Panasonic Personal Computer CF 51 User Manual

OPERATING INSTRUCTIONS  
Personal Computer  
Model No.  
CF-51  
series  
Contents  
Getting Started  
Read Me First ..............................................3  
Description of Parts .......................................9  
Useful Information  
Troubleshooting  
Appendix  
Contrat de licence d’usage limité......................25  
Specifications ............................................26  
LIMITED WARRANTY ..................................29  
For more information about the com-  
puter, you can refer to the on-screen  
manual.  
To access the on-screen manual.  
Î page 14 “On-screen Manual”  
Please read these instructions carefully before using this product and save this manual for future use.  
 
Read Me First  
Models for U.S.A.  
harmful interference to co-channel Mobile Satellite sys-  
tems.  
Federal Communications Commission Radio Fre-  
quency Interference Statement  
High power radars are allocated as primary users of the  
5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These  
radar stations can cause interference with and/or damage  
this product.  
Note: This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interfer-  
ence in a residential installation. This equipment gener-  
ates, uses and can radiate radio frequency energy and, if  
not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television recep-  
tion, which can be determined by turning the equipment  
off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
z Reorient or relocate the receiving antenna.  
z Increase the separation between the equipment and  
receiver.  
z Connect the equipment into an outlet on a circuit differ-  
ent from that to which the receiver is connected.  
z Consult the Panasonic Service Center or an experi-  
enced radio/TV technician for help.  
FCC Regulation Notice for modem  
This equipment contains a FCC approved modem.  
1. This equipment complies with CFR47 Part 68 rules.  
On the computer is a label that contains, among other  
information, the FCC registration number and ringer  
equivalence number (REN) for this equipment. If  
required, this information must be provided to the tele-  
phone company.  
2. An FCC compliant telephone cord and modular plug is  
provided with this equipment. This equipment is  
designed to be connected to the telephone network or  
premises wiring using a compatible modular jack  
which is Part 68 compliant. See Installation Instruc-  
tions for details.  
Warning  
To assure continued compliance, use only shielded inter-  
face cables when connecting to a computer or peripheral.  
Also, any changes or modifications not expressly  
approved by the party responsible for compliance could  
void the user’s authority to operate this equipment.  
3. The REN is used to determine the quantity of devices  
which may be connected to the telephone line. Exces-  
sive RENs on the telephone line may result in the  
devices not ringing in response to an incoming call. In  
most, but not all area, the sum of RENs should not  
exceed five (5.0). To be certain of the number of  
devices that may be connected to a line, as deter-  
mined by the total RENs, contact the local telephone  
company.  
4. If your telephone equipment cause harm to the tele-  
phone network, the telephone company will notify you  
in advice that temporary discontinuance of service  
may be required. But if advice notice isn’t practical, the  
telephone company will notify the customer as soon as  
possible. Also, you will be advised of your right to file a  
complaint with the FCC if you believe it is necessary.  
5. The telephone company may take changes in its facili-  
ties, equipment, operations or procedures that could  
affect the operation of the equipment. If this happens  
the telephone company will provide advance notice in  
order for you to make necessary modifications to  
maintain uninterrupted service.  
6. If trouble is experienced with this equipment, for repair  
or warranty information, please contact Panasonic  
Corporation of North America at DIAL TOLL FREE 1-  
800-LAPTOP5 (1-800-527-8675). If the equipment is  
causing harm to the telephone network, the telephone  
company may request that you disconnect the equip-  
ment until the problem is resolved.  
7. There are no user serviceable parts contained in this  
equipment.  
8. This equipment may not be used on coin service pro-  
vided by the telephone company. Connection to party  
lines is subject to state tariffs.  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) This device must accept any interference received,  
including interference that may cause undesired oper-  
ation.  
