Sony Computer Monitor GXD L52H1 User Manual

PROFESSIONAL FLAT DISPLAY MONITOR  
GXD-L52H1  
PROTOCOL MANUAL  
1st Edition  
 
Table of Contents  
1. Communication Parameters ......................................................... 1  
2. Pin Assignment..................................................................................... 1  
3. Communication Data Format ....................................................... 1  
4. General Function ................................................................................. 3  
5. Analog Signal Detect Function ................................................... 8  
6. Priority Signal Select Function ................................................... 9  
7. Picture/Sound ...................................................................................... 14  
8. Size/Shift ................................................................................................. 17  
9. Status Enquiry ..................................................................................... 20  
10. User Reset.............................................................................................. 25  
11. Service...................................................................................................... 25  
GXD-L52H1  
 
 
1. Communication Parameters  
3. Communication Data Format  
(a) Control message  
Communication method  
Synchronous method  
Baud rate  
RS-232C  
Asynchronous  
9600bps  
8bit  
No.  
Item  
Value  
1
Header  
0x8C: Control  
0xXX  
Character length  
Parity  
2
Category  
Function  
Data1 (Length)  
Data2 (Data1)  
:
None  
3
0xXX  
Start bit length  
Stop bit length  
Flow control  
1bit  
4
0xXX  
1bit  
5
0xXX  
None  
:
0xXX  
:
:
0xXX  
X
DataX  
0xXX  
2. Pin Assignment  
X+1  
Check Sum  
0xXX  
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a  
value exceeds 255 (1byte).  
Monitor side (D-sub 9-pin)  
Host side (D-sub 9-pin)  
* Set the command interval to 500 ms or more when transmitting the  
Control command continuously.  
5
4
3
2
1
5
4
3
2
1
* Set the command interval to 500 ms or more when transmitting the same  
command (Enquiry) after the Control command.  
9
8
7
6
9
8
7
6
_ External view _  
_ External view _  
(b) Enquiry message  
Pin No. Function  
Pin No. Function  
No.  
Item  
Value  
1
2
3
4
5
6
7
8
9
NC  
TXD  
RXD  
NC  
1
2
3
4
5
6
7
8
9
NC  
RXD  
TXD  
NC  
1
2
3
4
5
6
Header  
0x83: Enquiry  
0xXX  
Category  
Function  
Data1  
0xXX  
GND  
NC  
GND  
NC  
0xFF  
NC  
NC  
Data2  
0xFF  
NC  
NC  
Check Sum  
0xXX  
NC  
NC  
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a  
value exceeds 255 (1byte).  
GXD-L52H1  
1
 
(c) Answer message  
4 Error answer  
1 Control answer  
No.  
Item  
Value  
No.  
1
Item  
Value  
1
2
Header  
Answer  
0xE0: Answer  
Header  
Answer  
0x70: Answer  
*
0x00: No Function Error  
0x01: Check Sum Error  
0x02: Data Length Error  
0xXX  
*
2
0x00: Completed  
0x01: Limit Over  
0x02: Limit Under  
0x03: Command Canceled  
0xXX  
3
Check Sum  
* 0x00: No Function Error  
0x01: Check Sum Error  
0x02: Data Length Error  
Packet header,category or function code are  
not included in this protocol.  
Check sum value or received packet is not  
correct.  
Packet is correctly received,but the data size  
is over the upper limit.  
3
Check Sum  
* 0x00: Completed  
0x01: Limit Over  
Packet is correctly received and process  
is also correctly completed.  
Packet is correctly received, but the data  
value is over the upper limit.  
0x02: Limit Under  
Packet is correctly received, but the data  
value under the lower limit.  
0x03: Command Canceled  
Packet is correctly received, but the data  
value is not correct or the request cannot  
be accepted in the current host state.  
Sum total of 1 to X. Lower one-byte data  
is validated when a value exceeds 255  
(1byte).  
* Check Sum:  
2 Enquiry answer (Complete)  
No.  
Item  
Value  
1
Header  
Answer  
0x70: Answer  
2
0x00: Completed  
3
Return Data Size 0xXX  
4
Return Data1  
0xXX  
0xXX  
0xXX  
0xXX  
0xXX  
:
:
:
:
X
Return DataX  
Check Sum  
X+1  
* 0x00: Completed Packet is correctly received and process is also  
correctly completed.  
* Return Data:  
Returns the read value.  
* Check Sum:  
Sum total of 1 to X. Lower one-byte data is validated  
when a value exceeds 255 (1byte).  
3 Enquiry answer (Command cancel)  
No.  
Item  
Value  
1
2
3
Header  
0x70: Answer  
Answer  
0x03: Command Canceled  
0x73  
Check Sum  
0x03: Command Canceled  
Packet is correctly received, but the data  
value is not correct or the request cannot  
be accepted in the current host state.  
GXD-L52H1  
2
 
4. General Function  
(a) Mode Control  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
Enquiry  
0x8C  
0x83  
0x00  
Code Table (1-a) [a]  
0x02  
0xFF  
Code Table (1-a) [b]  
0xFF  
0xXX  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Code Table (1-a) [b]  
Check Sum  
0xXX  
Enquiry  
0x70  
0x00  
0x02  
Completed  
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x00  
0x01  
Power  
0x00 OFF  
Yes  
Yes  
Enable  
Enable  
0x01 ON  
*4  
Input Select  
0x08 HD15 RGB  
0x09 HD15 YUV  
0x0E OPTION RGB  
0x0F OPTION COMPONENT  
0x20 DVI  
Yes  
Yes  
Disable  
Enable  
0x30 VIDEO  
0x31 S-VIDEO  
0x44 HDMI  
0x84 Option Digital1 (HDMI1/SDI)  
0x85 Option Digital2 (HDMI2)  
0x02  
0x03  
0x04  
Force Status Display 0x00 ON  
0x01 OFF  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
Audio Mute  
0x00 OFF  
0x01 ON  
0x00 ON  
0x01 OFF  
Auto Status Display  
(Continued)  
GXD-L52H1  
3
 
