Sharp Car Video System PN ZS1C User Manual

Installation procedure  
Main specifications  
(continued)  
Operation Manual  
Stand cover  
PN-ZS1C  
Model  
Dimensions See the figure below.  
Approx. 77 kg (169.8 lbs.) (Weight includes  
support rods, covers and screws)  
PN-ZS1C  
Attach the left and right back cover with 16 supplied  
5
M6 screws.  
Weight  
Cables can  
be bundled by  
Applicable models (as of July 2008) LCD MONITOR LB-1085  
As a part of our policy of continuous improvement, SHARP reserves  
the right to make design and specification changes for product  
improvement without prior notice. The performance specification  
figures indicated are nominal values of production units. There may  
be some deviations from these values in individual units.  
attaching the cable  
clamp to the back  
cover.  
Back cover  
Thank you for purchasing a SHARP product.  
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the  
section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be  
accessed at any time.  
Unit: mm (inch)  
(The figure shows the approximate values.)  
TIPS  
- Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party,  
nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized  
under law.  
Attach the cover reinforcement angle with the  
6
- This product and its accessories may be upgraded without advance notice.  
supplied M6 screws to secure the front cover. (Use  
10 screws for 1600 mm (63 inch), 7 screws for  
1500 mm (59 1/16 inch).)  
To ensure safe and correct use  
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels  
and incorrectly using the product could have results as classified below.  
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all  
instructions.  
*
*
*
1670 (65 3/4)  
* Height when mounted at 1600 mm (63 inch)  
/ /16 inch)  
715 mm (28 1 8 inch) when mounted at 1500 mm (59 1  
Not following these instructions could result in death or serious injury.  
Warning:  
* Not used when 1500 mm (59 1  
/16 inch)  
The installation must be performed by qualified service personnel.  
Improper installation work may cause the monitor to fall or topple over, resulting in injury.  
• Secure the stand with the anchor bolts before assembling these parts.  
Otherwise, the monitor may topple over, resulting in injury.  
Only use the accessories with specified models. Do not modify the LCD Monitor or the accessories.  
Otherwise, the monitor may fall or topple over, resulting in injury.  
Not following these instructions could result in injury or property damage.  
Caution:  
• Tighten all the screws and bolts fully and securely.  
Insufficient tightening may cause the monitor to fall or topple over, resulting in injury.  
When any deformation or cracks are found please stop using the LCD Monitor.  
Using the monitor without repairing the problem may cause the monitor to fall or topple over, resulting in injury.  
Printed in Japan  
EN(1)  
-
4
-
-
1
-
 

Sharp PDAs Smartphones EL 6985 User Manual
Silex technology Network Card Sewing Machine Wireless Network Adapter User Manual
Singer Sewing Machine 107W50 User Manual
Snapper Snow Blower MCS2000 User Manual
Sony Flat Panel Television XBR65X930C User Manual
Sony Speaker SRS A201 User Manual
Speco Technologies Stereo Amplifier P120FACD P240FACD User Manual
Speco Technologies Switch IP POEH101 User Manual
Spectra Watermakers Water System MPC 5000 User Manual
Sunbeam Coffeemaker MM8400 User Manual