Responsible Party:  
Panasonic Corporation of North America  
One Panasonic Way  
Secaucus, NJ 07094  
Tel No:1-800-LAPTOP5 (1-800-527-8675)  
<Only for model with wireless LAN>  
FCC RF Exposure Warning:  
z This equipment complies with FCC radiation exposure  
limits set forth for an uncontrolled environment.  
z This equipment must be installed and operated in  
accordance with provided instructions and minimum  
1.5 cm spacing must be provided between antenna  
and all person’s body (excluding extremities of hands,  
wrist and feet) during wireless modes of operation.  
z This transmitter must not be co-located or operated in  
conjunction with any other antenna or transmitter.  
z This computer is provided with a PC Card slot that  
could be used with wireless transmitter(s), which will  
be specifically recommended, when they become  
available. Other third-party wireless transmitter(s)  
have not been RF exposure evaluated for use with this  
computer and may not comply with FCC RF exposure  
requirements.  
9. The Telephone Consumer Protection Act of 1991  
makes it unlawful for any person to use a computer or  
other electronic device to send any message via a  
telephone fax machine unless such message clearly  
contains in a margin at the top or bottom of each  
This product is restricted to indoor use due to its operation  
in the 5.15 to 5.25 GHz frequency range.  
FCC requires this product to be used indoors for the fre-  
quency range 5.15 to 5.25 GHz to reduce the potential for  
3
 
Read Me First  
“ATTENTION : Pour réduire le risque d’incendie, utiliser  
uniquement des conducteurs de télécommunications 26  
AWG ou de section supérieure.”  
transmitted page or on the first page of the transmis-  
sion, the date and time it is sent and an identification of  
the business or other entry, or other individual sending  
the message and the telephone number of the sending  
machine or such business, other entity, or individual. In  
order to program this information into your fax soft-  
ware, you should refer to the manual of the Fax soft-  
ware being used.  
Notice for the products using LCD  
This product has a fluorescent lamp that contains mer-  
cury. Disposal may be regulated in your community due to  
environmental considerations.  
For disposal or recycling information, please contact your  
local authorities, or the Electronics Industries Alliance:  
<http://www.eiae.org/>  
10.According to the FCC’s electrical safety advisory, we  
recommend that you may install an AC surge arrestor  
in the AC outlet to which this equipment is connected.  
Telephone companies report that electrical surges,  
typically lightning transients, are very destructive to  
customer terminal equipment connected to AC power  
sources and that this is a major nationwide problem.  
For U.S.A.-California Only  
This product contains a CR Coin Cell Lithium Battery  
which contains Perchlorate Material - special handling  
may apply.  
“Caution : To reduce the risk of fire, use only No.26 AWG or  
larger telecommunication line cord.”  
Models for Canada  
Industry Canada (IC) Notice for modem  
This equipment contains an Industry Canada approved  
modem unit.  
RESTRICTIONS CONCERNANT LE RACCORDEMENT  
DE MATÉRIEL  
“AVIS: L’étiquette d’Industrie Canada identifie le matériel  
homologué. Cette étiquette certifie que le matériel est  
conforme aux normes de protection, d’exploitation et de  
sécurité des réseaux de télécommunications, comme le  
prescrivent les documents concernant les exigences tech-  
niques relatives au matériel terminal. Le Ministère  
n’assure toutefois pas que le matériel fonctionnera à la  
satisfaction de l’utilisateur.  
Avant d’installer ce matériel, l’utilisateur doit s’assurer  
qu’il est permis de le raccorder aux installations de l’entre-  
prise locale de télécommunication. Le matériel doit égale-  
ment être installé en suivant une méthode acceptée de  
raccordement.  
L’abonné ne doit pas oublier qu’il est possible que la con-  
formité aux conditions énoncées ci-dessus n’empêche  
pas la dégradation du service dans certaines situations.  
Les réparations de matériel homologué doivent être coor-  
données par un représentant désigné par le fournisseur.  
L’entreprise de télécommunications peut demander à  
l’utilisateur de débrancher un appareil à la suite de répa-  
rations ou de modifications effectuées par l’utilisateur ou à  
cause de mauvais fonctionnement.  
Pour sa propre protection, l’utilisateur doit s’assurer que  
tous les fils de mise à la terre de la source d’énergie élec-  
trique, des lignes téléphoniques et des canalisations  
d’eau métalliques, s’il y en a, sont raccordés ensemble.  
Cette précaution est particulièrement importante dans les  
régions rurales. Avertissement: L’utilisateur ne doit pas  
tenter de faire ces raccordements lui-même; il doit avoir  
recours à un service d’inspection des installations élec-  
triques, ou à un électricien, selon le cas.”  