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x06  
Color System  
0x00 Auto  
Yes  
Yes  
Disable  
Enable  
0x01 NTSC  
0x02 NTSC4.43  
0x03 PAL  
0x05 PAL-M  
0x06 PAL-N  
0x07 PAL60  
0x0F  
Language  
0x00 Japanese  
0x01 English  
0x02 Deutsch  
0x03 Français  
0x04 Español  
0x05 Italiano  
0x01-0xFF  
Yes  
Yes  
Disable  
Enable  
0x10  
0x12  
Index Number  
Standby Power  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
0x00 Standard  
0x01 Low  
0x13  
ECO Mode  
0x00 Off  
Yes  
Yes  
Disable  
Enable  
(Power Saving)  
0x01 ECO High  
0x02 ECO Low  
0x00 ON  
0x14  
0x18  
0x1B  
0x24  
Speaker Out  
Sync Mode  
Yes  
Yes  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
0x01 OFF  
0x00 H/Comp  
0x01 Video  
Clock Display  
0x00 OFF  
0x01 ON  
Input Detect  
(Option)  
0x00 FW12 (HD15)  
0x02 FW11 (BNC)  
0x03 Reserved  
0x05 FW50 (RGB)  
0x06 FW21 (UART + CTRL-S)  
0x08 FW15 (HDMI x 2)  
0x09 FW16 (HD-SDI)  
0x0A Reserved  
0x0B Reserved  
0x0C Reserved  
0x0D Reserved  
0x0E Reserved  
0x0F Not Connect  
(Continued)  
GXD-L52H1  
4
 
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x26  
0x27  
0x30  
Auto Shut OFF  
0x00 OFF  
Yes  
Yes  
Yes  
Yes  
Disable  
Enable  
0x01 ON  
Auto Screen Adjust  
PAP  
0x00 OFF  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
0x01 ON  
0x00 OFF  
0x01 P&P  
0x02 PinP  
0x31  
Active Picture  
0x00 Left (P&P)/Main (PinP)  
0x01 Right (P&P)/Sub (PinP)  
0x02 Swap  
Yes  
Yes  
Disable  
Enable  
0x32  
0x33  
Picture Size (P&P)  
0x00-0x0E  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
Sub Picture Size  
(PinP)  
0x00 Large  
0x01 Small  
0x34  
Picture Position  
(PinP)  
0x00 Position1  
Yes  
Yes  
Disable  
Enable  
0x01 Position2  
0x02 Position3  
0x03 Position4  
0x35  
PAP Input Detect  
(Left/Main)  
0x08 HD15 RGB  
0x09 HD15 YUV  
0x0E OPTION RGB  
0x0F OPTION COMPONENT  
0x20 DVI  
No  
Yes  
Disable  
Enable  
0x30 VIDEO  
0x31 S-VIDEO  
0x44 HDMI  
0x84 Option Digital1 (HDMI1/SDI)  
0x85 Option Digital2 (HDMI2)  
0x08 HD15 RGB  
0x09 HD15 YUV  
0x0E OPTION RGB  
0x0F OPTION COMPONENT  
0x20 DVI  
0x36  
PAP Input Detect  
(Right/Sub)  
No  
Yes  
Disable  
Enable  
0x30 VIDEO  
0x31 S-VIDEO  
0x44 HDMI  
0x84 Option Digital1 (HDMI1/SDI)  
0x85 Option Digital2 (HDMI2)  
(Continued)  
GXD-L52H1  
5
 
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x40  
0x41  
Screen Saver  
0x00 OFF  
Yes  
Yes  
Disable  
Enable  
0x01 All White ON  
0x02 Sweep ON  
0x00 Gray  
BackGround  
Yes  
Yes  
Disable  
Enable  
0x01 Dark Gray  
0x02 Black  
0x43  
0x44  
Back Light  
0x00-0x64  
Yes  
Yes  
Yes  
Yes  
Disable  
Enable  
Enable  
Enable  
Logo Illumination  
0x00 Logo Off  
0x01 Logo On (Low)  
0x02 Logo On (High)  
0x00 Main + Remocon  
0x01 Main  
0x45  
Control Mode  
Yes  
Yes  
Disable  
Enable  
0x02 Remocon  
0x03 All Off  
*5  
0x04 Limited  
0x46  
0x47  
On Off Timer Mode  
On Timer Enable  
0x00 Every Day (Repeat)  
0x01 Day Of Week  
Yes  
Yes  
Yes  
Yes  
Enable  
Enable  
Enable  
Enable  
bit0  
bit1  
bit2  
bit3  
bit4  
bit5  
bit6  
bit7  
bit0  
bit1  
bit2  
bit3  
bit4  
bit5  
bit6  
bit7  
Sunday 1: Enable, 0: Disable  
Monday 1: Enable, 0: Disable  
Tuesday 1: Enable, 0: Disable  
Wednesday 1: Enable, 0: Disable  
Thursday 1: Enable, 0: Disable  
Friday 1: Enable, 0: Disable  
Saturday 1: Enable, 0: Disable  
Every day 1: Enable, 0: Disable  
0x48  
Off Timer Enable  
Sunday 1: Enable, 0: Disable  
Monday 1: Enable, 0: Disable  
Tuesday 1: Enable, 0: Disable  
Wednesday 1: Enable, 0: Disable  
Thursday 1: Enable, 0: Disable  
Friday 1: Enable, 0: Disable  
Saturday 1: Enable, 0: Disable  
Every day 1: Enable, 0: Disable  
Yes  
Yes  
Enable  
Enable  
0x65  
0x66  
IP Setting Mode  
0x00 DHCP  
Yes  
Yes  
Yes  
Enable  
Enable  
Enable  
Enable  
0x01 Manual  
0x02 Speed  
IP Setting Execute  
0x00 Shut Down  
0x01 IP Setting  
0x02 NVR Reset  
0x03 Alarm  
No  
(Continued)  
GXD-L52H1  
6
 
