum der Sony Corporation sind.  
Die Sony Corporation untersagt ausdrücklich die  
Vervielfältigung jeglicher Teile dieser Anleitung oder den  
Gebrauch derselben für irgendeinen anderen Zweck als  
die Bedienung oder Wartung der in dieser Anleitung  
beschriebenen  
Ausrüstung  
ohne  
ausdrückliche  
schriftliche Erlaubnis der Sony Corporation.  
HKJ-101  
 
Printed in Japan  
2003. 7 16  
©2003  
Sony Corporation  
HKJ-101 (SY) J, E  
3-805-991-01  
B&P Company  
 

Servis Refrigerator AMERICAN STYLE FRIDGE FREEZER User Manual
Servis Switch FS 1004MT User Manual
Sharp Flat Panel Television 52LE920UN User Manual
Shibaura Lawn Mower GT161 User Manual
Shure Car Satellite Radio System PA821 User Manual
Shure Microphone PG58BTS User Manual
Sony Cassette Player WM FX290W User Manual
SOYO Computer Hardware SY K7VEMPRO User Manual
Tandberg Data Network Card Internal USB version User Manual
Tanita Stereo System PD640 User Manual