The Industry Canada label is affixed on the modem unit.  
EQUIPMENT ATTACHEMENT LIMITATIONS  
“NOTICE: The Industry Canada label identifies certified  
equipment. This certification means that the equipment  
meets telecommunications network protective, opera-  
tional and safety requirements as prescribed in the appro-  
priate Terminal Equipment Technical Requirements  
document(s). The Department does not guarantee the  
equipment will operate to the user’s satisfaction.  
Before installing this equipment, users should ensure that  
it is permissible to be connected to the facilities of the  
local telecommunications company. The equipment must  
also be installed using an acceptable method of connec-  
tion. The customer should be aware that compliance with  
the above conditions may not prevent degradation of ser-  
vice in some situations.  
Repairs to certified equipment should be coordinated by a  
representative designated by the supplier. Any repairs or  
alterations made by the user to this equipment, or equip-  
ment malfunctions, may give the telecommunications  
company cause to request the user to disconnect the  
equipment.  
Users should ensure for their own protection that the elec-  
trical ground connections of the power utility, telephone  
lines and internal metallic water pipe system, if present,  
are connected together. This precaution may be particu-  
larly important in rural areas. Caution: Users should not  
attempt to make such connections themselves, but should  
contact the appropriate electric inspection authority, or  
electrician, as appropriate.”  
“NOTICE: The Ringer Equivalence Number (REN)  
assigned to each terminal device provides an indication of  
the maximum number of terminals allowed to be connected  
to a telephone interface. The termination on an interface  
may consist of any combination of devices subject only to  
the requirement that the sum of the Ringer Equivalence  
Numbers of all the devices does not exceed 5.”  
“AVIS: L’indice d’équivalence de la sonnerie (IES) assigné  
à chaque dispositif terminal indique le nombre maximal de  
terminaux qui peuvent être raccordés à une interface. La  
terminaison d’une interface téléphonique peut consister  
en une combinaison de quelques dispositifs, à la seule  
condition que la somme d’indices d’équivalence de la  
sonnerie de touts les dispositifs n’excède pas 5.”  
IES: Voir sous le fond de l’ordinateur  
REN: See bottom of the computer  
4
 
<Only for model with wireless LAN>  
2. Avoid using a telephone (other than a cordless type)  
during an electrical storm. There may be a remote risk  
of electric shock from lightning.  
3. Do not use the telephone to report a gas leak in the  
vicinity of the leak.  
4. Use only the power cord and batteries indicated in this  
manual. Do not dispose of batteries in a fire. They may  
explode. Check with local codes for possible special  
disposal instructions.  
Industry Canada  
This product complies with RSS210 Industry Canada.  
Operation is subject to the following two conditions;  
(1) this device may not cause interference, and  
(2) this device must accept any interference, including  
interference that may cause undesired operation of  
the device.  
SAVE THESE INSTRUCTIONS  
Certaines mesures de sécurité doivent être prises pen-  
dant l’utilisation de matérial téléphonique afin de réduire  
les risques d’incendie, de choc électrique et de blessures.  
En voici quelquesunes:  
1. Ne pas utiliser l’appareil près de l’eau, p.ex., près  
d’une baignoire, d’un lavabo, d’un évier de cuisine,  
d’un bac à laver, dans un sous-sol humide ou près  
d’une piscine.  
2. Éviter d’utiliser le téléphone (sauf s’il s’agit d’un appar-  
eil sans fil) pendant un orage électrique. Ceci peut  
présenter un risque de choc électrique causé par la  
foudre.  
3. Ne pas utiliser l’appareil téléphonique pour signaler  
une fuite de gaz s’il est situé près de la fuite.  
4. Utiliser seulement le cordon d’alimentation et le type  
de piles indiqués dans ce manual. Ne pas jeter les  
piles dans le feu: elles peuvent exploser. Se conformer  
aux règlements pertinents quant à l’élimination des  
piles.  