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x67  
IP Setting Result  
0x00 Done  
Yes  
No  
Enable  
Enable  
0x01 Error 1 (UART Commu.)  
0x02 Error 2 (Duplication)  
0x03 Error 3 (IP Add Setting)  
0x04 Error 4 (GW Add setting)  
0x05 Error 5 (DNS1 Setting)  
0x06 Error 6 (DNS2 Setting)  
0x07 Error 7 (Sbnt Msk Setting)  
0x00 100Mbps/Full Duplex  
0x01 100Mbps/Half Duplex  
0x02 10Mbps/Full Duplex  
0x03 10Mbps/Half Duplex  
0x04 Auto  
0x68  
0x70  
Speed Setting  
Yes  
Yes  
Yes  
Yes  
Enable  
Disable  
Enable  
Enable  
Input Skip  
bit0  
bit1  
bit2  
bit3  
bit4  
bit5  
bit6  
bit7  
HD15  
DVI  
HDMI  
VIDEO  
S-VIDEO  
Reserved  
Reserved  
Reserved  
0x71  
0x74  
0x75  
0x76  
0x7A  
Default Input  
0x00 Last Memory  
0x01 Option  
Yes  
No  
Yes  
Yes  
Yes  
Yes  
Yes  
Enable  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
Enable  
Enable  
Digital Signal Detect 0x00 VIDEO  
(DVI/HDMI/etc.)  
*6  
0x01 PC  
*7  
Signal Status  
0x00 Stable  
No  
0x01 Unstable/No Signal  
VIDEO Signal Detect 0x00 NTSC  
0x01 PAL  
No  
Logo Position  
0x00 Auto  
Yes  
0x01 Landscape  
0x02 Portrait  
0x7D  
Power Management 0x00 OFF  
Yes  
Yes  
Disable  
Enable  
*8  
Mode  
0x01 ON  
GXD-L52H1  
7
 
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x7E  
0x7F  
On Screen Logo  
0x00 OFF  
Yes  
Yes  
Enable  
Enable  
0x01 ON (Default)  
0x02 Reserved  
0x00 OFF  
LED  
Yes  
Yes  
Disable  
Enable  
0x01 ON  
*4:  
*5:  
Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable.  
Restricts a part of keys operation following below.  
[Remote Commander]  
Menu, Picture, Sound, ECO (Power Saving), Contrast+/_,Brightness, Chroma, H Shift, V Shift, V size, PAP  
[Main]  
Menu  
*6:  
*7:  
*8:  
Digital Signal Status is Enable for Digital Input Signal Detect Function only in Stable.  
Digital Signal or VIDEO Signal is Enable. Return Signal Status of Active Window.  
Only the panel power supply is turned off at the standby when setting it ON.  
5. Analog Signal Detect Function  
(a) Mode Control  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
Code Table (1-a) [a]  
Code Table (1-d)  
0xFF  
0xXX  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Data2  
Check Sum  
Enquiry  
0x70  
0x00  
0x02  
Code Table (1-a) [b]  
0xFF  
0xXX  
Completed  
Code Table (1-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Yes  
Standby  
Disable  
Power On  
Enable  
0x78  
Analog Signal Detect 0x00 VIDEO  
0x01 PC  
No  
Code Table (1-d)  
Input Select  
1-a[b]  
0x00  
0x01  
0xFF  
Main  
When input is no signal or not supported signal, return value is Video(0x00).  
Sub  
Present input  
GXD-L52H1  
8
 
6. Priority Signal Select Function  
(a) Mode Control  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
Code Table (2-a) [a]  
Code Table (2-d)  
0xFF  
0xXX  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Data2  
Check Sum  
Enquiry  
0x70  
0x00  
0x02  
Code Table (2-a) [b]  
0xFF  
0xXX  
Completed  
Code Table (2-a)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x77  
Priority Signal Select 0x00 Input1 Auto  
0x01 Input1 RGB  
No  
Yes  
Disable  
Enable  
0x02 Input1 YPbPr  
Code Table (2-d)  
Input Select  
0x00  
0x01  
HD15  
Option  
(b) Color Matrix  
Syntax  
Header  
Category  
0x00  
Function  
Data1  
Data2  
Data3  
Data4  
Check Sum  
Control  
0x8C  
Code Table  
(1-b) [a]  
0x04  
Code Table  
(1-c)  
Code Table  
(1-b) [b]  
Code Table  
(1-d)  
0xXX  
Syntax  
Header  
Category  
Function  
Code Table (1-b) [a]  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
Code Table (1-c)  
Code Table (1-d) 0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x00  
0x03  
0x70  
0x73  
Completed  
Command Canceled  
Answer  
Header  
Answer  
Return to  
Data Size  
Return Data1  
Return Data2  
Return Data3  
Check  
Sum  
Enquiry  
0x70  
0x00  
0x04  
Code Table (1-c)  
Code Table (1-b) [b]  
Code Table (1-d) 0xXX Completed  
Code Table (1-b)  
[a]Function  
[b]Range/Switch Code  
Command  
Control  
Enquiry  
Yes  
Standby  
Power On  
0x1D  
Color Matrix  
0x00 YCbCr  
0x01 YPbPr  
Yes  
Disable  
Enable  
GXD-L52H1  
9
 
