PYLE Audio TV Mount PSW503ST User Guide

Step 4: Hanging display  
Firstly lift the bracket mounted display over the wall mount. And then hook the  
brackets over the top of the wall mount. Rotate the display let the bottom of the  
brackets hook over the bottom of wall mount, as shown in Fig.4a. Then put safe  
bolts into the bottom of the brackets and lock it, as shown in Fig.4b.  
Tilt Flat Panel TV Bracket  
Warning: Some TV require two people to lift, as we are not responsible for any  
personal injury or product damage due to mishandling.  
Multifunctional double deck wall mount  
INSTALLATION GUIDE  
Item No.:PSW503ST  
2,3  
1
5
the facing of a quilt  
Fig 4a  
Fig 4b  
Thank you for choosiing our products  
Easy installing: Just hang up the display  
Safety: locking by spinning bolt on the bottom  
Weight Capacity:10kg/22lbs~50kg/110lbs  
TV size range: 26"~42"  
Pyle Audio  
Adjustable angle: -5 15  
1600 63rd st , Brooklyn, NY, 11204  
(718)236-8000  
Inside has balance adjust system  
www.pyleaudio.com  
Bulit in leveler system  
MADE IN CHINA  
-8-  
IMPORTANT: If don’t understand about right install ways, please  
consult to normal installing specialist.  
 
Step 2: Install the Cable Cover  
WARNING  
Route the cables as required. Snap the cable cover into place onto  
the rods (Fig. 2a), and then slide the cover into position as required.  
(Fig. 2b)  
We are not responsible for any personal injury or product damage due to mishandling,  
incorrect mounting, incorrect assembly or incorrect use of this product.  
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold  
cinder block walls. If you are uncertain about the nature of your wall, please consult a  
qualified contractor. If the hardware you required is not included please contact your  
local hardware store.  
Fig 2a  
Fig 2a  
Caution:  
This Product LCD /Plasma Wall Mount Bracket is intended for use only  
Step 3: Attach mount to wall  
with the maximum weights indicated .See apparatus instructions .Use with products  
heavier than the maximum weights indicated may result in instability causing possible  
injury .  
First, determine the height of stand  
The best height of stand is parallel to eyelevel of a person who sitting on a couch.  
Normally, the horizontal distance of eyelevel is about 4’ from ground level.  
The following two conditions are for determining the perfect height of stand:  
1) the distance between wall and couch(Fig 3a).  
Step 1: Attach bracket to TV  
Check your TV manual to confirm the diameter of bolt to be used or choose an  
appropriate bolt according to size, height and position of the holes on your TV. See  
pages 4-5 of these instructions for examples.  
2) the distance of eyelevel from ground level plus the distance measured from  
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 3a).  
For example:  
For correct installing, make sure that hook of every bracket must facing down. Use  
selected bolts, spacers and washers for installing bracket at the back of display.  
Adjust two brackets to equal heights and level. Once aligned, tightly secure the  
bolts.  
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’  
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’  
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’  
The perfect height of stand centre will be anywhere within b, where you feel  
comfortable for viewing.  
IMPORTANT: Don't force the bolt into the hole, which will cause a damage of  
equipments and injure of person. Don't use electric drill to fasten any bolts.  
15 degree  
viewing angle  
b
eyelevel  
a
Fig 3a  
-3-  
-6-  
 
Following examples shows how to use bolts, spacers and square washers.  
2. Some displays have curved backs with  
recessed mounting lands(Fig.a). It will  
require the use of spacer. For this display,  
install a spacer(K) between display and  
the bracket. As shown in Fig 1b.  
1.Some displays have vertical backs. No spacer is required. Install the bracket directly  
to the back of display by using bolts and square washers provided. As shown in Fig.1a.  
Fig a  
M4 Fig bit  
M5 Fig bit  
M5 Fig bit  
M6 Fig bit  
K
K
A,B  
3
E
F
2
G
C
G
3
3
G
G
M6 Fig bit  
Fig 1b  
3
D
G
Fig 1a  
-5-  
-4-  
 

RCA Portable DVD Player XDVD181 User Guide
RCA Projection Television HD61LPW165 User Guide
Reebok Fitness Treadmill RBTL09500 User Guide
Regency Indoor Fireplace P48 LP2 User Guide
Remington Electric Shaver CORDLESS RECHARGEABLE SHAVER User Guide
Renesas Computer Hardware M16C 29 User Guide
Samsung All in One Printer SCX 6322DN User Guide
Samsung CRT Television WS32A11SP User Guide
Samsung Digital Camera u ca5 User Guide
Sangean Electronics Car Satellite Radio System RCR 5 User Guide