Models for Europe  
<Only for model with a “CE” mark on the bottom of  
the computer>  
Declaration of Conformity (DoC)  
“Hereby, we declare that this Personal  
Computer is in compliance with the  
essential requirements and other rele-  
vant provisions of the Directive 1999/5/  
EC.”  
Hint:  
If you want to get a copy of the original DoC of our prod-  
ucts which relates to the R&TTE, please contact our web  
Contact:  
Panasonic Services Europe  
A Division of Panasonic Marketing Europe GmbH  
Panasonic Testing Centre  
CONSERVER CES INSTRUCTIONS  
Network connection.  
The terminal equipment is intended for connection to the  
following public network;  
Lithium Battery / Pile au lithium  
In all the countries of European Economical Area;  
- Public Switched Telephony Networks  
Lithium Battery!  
Technical Features.  
This computer contains a lithium battery to enable the  
date, time, and other data to be stored. The battery should  
only be exchanged by authorized service personnel.  
Warning!  
The terminal equipment includes the following features;  
- DTMF dialing  
- Maximum bitrate receiving mode: 56 kbit/s  
- Maximum bitrate sending mode: 33.6 kbit/s  
This product is designed to interwork with the Public  
Switched Telecommunication Networks in UK, Ireland,  
Netherlands, Sweden, Denmark, Finland, Switzerland,  
Luxembourg, Belgium, France, Germany, Spain, Portugal,  
Iceland, Greece, Italy, Norway and Austria.  
A risk of explosion from incorrect installation or misappli-  
cation may possibly occur.  
Pile au lithium!  
Le micro-ordinateur renferme une pile au lithium qui per-  
met de sauvegarder certaines données, notamment la  
date et l’heure. La pile ne doit être remplacée que par un  
technicien qualifié.  
Compliance Notice - CE Mark  
This equipment is in conformance with the requirements  
of the European Council Directive listed below:  
73/23/EEC Low Voltage Directive with amendment 93/68/  
EEC  
Danger !  
Risque d’explosion en cas de non respect de cette mise  
en garde!  
89/336/EEC EMC Directive with amendments 92/31/EEC  
and 93/68/EEC  
1999/5/EC R&TTE  
Information to the User  
Important Safety Instructions /  
Importantes Mesures De Sécurité  
<Only for model with wireless LAN and/or Bluetooth>  
This product and your Health  
This product, like other radio devices, emits radio fre-  
quency electromagnetic energy. The level of energy emit-  
ted by this product however is far much less than the  
electromagnetic energy emitted by wireless devices like  
for example mobile phones.  
When using your telephone equipment, basic safety pre-  
cautions should always be followed to reduce the risk of  
fire, electric shock and injury to persons, including the fol-  
lowing:  
1. Do not use this product near water, for example, near  
a bath tub, wash bowl, kitchen sink or laundry tub, in a  
wet basement or near a swimming pool.  
5
 
Read Me First  
Because this product operates within the guidelines found in  
radio frequency safety standards and recommendations, we  
believe this product is safe for use by consumers. These  
standards and recommendations reflect the consensus of  
the scientific community and result from deliberations of pan-  
els and committees of scientists who continually review and  
interpret the extensive research literature.  
Bottom  
In some situations or environments, the use of this prod-  
uct may be restricted by the proprietor of the building or  
responsible representatives of the organization. These sit-  
uations may for example include:  
Precautions  
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS  
PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAF-  
FIC CONTROL EQUIPMENT/SYSTEMS, OR AIRCRAFT  
z Using this product on board of airplanes, or  
z In any other environment where the risk of interference  
to other devices or services is perceived or identified  
as harmful.  
If you are uncertain of the policy that applies on the use of  
wireless devices in a specific organization or environment  
(e.g. airports), you are encouraged to ask for authoriza-  
tion to use this product prior to turning on the product.  
*1  
COCKPIT EQUIPMENT/SYSTEMS . PANASONIC WILL  
NOT BE RESPONSIBLE FOR ANY LIABILITY RESULTING  
FROM THE USE OF THIS PRODUCT ARISING OUT OF  
THE FOREGOING USES.  
*1  
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2  
Electrical Flight Bag (EFB) Systems and Class1 EFB Systems  
when used during critical phases of flight (e.g., during take-off  
and landing) and/or mounted on to the aircraft. Class1 EFB Sys-  
tems and 2 EFB Systems are defined by FAA: AC (Advisory Cir-  
cular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets)  
No.36.  