Code Table (1-c)  
Format Select  
0x00  
0x01  
0x02  
0x03  
480P  
1080i  
720P  
480i  
Code Table (1-d)  
Input Select  
0x00  
0x01  
HD15 (Component)  
Option  
(c) Time Control  
Data Set (Month, Date)  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Check Sum  
Control  
0x8C  
0x00  
0x7C  
0x03  
Month: 0x01-0x0C  
Date: 0x01-0x1F  
0xXX  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
0xFD  
Enquiry  
0x83  
0x00  
0x7C  
0xFF  
0xFF  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Return Data2  
Check Sum  
0xXX  
Enquiry  
0x70  
0x00  
0x03  
Month: 0x00-0x0C Date: 0x01-0x1F  
Completed  
Year Set  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
0xXX  
Control  
0x8C  
0x00  
0x7B  
0x02  
Year: 0x00-0x63  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
0x7B  
0xFF  
0xFF  
0xFC  
GXD-L52H1  
10  
 
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
Enquiry  
0x70  
0x00  
0x02  
Year: 0x00-0x63  
0xXX  
Completed  
Clock Set (Hour, Minute)  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Check Sum  
Control  
0x8C  
0x00  
0x22  
0x03  
Hour: 0x00-0x17  
Minute: 0x00-0x3B  
0xXX  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
0xA3  
Enquiry  
0x83  
0x00  
0x22  
0xFF  
0xFF  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Return Data2  
Check Sum  
*
Enquiry  
0x70  
0x00  
0x03  
Hour: 0x00-0x17  
Minute: 0x00-0x3B  
0xXX  
Completed  
Clock Set (Week)  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
0xXX  
Control  
0x8C  
0x00  
0x23  
0x02  
Week: Code Table (1-e)  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
0x23  
0xFF  
0xFF  
0xA4  
GXD-L52H1  
11  
 
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
Enquiry  
0x70  
0x00  
0x02  
Week: Code Table (1-e)  
0xXX  
Completed  
Code Table (1-e)  
Week Select  
0x00  
0x01  
0x02  
0x03  
0x04  
0x05  
0x06  
Sunday  
Monday  
Tuesday  
Wednesday  
Thursday  
Friday  
Saturday  
On Timer, Off Timer  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Check Sum  
Control  
0x8C  
0x00  
Code Table (1-f) [a]  
0x03  
Hour: 0x00-0x17  
Minute: 0x00-0x3B  
0xXX  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x00  
Code Table (1-f) [a]  
0xFF  
0xFF  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Return Data2  
Check Sum  
Enquiry  
0x70  
0x00  
0x03  
Hour: 0x00-0x17  
Minute: 0x00-0x3B  
0xXX  
Completed  
GXD-L52H1  
12  
 
Code Table (1-f)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
On Timer  
0x50 Sunday  
_
_
_
_
_
_
_
_
Yes  
Yes  
Disable  
Enable  
0x51 Monday  
0x52 Tuesday  
0x53 Wednesday  
0x54 Thursday  
0x55 Friday  
0x56 Saturday  
0x57 Every day  
Off Timer  
0x58 Sunday  
_
_
_
_
_
_
_
_
Yes  
Yes  
Disable  
Enable  
0x59 Monday  
0x5A Tuesday  
0x5B Wednesday  
0x5C Thursday  
0x5D Friday  
0x5E Saturday  
0x5F Every day  
(d) IP Address Setting  
IP Address  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Data4  
Data5  
Check Sum  
Control  
0x8C  
0x00  
0x42  
0x05  
Address 0  
0x00-0xFF  
Address 1  
0x00-0xFF  
Address 2  
0x00-0xFF  
Address 3  
0x00-0xFF  
0xXX  
Subnet Mask  
Syntax  
Header  
0x8C  
Category  
Function  
Data1  
Data2  
Data3  
Data4  
Data5  
Check Sum  
Control  
0x00  
0x61  
0x05  
Address 0  
0x00-0xFF  
Address 1  
0x00-0xFF  
Address 2  
0x00-0xFF  
Address 3  
0x00-0xFF  
0xXX  
Gateway Address  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Data4  
Data5  
Check Sum  
Control  
0x8C  
0x00  
0x62  
0x05  
Address 0  
0x00-0xFF  
Address 1  
0x00-0xFF  
Address 2  
0x00-0xFF  
Address 3  
0x00-0xFF  
0xXX  
DNS Primary  
Syntax  
Header  
0x8C  
Category  
Function  
Data1  
Data2  
Data3  
Data4  
Data5  
Check Sum  
Control  
0x00  
0x63  
0x05  
Address 0  
0x00-0xFF  
Address 1  
0x00-0xFF  
Address 2  
0x00-0xFF  
Address 3  
0x00-0xFF  
0xXX  
GXD-L52H1  
13  
 
