RocketFish TV Mount RF TVMFM02 User Guide

RF-TVMFM02_10-0565_QSG_V1_ENN.eps  
1
6/2/2010  
6:03::12 PM  
QUICK SETUP GUIDE  
1 Install the TV bracket  
2 Install the arm assembly  
RF-TVMFM02  
Option 1: Installing for a flat mounting surface  
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).  
Option 1: Installing to a wood stud wall  
1 Locate the stud. Verify the center of the stud with an awl  
or thin nail or use an edge-to-edge stud finder.  
2 Level the arm assembly (B) and mark the hole locations.  
3 Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.  
4 Align the arm assembly (B) with the pilot holes.  
5 Place the washers (D) over the holes in the  
arm assembly, insert the lag bolts (E)  
1 Align the TV bracket (A) with the screw holes on the back of the TV.  
2 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket,  
then insert the M4 screws (F), M5 screws (J), or M6 screws (L or M) through the washers.  
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
<5/8 in.  
through the washers, then tighten  
the lag bolts only until the washers  
are pulled firmly against the arm  
assembly.  
CAUTION: Avoid potential injuries or  
property damage!  
or  
or  
DO NOT over-tighten the lag bolts (E).  
Wall  
(75 mm)  
3 in.  
9-7/10 in.  
Thank you for choosing the Rocketfish RF-TVMFM02.  
The RF-TVMFM02 TV mount is designed to support a  
flat-panel TV weighing up to 60 lbs. (27.2 kg).  
TV  
7 in.  
TV shifts 7 in. from the home position  
to full extension.  
M6 bag  
Package contents  
L M6 × 12 mm screws (4)  
M M6 × 20 mm screws (4)  
N M6 × 35 mm screws (4)  
O M6/M8 washers (4)  
P M6/M8 spacers (4)  
M8 bag  
Q M8 × 40 mm screws (4)  
Hex key bag  
R 3/16 in. hex key (1)  
S 5/32 in. hex key (1)  
Cap screw  
A TV bracket (1)  
B Arm assembly (1)  
Lag bolt bag  
C Concrete anchor (2)  
D Lag bolt washer (2)  
E 5/16 in. × 2-3/4 in. lag bolt (2)  
M4 bag  
F M4 × 12 mm screws (4)  
G M4 × 30 mm screws (4)  
H M4/M5 washers (8)  
I M4/M5 spacers (4)  
M5 bag  
J M5 × 12 mm screws (4)  
K M5 × 30 mm screws (4)  
Option 2: Installing to a solid concrete or concrete block wall  
1 Level the arm assembly (B) and mark the hole locations.  
2 Drill pilot hole to a depth of 3 in. using a 3/8 in. diameter drill bit.  
3 Insert the concrete wall anchors (C) into the pilot holes  
and make sure that the anchors are seated flush with  
the concrete surface.  
4 Align the arm assembly (B) with the anchors.  
5 Place the washers (D) over the holes in the arm assembly,  
insert the lag bolts (E) through the washers, then tighten  
the lag bolts only until the washers (D) are pulled firmly  
against the arm assembly.  
C
M
Option 2: Installing for an obstructed mounting surface  
Note: Use additional washers (H) with M4/M5 hardware only.  
1 Align the TV bracket (A) with the screw holes on the back of the TV.  
2 Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket,  
then insert the M4 screws (G), M5 screws (K), or M6 screws (N or Q) through the washers.  
3 Tighten the screws until they are snug against the TV bracket. Do not over tighten.  
Y
CM  
MY  
CY  
CMY  
K
CAUTION: To prevent property  
damage or personal injury, never  
drill into mortar between blocks.  
Mount wall plate directly onto the  
concrete surface.  
T Cap screw (1)  
Cable ties  
U 8 in. nylon cable ties (5)  
CAUTION: Avoid potential injuries or property damage!  
Lag bolt bag  
DO NOT over-tighten the lag bolts (E).  
5/16 in. × 2-3/4 in.  
M4 bag  
or  
or  
M4 × 12 mm  
M4 × 30 mm  
M4/M5  
M4/M5  
or  
M5 bag  
M5 × 12 mm  
M5 × 30 mm  
M6 bag  
M6/M8  
M6 × 12 mm  
M6 × 20 mm  
M6 × 35 mm  
M6/M8  
M8 bag  
Hex key bag  
3/16 in.  
M8 × 40 mm  
Cap screw  
(75 mm)  
3 in.  
5/32 in.  
Cable ties  
Tools you will need:  
• Stud finder  
• Awl  
• Socket wrench with  
1/2 in. socket or  
• Pencil  
• Level  
• Tape measure  
• Phillips screwdriver  
• Hammer (concrete only)  
adjustable wrench  
• 7/32 in. wood drill bit  
• 3/8 in. masonry drill bit  
(concrete only)  
• Power drill  
 

Pyramid Car Audio Car Amplifier PB440X User Guide
RCA Car Video System DRC62708 User Guide
Realistic Scanner PRO 50 User Guide
Rolls Stereo Receiver RDB109 User Guide
Royal Sovereign Laminator PL 1310 User Guide
Samsung Camcorder D371Wi User Guide
Samsung Clothes Dryer DV218AEW User Guide
Samsung DVD Recorder DVD R145 User Guide
Sanyo CRT Television CE27LD4 B User Guide
Scientific Atlanta DVR 3250HDTM User Guide