Regulatory Information  
We are not responsible for any radio or television interfer-  
ence caused by unauthorized modification of this product.  
The correction of interference caused by such unautho-  
rized modification will be the responsibility of the user. We  
and its authorized resellers or distributors are not liable for  
damage or violation of government regulations that may  
arise from failing to comply with these guidelines.  
Panasonic cannot guarantee any specifications, tech-  
nologies, reliability, safety (e.g. Flammability/Smoke/  
Toxicity/Radio Frequency Emission, etc) requirements  
related to aviation standards that exceed the specifica-  
tions of our COTS (Commercial-Off-The-Shelf) prod-  
ucts.  
This computer is not intended for use in medical equip-  
ment including life-support systems, air traffic control sys-  
tems, or other equipment, devices or systems that are  
involved with ensuring human life or safety. Panasonic  
cannot be held responsible in any way for any damages  
or loss resulting from the use of this computer in these  
types of equipment, devices or systems, etc.  
CD/DVD Drive Caution  
CAUTION!  
THIS PRODUCT UTILIZES A LASER.  
USE OF CONTROLS, ADJUSTMENTS OR PERFOR-  
MANCE OF PROCEDURES OTHER THAN THOSE  
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS  
RADIATION EXPOSURE.  
DO NOT OPEN COVERS AND DO NOT REPAIR YOUR-  
SELF.  
REFER SERVICING TO QUALIFIED PERSONNEL.  
This computer has been designed so as to minimize  
shock to the LCD and hard disk drive, the leakage of liq-  
uid (e.g., water) on to the keyboard, etc., but no warranty  
is provided against such trouble. Therefore, as a precision  
instrument, be extremely careful in the handling.  
If a Malfunction Occurs, Immediately Unplug the AC  
Cord and the Battery Pack  
• Computer is damaged  
• Foreign object inside computer  
• Smoke emitted  
• Unusual smell emitted  
Laser safety information is appropriate only when drive  
with laser is installed.  
AVERTISSEMENT!  
CET APPAREIL UTILISE UN LASER.  
L’UTILISATION DE COMMANDES OU DE RÉGLAGES  
OU L’EXÉCUTION DE PROCÉDURES AUTRES QUE  
CELLES SPÉCIFIÉES ICI PEUVENT PROVOQUER  
UNE EXPOSITION À DES RADIATIONS  
DANGEREUSES.  
NE PAS OUVRIR LES COUVERCLES NI ESSAYER DE  
RÉPARER SOIMÊME.  
CONFIER TOUT TRAVAIL D’ENTRETIEN À UN  
PERSONNEL QUALIFIÉ.  
• Unusually hot  
Continuing to use the computer while any of the above  
conditions are present may result in fire or electric shock.  
• If a malfunction occurs, immediately turn the power off  
and unplug the AC cord, and then remove the battery  
pack.  
Do Not Touch the Computer and Cable When It Starts  
Thundering  
Electric shock may result.  
Les mesures de sécurité relatives au laser ne s’appli-  
quent que lors de l’installation d’une unité avec laser.  
6
 
Do Not Connect the AC Adaptor to a Power Source Do Not Keep the Computer Wherever There is a Lot of  
Other Than a Standard Household AC Outlet  
Water, Moisture, Steam, Dust, Oily Vapors, etc.  
Otherwise, a fire due to overheating may result. Connect- Otherwise, possibly resulting in fire or electric shock.  
ing to a DC/AC converter (inverter) may damage the AC  
adaptor. On an airplane, only connect the AC adaptor/  
charger to an AC outlet specifically approved for such  
use.  
Do Not Leave the Computer in High Temperature  
Environment Such as in a Sun-Heated Car, for a Long  
Period of Time  
Leaving the computer where it will be exposed to  
Do Not Do Anything That May Damage the AC Cord, extremely high temperatures such as in a sun-heated car  
the DC Plug, or the AC Adaptor  
or in direct sunlight may deform the cabinet and/or cause  
Do not damage or modify the cord, place it near hot tools, trouble in the internal parts. Continued use in such a  
bend, twist, or pull it forcefully, place heavy objects on it, resulting condition may lead to short-circuiting or insula-  
or bundle it tightly.  
tion defects, etc. which may in turn lead to a fire or electric  
Continuing to use a damaged cord may result in fire, short shocks.  
circuit, or electric shock.  