DNS Secondary  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Data4  
Data5  
Check Sum  
Control  
0x8C  
0x00  
0x64  
0x05  
Address 0  
0x00-0xFF  
Address 1  
0x00-0xFF  
Address 2  
0x00-0xFF  
Address 3  
0x00-0xFF  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x00  
0x03  
0x70  
0x73  
Completed  
Command Canceled  
IP Address ex)  
192.128.14.1 192 (0xC0) Address 0  
128 (0x80) Address 1  
14 (0x0E) Address 2  
1
(0x01) Address 3  
* IP address command can be carried out even in the standby state.  
Code Table (1-a)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Enable  
Power On  
0x42  
0x61  
0x62  
0x63  
0x64  
IP Address  
_
_
_
_
_
Yes  
Yes  
Enable  
Subnet Mask  
Gateway Address  
DNS Primary  
DNS Secondary  
7. Picture/Sound  
(a) Picture/Sound  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
Enquiry  
0x8C  
0x83  
0x10  
Code Table (2-a) [a] 0x02  
0xFF  
Code Table (2-a) [b]  
0xFF  
0xXX  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
0xXX  
Enquiry  
0x70  
0x00  
0x02  
Code Table (2-a) [b]  
Completed  
GXD-L52H1  
14  
 
Code Table (2-a)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x00  
0x01  
0x02  
0x03  
0x04  
Contrast  
Brightness  
Chroma  
0x00-0x64  
0x00-0x64  
0x00-0x32  
0x00-0x64  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
Enable  
Phase  
Color Temp  
0x00  
Cool  
0x01  
Neutral  
Warm  
Custom  
0x02  
0x03  
0x09  
0x0A  
Sharpness  
NR  
0x00-0x14  
0x00  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
OFF  
0x01  
Low  
0x02  
Mid  
0x03  
High  
0x0B  
0x0C  
Cinema Drive  
0x00  
Auto  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
0x01  
OFF  
Dynamic Picture  
0x00  
OFF  
0x01  
ON  
0x02  
Reserve  
ON  
0x0D  
0x0E  
Color Correct  
0x00  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
0x01  
OFF  
Gamma Correct  
0x00  
High  
0x01  
Mid  
0x02  
Low  
0x10  
Picture Mode  
0x00  
Standard  
Vivid  
Yes  
Yes  
Disable  
Enable  
0x01  
0x02  
Custom  
TC Control  
Conference  
0x05  
0x06  
0x30  
0x31  
0x32  
0x33  
0x34  
Volume  
0x00-0x64  
0x00-0x64  
0x00-0x64  
0x00-0x64  
0x00  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Enable  
Disable  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
Enable  
*1  
Treble  
*1  
Bass  
Balance  
Surround  
OFF  
0x01  
Hall  
0x02  
Simulate  
Dynamic  
Standard  
Reserve  
Custom  
0x35  
Sound Mode  
0x00  
Yes  
Yes  
Disable  
Enable  
0x01  
0x02  
0x03  
(Continued)  
GXD-L52H1  
15  
 
Code Table (2-a)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x36  
0x37  
Default Volume Set 0x00-0x64  
Yes  
Yes  
Yes  
Enable  
Enable  
Enable  
Enable  
Volume Select  
0x00  
0x01  
0x32  
0x46  
0x64  
Last Memory Yes  
Default Setting  
0x38  
Max Volume Set  
50  
Yes  
Yes  
Enable  
Enable  
70  
100  
*1 Sound Mode = Custom Only is Enabled.  
(b) Color Temp  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Data3  
Check Sum  
Control  
0x8C  
0x10  
Code Table (2-b) [a] 0x03  
Code Table (2-c)  
Code Table (2-b) [b]  
0xXX  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x10  
Code Table (2-b) [a] Code Table (2-c)  
0xFF  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x00  
0x03  
0x70  
0x73  
Completed  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Return Data2  
Check Sum  
Enquiry  
0x70  
0x00  
0x03  
Code Table (2-c)  
Code Table (2-b) [b] 0xXX  
Completed  
Code Table (2-b)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x05  
0x06  
0x07  
Red Gain  
Green Gain  
Blue Gain  
0x00-0x1E  
Yes  
Yes  
Disable  
Enable  
Code Table (2-c)  
Format Select  
0x00  
0x01  
0x02  
0x03  
Cool  
Neutral  
Warm  
Custom  
GXD-L52H1  
16  
 
8. Size/Shift  
(a) 8Bits Register  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
Enquiry  
0x8C  
0x83  
0x20  
Code Table (3-b) [a] 0x02  
0xFF  
Code Table (3-b) [b]  
0xFF  
0xXX  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x70  
0x70  
0x00  
0x01  
0x02  
0x03  
0x70  
0x71  
0x72  
0x73  
Completed  
Limit Over  
Limit Under  
Command Canceled  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
0xXX  
Enquiry  
0x70  
0x00  
0x02  
Code Table (3-b) [b]  
Completed  
Code Table (3-b)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x00  
0x01  
0x02  
0x03  
0x04  
H Size  
H Shift  
V Size  
V Shift  
Aspect  
0x00-0x3C  
0x00-0x3C  
0x00-0x0A  
0x00-0x3C  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Enable  
Enable  
0x00 Wide Zoom  
(VIDEO Only)  
0x01 Zoom  
(VIDEO Only)  
0x02 Full  
(VIDEO Only)  
0x04 Normal  
(PC:Real, VIDEO: 4:3)  
0x05 Full 1 (PC Only)  
0x06 Full 2 (PC Only)  
0x00 OFF  
0x05  
Multi Display  
Yes  
Yes  
Disable  
Enable  
0x01 2 x 2  
0x02 3 x 3  
0x03 4 x 4  
0x04 1 x 2  
0x05 1 x 3  
0x06 1 x 4  
0x07 2 x 1  
0x08 3 x 1  
0x09 4 x 1  
(Continued)  
GXD-L52H1  
17  
 
