Shure TV Antenna UAPF X1 User Manual

Wireless Systems  
UAPF-X1  
UHF IN-LINE  
PASSIVE  
RF FILTER  
©2008 Shure Incorporated  
27A12024 (Rev. 2)  
Printed in U.S.A.  
*27A12024*  
 
General Description  
The Shure UAPF-X1 is an in-line passive RF filter to attenuate frequencies outside the  
X1 band and intended to be used with any Shure X1 band wireless product that has  
removable antennas, including SLX, ULX, and UHFR.  
FeatUres  
Filters out extraneous RF signals.  
Mountable on supplied desk-/wall-mount or on a microphone stand  
Extremely durable under the heaviest use  
Shure quality, ruggedness, and reliability  
application  
Optimally, the unit should be located prior to any amplification of an RF signal.  
Positioning should be tested and adjusted for each individual setup.  
Antennas should be spaced far enough to obtain the widest possible RF field and to  
minimize RF signal drop out. In a diversity system, Shure recommends that antennas  
be positioned at 45°.  
networking  
antenna  
B
in  
antenna  
A
in  
receiver outputs  
200  
network  
activity  
line  
mic  
lift  
GND  
12.7V  
out  
12.7V  
out  
ethernet  
RJ-45  
150mA  
150mA  
45  
45  
Figure 1. Diversity System  
The following table shows three typical connectivity arrangements for the UAPF-X1:  
Antenna  
Passive  
Filter  
In line  
Amplifier  
Antenna  
Distribution  
Unit  
Receiver  
UA820X (or  
PA805SWB,  
UA860SWB,  
PA805X)  
UAPF-X1  
UAPF-X1  
UAPF-X1  
UR4D-X1 (or  
UA4S-X1)  
UA820X (or  
PA805SWB,  
UA860SWB,  
PA805X)  
UA845-SWB  
UA845-SWB  
UR4D-X1 (or  
UA4S-X1)  
UA820X (or  
PA805SWB,  
UA860SWB,  
PA805X)  
UA830X  
UR4D-X1 (or  
UA4S-X1)  
3
 
installation  
IMPORTANT: DO NOT USE INFORMATION:  
This device must not be used with antennas or other devices that have a DC short  
circuit at their feed point without using an external (BNC) DC Block. A suitable BNC  
DC Block is the JFW Industries Model 50DB-002.  
installation instrUctions  
1. Thread the Shure Model UAPF-X1 unit on the supplied stand or on a 5/8 in.-27  
thread microphone stand (Figure 2) and connect the antenna wand to either antenna  
port (filter functions in both directions).  
To Antenna  
Figure 2. Attaching Base and Antenna  
2. Using 50 W low-loss coaxial cable (purchased separately, Shure UA825 or UA850  
or UA8100 recommended), connect to the opposite port to the Shure Model UR4  
or ULX, SLX wireless receiver or UA845SWB, or UA844SWB Antenna Distribution  
System (Figure 3).  
To Receiver  
Antenna In  
UR4 WiReleSS ReCeiveR  
Figure 3: Connecting Receiver  
4
 
MaintaininG cable inteGrity  
To maintain Shure cables in top condition in permanent installations:  
1. Avoid sharp bends or kinks in the cables.  
2. Do not deform cables with makeshift clamps, such as bending a nail over the cable.  
3. Do not use cables in permanent outdoor installations.  
4. Do not expose cables to extreme moisture  
Figure 4: Cable Chaining  
speciFications  
RF frequency range..............................................................3dB bandwidth = 36Mhz  
.............................20dB bandwidth = 49Mhz  
Stop-Band Attenuation: ..........................................Minimum 30dB, Typical 32-36dB  
Insertion Loss....................................................................................Typical 3.25dB  
Case..................................................................Aluminum die-casting, black painted  
vSWR in pass-band (input, output):.......................................................Typical 2.0dB  
Swivel Adapter ............................................................Positive action, break-resistant  
adjustable from 0 degrees to 90 degrees,  
with standard 5/8 in. –27 thread  
Net Weight.......................................................Without mounting stand.28kg (9.8 oz)  
.......................................................................With mounting stand .42 kg (14.8 oz)  
Power Consumption (12 vdc)................. Passively passes power (12vdc) 0.6 to 0.72 W  
for use with UA870X active antenna.  
Connectors....................................................................................Female, BNC-type  
Dimensions (without accessories)...............66.7 mm high x 31.75 mm wide x 112 mm  
deep (2.625 x 1.250 x4.40 inches), 108 mm  
(4.25 in.) high w/mounting stand  
replaceMent parts  
Mounting Base ..........................................................................................A13HDB  
For additional service or parts information, please contact Shure’s Service department  
at 1-800-516-2525. Outside the United States, please contact your authorized Shure  
Service Center.  
5
 
SHURE Incorporated http://www.shure.com  
United States, Canada, Latin America, Caribbean:  
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.  
Phone: 847-600-2000  
U.S. Fax: 847-600-1212  
Intl Fax: 847-600-6446  
Europe, Middle East, Africa:  
Shure Europe GmbH, Phone: 49-7131-72140  
Fax: 49-7131-721414  
Asia, Pacific:  
Shure Asia Limited, Phone: 852-2893-4290  
Fax: 852-2893-4055  
 

Sharp All in One Printer CINSE4653DS51 User Manual
Sharp Refrigerator SJ560M User Manual
Shiro Cordless Telephone SD8101 User Manual
Sony Car Stereo System CDX 1000RF User Manual
Sony CD Player CDP CE275 User Manual
Sony Stereo Receiver STR DA333ES User Manual
Stamina Products Elliptical Trainer 55 1615 User Manual
Stiga Lawn Mower 8211 0208 08 User Manual
Tanaka Drill T277487 User Manual
Tanaka Trimmer TBC 4000 User Manual