Do Not Block the Ventilation Hole  
Do Not Pull or Insert the DC Plug If Your Hands Are Otherwise, heat will build up inside, possibly resulting in a  
Wet  
fire.  
Electric shock may result.  
Hold the Plug When Unplugging the AC Cord  
Clean the DC Plug of Dust and Other Debris Regularly Pulling on the cord may damage the cord, resulting in a  
If dust or other debris accumulates on the plug, humidity, fire or electric shock.  
etc. may cause a defect in the insulation, which may result  
in a fire.  
• Pull the plug, and wipe it with a dry cloth.  
Pull the plug if the computer is not being used for a long  
Do Not Move the Computer While the DC Plug Is Con-  
nected  
The AC cord may be damaged, resulting in fire or electric  
shock.  
period of time.  
• If the AC cord is damaged, unplug the DC plug immedi-  
Insert the AC Plug Completely  
ately.  
If the plug is not inserted completely, fire due to overheat-  
ing or electric shock may result.  
• Do not use a damaged plug or loose AC outlet.  
Use Only the Specified AC Adaptor With Your Com-  
puter  
Using an AC adaptor other than the one supplied  
Do Not Place Containers of Liquid or Metal Objects on (attached to your computer or supplied by Panasonic)  
Top of the Computer  
may resulting in a fire.  
If water or other liquid spills, or if paper clips, coins, or for-  
eign matter get inside the computer, fire or electric shock  
may result.  
• If foreign matter has found its way inside, immediately  
turn the power off and unplug the AC cord, and then  
remove the battery pack. Then contact your technical  
support office.  
Do Not Subject the AC Adaptor to Any Strong Impact  
Using the AC adaptor after a strong impact such as being  
dropped may result in electric shock, short circuit, or fire.  
Take a Break of 10-15 Minutes Every Hour  
Using the computer for long periods of time may have det-  
rimental health effects on the eyes or hands.  
Do Not Look into the CD/DVD Drive  
Looking directly at the internal laser light source may  
result in damage to eyesight.  
Do Not Disassemble the Computer  
There are high-voltage areas inside which may give you  
an electric shock if you should touch them. Do not touch  
the pins and circuit boards inside, and do not allow foreign  
matter to enter inside.  
Do Not Use Disks That Are Cracked or Deformed  
Because the disks rotate at high speeds, damaged disks  
may break apart causing injury.  
Also, remodeling or disassembly may cause a fire.  
• Disks that are not round and disks that have been  
repaired using adhesives are similarly dangerous, and  
so should not be used.  
Keep SD Memory Cards Away from Infants and Small  
Children  
Accidental swallowing will result in bodily injury.  
In the event of accidental swallowing, see a doctor imme-  
diately.  
Do Not Turn the Volume Up to Loud When Using  
Headphones  
Listening at high volumes that overstimulate the ear for  
long periods of time may result in loss of hearing.  
Do Not Place the Computer on Unstable Surfaces  
If balance is lost, the computer may fall over or drop,  
resulting in an injury.  
Use the Modem with a Regular Telephone Line  
Connection to an internal phone line (on-premise  
switches) of a company or business office, etc. or to a dig-  
ital public phone or use in a country or area not supported  
by the computer may result in a fire or electric shocks.  
Avoid Stacking  
If balance is lost, the computer may fall over or drop,  
resulting in an injury.  
7
 
Read Me First  
Do Not Connect a Telephone Line, or a Network Cable Do Not Use with Exposing the Skin to the Computer  
Other Than the One Specified, into the LAN Port  
for a Long Period of Time  
If the LAN port is connected to a network such as the Using the computer with exposing the skin to the heat  
ones listed below, a fire or electric shock may result.  