Code Table (3-b)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x06  
0x07  
Auto Pixel Adjust  
Dot Phase  
0xFF Execute  
0x00-0x1F  
Yes  
Yes  
Yes  
No  
Disable  
Disable  
Disable  
Enable  
Enable  
Enable  
Yes  
Yes  
0x0B Multi Position  
(2 x 2 ,1 x 2, 2 x 1)  
0x00 Position1  
0x01 Position2  
0x02 Position3  
0x03 Position4  
0x00 Position1  
0x01 Position2  
0x02 Position3  
0x03 Position4  
0x04 Position5  
0x05 Position6  
0x06 Position7  
0x07 Position8  
0x08 Position9  
0x00 Position1  
0x01 Position2  
0x02 Position3  
0x03 Position4  
0x04 Position5  
0x05 Position6  
0x06 Position7  
0x07 Position8  
0x08 Position9  
0x09 Position10  
0x0A Position11  
0x0B Position12  
0x0C Position13  
0x0D Position14  
0x0E Position15  
0x0F Position16  
0x00 OFF  
*1  
0x0C Multi Position  
Yes  
Yes  
Disable  
Enable  
(3 x 3, 1 x 3, 3 x 1)  
*1  
0x0D Multi Position  
Yes  
Yes  
Disable  
Enable  
(4 x 4, 1 x 4, 4 x 1)  
*1  
0x0E Over Scan  
Yes  
Yes  
Yes  
Yes  
Disable  
Disable  
Enable  
Enable  
0x01 ON  
0x02 AUTO  
0x0F  
Multi Display  
0x00 Tiles  
Output Format  
0x01 Window  
GXD-L52H1  
18  
 
*1 Arrangement of Multi Position.  
Multi Position (2 x 2)  
Multi Position (1 x 2)  
Multi Position (2 x 1)  
1
3
2
4
1
2
1
2
Multi Position (3 x 3)  
Multi Position (1 x 3)  
Multi Position (3 x 1)  
1
4
7
2
5
8
3
6
9
1
2
3
1
2
3
Multi Position (4 x 4)  
Multi Position (1 x 4)  
Multi Position (4 x 1)  
1
5
9
2
6
3
7
4
8
1
2
3
4
1
2
3
4
10 11 12  
13 14 15 16  
GXD-L52H1  
19  
 
9. Status Enquiry  
(a) Model Name  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x00  
0xFF  
0xFF  
0xB1  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
0xXX  
Enquiry  
0x70  
0x00  
0x02  
Code Table (4-a)  
Completed  
Code Table (4-a)  
Format Select  
0x26  
GXD-L52H1  
(b) Serial Number  
Syntax  
Header  
Category  
Function  
Data1  
0xFF  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x01  
0xFF  
0xB2  
Answer Header Answer Return to  
Data Size  
Return Data1 Return Data2 Return Data3 Return Data4 Check Sum  
Enquiry 0x70  
0x00  
0x05  
Upper 8bit  
Data  
Middle Upper  
Data  
Middle Lower Lower 8bit  
Data Data  
0xXX  
Completed  
Return Data1-Data4: 0x00000000-0x0098967F (0,000,000-9,999,999)  
(c) Operation Time  
Syntax  
Header  
Category  
Function  
Data1  
0xFF  
Data2  
Check Sum  
0xB3  
Enquiry  
0x83  
0x30  
0x02  
0xFF  
Answer Header Answer Return to  
Data Size  
Return Data1 Return Data2 Return Data3 Return Data4 Check Sum  
Enquiry 0x70  
0x00  
0x05  
Upper 8bit  
Data  
Middle Upper  
Data  
Middle Lower Lower 8bit  
Data Data  
0xXX  
Completed  
Return Data1-Data4: 0x00000000-0xD693A3FF (0sec.-3,599,999,99sec.)  
(d) Soft Version (Main CPU)  
Syntax  
Header  
Category  
Function  
Data1  
0xFF  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x03  
0xFF  
0xB4  
Answer Header  
Enquiry 0x70  
Answer  
Return to Data Size  
Return Data1  
Upper 8bit Data  
Return Data2  
Check Sum  
0x00  
0x03  
Lower 8bit Data 0xXX  
Completed  
Return Data1-Data2: 0x0000-0xFFFF (BCD Format)  
ex) In Version0.100, it is set to 01 and 00.  
GXD-L52H1  
20  
 
                                                          
.
.
                                                           
For function 0x07, 0x08, 0x09, 0x10, 0x12, 0x13,  
0x14 and 0x16 in the left table  
When the display value is 3.0 V, “0x1E” (30) is  
returned.  
                                                          
                                                           
For function 0x0A, 0x0B and 0x0C, 0x0D in the  
left table  
When the display value is 50 dC, “0x32” (50) is  
returned.  
When the display value is _20 dC, “0xEC” is  
returned.  
(e) 8bits Register  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
Code Table (4-b)  
0xFF  
0xFF  
0xXX  
Answer Header  
Enquiry 0x70  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
0x00  
0x02  
Code Table (4-b) 0xXX  
Completed  
Code Table (4-b)*  
Function  
Return Data  
Unit  
*
0x07  
0x08  
0x09  
0x0A  
0x0B  
0x0C  
0x0D  
0x0E  
0x11  
0x12  
0x13  
0x14  
0x16  
Digital 3.3 V  
Analog 24 V  
Digital 5 V  
Temp1  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0: Normal, 1: Abnormal  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
Temp2  
Temp3  
Temp P/S  
Inverter Alarm  
Shutdown Log  
Digital 3.3 V (Failure)  
Digital 5 V (Failure)  
Analog 12 V (Failure)  
Analog 12 V  
(f) Shutdown Log  
Syntax  
Header  
Category  
Function  
Data1  
0xFF  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x11  
0xFF  
0xC2  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Check Sum  
Enquiry  
0x70  
0x00  
0x02  
Shutdown Log  
0xXX  
Completed  
Code Table (4-c)  
Return Data1: 0x00-0xFF  
Code Table (4-c)  
Shutdown Information  
bit0 Reserved  
bit1 1: FAN Sensor Abnormal  
bit2 1: Panel Abnormal  
0: Normal  
0: Normal  
0: Normal  
bit3 1: Temperature Sensor Abnormal  
bit4 Reserved  
bit5 1: Power Abnormal (3.3 V, 5 V)  
0: Normal  
bit6 1: Analog Power Abnormal (12 V, 9 V, 5 V) 0: Normal  
bit7 Reserved  
GXD-L52H1  
21  
 
(g) Auto Input Detect  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x30  
0xFF  
0xFF  
0xE1  
Answer Header Answer Return to  
Data Size  
Return Data1 Return Data2 Return Data3 Return Data4 Return Data5  
Enquiry 0x70  
0x00  
0x0C  
Input1  
Input2  
Input3  
Input4  
Input5  
Input Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Return Data6 Return Data7 Return Data8 Return Data9 Return Data10  
Option1  
Option1  
Option2  
Option2  
Option3  
Option Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Option Type  
Code Table  
(4-e)  
Input Type  
Code Table  
(4-e)  
Option Type  
Code Table  
(4-e)  
Return Data11 Check Sum  
Option3  
0xXX  
Completed  
Input Type  
Code Table  
(4-e)  
Code Table (4-e)  
Input  
Input Type (Basic)  
Option Type  
Input Type (Option)  
INPUT1  
INPUT2  
INPUT3  
INPUT4  
INPUT5  
OPTION1  
0x06 RGB/YUV (Analog)  
0x07 DVI  
0x00 No Input  
0x00 No Input  
0x00 No Input  
0x00 Analog Only  
0x00 Analog Only  
0x00 Analog Only  
0x00 Analog Only  
0x01 Analog/Com  
0x03 Com Only  
0x00 No Input  
0x03 Video/S-Video  
0x06 RGB/YUV (Analog)  
0x07 Video/S-Video/RGB/YUV (Analog)  
0x04 RGB  
0x00 No Input  
0x04 Digital Only  
0x04 Digital Only  
0x00 Analog Only  
0x00 Analog Only  
0x0E Digital/Digital  
0x0D Digital  
OPTION2  
OPTION3  
0x00 No Input  
0x00 No Input  
GXD-L52H1  
22  
 
(h) Auto Plug Detect  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x32  
0xFF  
0xFF  
0xE3  
Answer  
Header  
Answer  
Return to Data Size  
Return Data1  
Return Data2  
Return Data3  
Enquiry  
0x70  
0x00  
0x21  
Panel Type  
Code Table (4-h)  
H_Resolution (H)  
Code Table (4-i)  
H_Resolution (L)  
Code Table (4-i)  
Return Data4  
Return Data5  
Return Data6  
Return Data7  
V_Resolution (H)  
Code Table (4-i)  
V_Resolution (L)  
Code Table (4-i)  
Input Quantity  
Code Table (4-j)  
Input1  
Input Type  
Code Table (4-e)  
Return Data8  
Return Data9  
Return Data10  
Return Data11  
Input2  
Input3  
Input4  
Input5  
Input Type  
Code Table (4-e)  
Input Type  
Code Table (4-e)  
Input Type  
Code Table (4-e)  
Input Type  
Code Table (4-e)  
Return Data12  
Return Data13  
Return Data14  
Return Data15  
Option Slot Quantity  
Code Table (4-j)  
Option1  
Option Type  
Code Table (4-e)  
Option1  
Input Type  
Code Table (4-e)  
Option2  
Option Type  
Code Table (4-e)  
Return Data16  
Return Data17  
Return Data18  
Return Data19  
Option2  
Input Type  
Code Table (4-e)  
Option3  
Option Type  
Code Table (4-e)  
Option3  
Input Type  
Code Table (4-e)  
(Reserve)  
0xFF  
Return Data20  
Return Data21  
Return Data22  
Return Data23  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
Return Data24  
Return Data25  
Return Data26  
Return Data27  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
Return Data28  
Return Data29  
Return Data30  
Return Data31  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
(Reserve)  
0xFF  
Return Data32  
Check Sum  
(Reserve)  
0xFF  
0xXX  
GXD-L52H1  
23  
 
(i) Auto Panel Type Detect  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0x30  
0x31  
0xFF  
0xFF  
0xE2  
Answer  
Header  
Answer  
0x00  
Return to Data Size  
Return Data1  
Code Table (4-h)  
Check Sum  
Enquiry  
0x70  
0x02  
0x72  
Completed  
Code Table (4-h)  
Code Table (4-i)  
Code Table (4-j)  
H_Resolution  
V_Resolution  
0x0780 (1920)  
0x0438 (1080)  
Input Quantity  
0x05  
0x01  
Panel Type  
Option Slot Quantity  
0x00  
LCD  
Code Table (4-d)  
[a]Function  
[b]Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
Enable  
0x00  
0x01  
0x02  
Model Name  
0x26  
No  
Yes  
Enable  
Serial Number  
Operation Time  
0x000  
0x00000000-0x15751BF0  
(0sec.-359,996,400sec.)  
0x03  
0x07  
0x08  
0x09  
0x0A  
0x0B  
0x0C  
0x0D  
0x0E  
0x11  
0x12  
0x13  
0x14  
0x16  
0x30  
0x31  
Soft Version (Main)  
Digital 3.3 V  
Analog 24 V  
Digital 5 V  
0x0000-0x9999  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
Temp1  
0x00-0xFF  
Temp2  
0x00-0xFF  
Temp3  
0x00-0xFF  
Temp P/S  
0x00-0xFF  
Inverter Alarm  
Shutdown Log  
0: Normal, 1: Abnormal  
0x00-0xFF  
Digital 3.3 V (Failure)  
Digital 5 V (Failure)  
Analog 12 V (Failure)  
Analog 12 V  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
0x00-0xFF  
Auto Input Detect  
Auto Panel Type Detect  
GXD-L52H1  
24  
 
10. User Reset  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
0x8C  
0x50  
Code Table (5) 0x02  
0xFF  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x00  
0x03  
0x70  
0x73  
Completed  
Command Canceled  
Code Table (5)  
Function  
Range/Switch code  
Command  
Control  
Enquiry  
Standby  
Power On  
0x00  
0x01  
0x02  
0x03  
Picture Reset  
Yes  
No  
Disable  
Enable  
Audio Reset  
Size Reset  
Size, Shift  
Picture Reset2  
(FW50)  
Contrast, Brightness,  
Chroma, Phase  
0x04  
All Reset  
11. Service  
(a) Mode  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
0x8C  
0xF0  
Code Table (6) 0x02  
0xFF  
0xXX  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Enquiry  
0x83  
0xF0  
0x00  
0xFF  
0xFF  
0x71  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x70  
0x00  
0x03  
0x70  
0x73  
Completed  
Command Canceled  
Answer  
Header  
Answer  
0x00  
Return to Data Size  
0x02  
Return Data1  
Code Table (7)  
Check Sum  
Enquiry  
0x70  
0xXX  
Completed  
Code Table (6)  
Function  
Range/Switch code  
Command  
Control  
Standby  
Power On  
Normal Mode Service Mode  
0x00  
0x01  
Service Mode IN  
Service Mode Exit  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Enable  
Disable  
Enable  
Enable  
GXD-L52H1  
25  
 
Code Table (7)  
Function  
Range/Switch code  
Command  
Enquiry  
Standby  
Power On  
Normal Mode Service Mode  
Disable Enable  
0x00  
0x01  
User Mode  
Service Mode  
Yes  
Yes  
Yes  
(b) Factory Reset  
Syntax  
Header  
Category  
Function  
Data1  
Data2  
Check Sum  
Control  
0x8C  
0x40  
Code Table (8) 0x02  
0xFF  
0xXX  
Answer  
Header  
Answer  
Check Sum  
Control  
0x70  
0x00  
0x70  
Completed  
0x70  
0x03  
0x73  
Command Canceled  
Code Table (8)  
Function  
Range/Switch  
code  
Command  
Control  
Enquiry  
Standby  
No  
Power On  
Normal Mode Service Mode  
Disable Enable  
0x88 Factory Reset  
Yes  
No  
Yes  
GXD-L52H1  
26  
 
The material contained in this manual consists of  
information that is the property of Sony Corporation.  
Sony Corporation expressly prohibits the duplication of  
any portion of this manual or the use thereof for any  
purpose other than the operation or maintenance of the  
equipment described in this manual without the express  
written permission of Sony Corporation.  
Le matériel contenu dans ce manuel consiste en  
informations qui sont la propriété de Sony Corporation.  
Sony Corporation interdit formellement la copie de  
quelque partie que ce soit de ce manuel ou son emploi  
pour tout autre but que des opérations ou entretiens de  
l’équipement à moins d’une permission écrite de Sony  
Corporation.  
Das in dieser Anleitung enthaltene Material besteht aus  
Informationen, die Eigentum der Sony Corporation sind.  
Die Sony Corporation untersagt ausdrücklich die  
Vervielfältigung jeglicher Teile dieser Anleitung oder den  
Gebrauch derselben für irgendeinen anderen Zweck als  
die Bedienung oder Wartung der in dieser Anleitung  
beschriebenen  
Ausrüstung  
ohne  
ausdrückliche  
schriftliche Erlaubnis der Sony Corporation.  
GXD-L52H1  
 
Printed in Japan  
2008. 1 22  
©2008  
GXD-L52H1 (WW) E  
9-968-408-01  
Sony Corporation  
 

Sennheiser Microphone SLT24520FC User Manual
Sharp Calculator CS 2870 User Manual
Silva Boating Equipment 70p User Manual
SMSC Switch LAN9311 User Manual
Sony Clock Radio ICF C490L User Manual
Sony CRT Television KV VF21M40 User Manual
Sony Home Theater Server HT XT1 User Manual
Sony Stereo System 3 097 194 151 User Manual
Southbend Lathe sb1016 User Manual
Sunbeam Iron 3050 User Manual