• Networks other than 1000BASE-TX, 100BASE-TX or  
10BASE-T  
• Phone lines (Telephone lines, internal phone lines  
(onpremise switches), digital public phones, etc.)  
source of the computer or AC adaptor for a long period of  
time can cause a low-temperature burn.  
z Do not place the computer near a television or radio  
receiver.  
z Keep the computer away from magnets. Data stored  
on the hard disk may be lost.  
Precautions (Battery Pack)  
Do Not Use with Any Other Computer  
The battery pack is rechargeable and was intended for  
the specified computer or charger. If it is used with a com-  
z This computer prevents overcharging of the battery by  
recharging only when the remaining power is less than  
approx. 95% of capacity.  
puter other than the one for which it was designed, elec- z The battery pack is not charged when the computer is  
trolyte leakage, generation of heat, ignition or rupture may  
result.  
first purchased. Be sure to charge it before using it for  
the first time. When the AC adaptor is connected to the  
computer, charging begins automatically.  
Do Not Charge the Battery Using the Methods Other  
Than Indicated in This Manual  
If the battery pack is not charged using one of the meth-  
ods indicated in this manual, electrolyte leakage, genera-  
tion of heat, ignition or rupture may result.  
z Should the battery leak and the fluid get into your  
eyes, do not rub your eyes. Immediately flush your  
eyes with clear water and see a doctor for medical  
treatment as soon as possible.  
NOTE  
Do Not Throw the Battery Pack into a Fire or Expose It  
to Excessive heat  
z The battery pack may become warm during recharging  
or normal use. This is completely normal.  
z Recharging will not commence if internal temperature  
of the battery pack is outside of the allowable tempera-  
Generation of heat, ignition or rupture may result.  
Avoid Extreme Heat (Near the Fire, in Direct Sunlight,  
for Example)  
Electrolyte leakage, generation of heat, ignition or rupture  
may result.  
ture range (0 °C to 50 °C {32°F to 122°F}) (Î  
Ref-  
erence Manual “Battery Power”). Once the allowable  
range requirement is satisfied, charging begins auto-  
matically. Note that the recharging time varies based  
on the usage conditions. (Recharging takes longer  
than usual when the temperature is 10 °C {50°F} or  
below.)  
Do Not Insert Sharp Objects into the Battery Pack,  
Expose It to Bumps or Shocks, Disassemble, or Mod-  
ify It  
Electrolyte leakage, generation of heat, ignition or rupture  
may result.  
z If the temperature is low, the operating time is short-  
ened. Only use the computer within the allowable tem-  
perature range.  
z This computer has a high temperature mode function  
that prevents the degradation of the battery in high  
Do Not Short the Positive (+) and Negative (-) Con-  
tacts  
Generation of heat, ignition or rupture may result. Do not  
place the battery pack together with articles such as neck-  
laces or hairpins when carrying or storing.  
temperature environments. (Î  
Reference Manual  
“Battery Power”) A level corresponding to a 100%  
charge for high temperature mode is approximately  
equivalent to an 80% charge level for normal tempera-  
ture mode.  
Do Not Use This Computer with a Battery Pack Other  
Than the One Specified  
Use only the specified battery pack (CF-VZSU29A) with  
your CF-51. Use of battery packs other than those manu-  
factured and supplied by Panasonic may present a safety  
hazard (generation of heat, ignition or rupture).  
z The battery pack is a consumable item. If the amount  
of time the computer can be run by using a particular  
battery pack becomes dramatically shorter and  
repeated recharging does not restore its performance,  
the battery pack should be replaced with a new one.  
z When transporting a spare battery inside a package,  
briefcase, etc., it is recommended that it be placed in a  
plastic bag so that its contacts are protected.  
z Do not touch the terminals on the battery pack. The  
battery pack may no longer function properly if the  
contacts are dirty or damaged.  
z Do not expose the battery pack to water, or allow it to  
become wet.  
z If the battery pack will not be used for a long period of  
time (a month or more), charge or discharge (use) the  
battery pack until the remaining battery level becomes  
30% to 40% and store it in a cool, dry place.  
z Always power off the computer when it is not in use.  
Leaving the computer on when the AC adaptor is not  
connected will exhaust the remaining battery capacity.  
8
 
Description of Parts  
A : Speaker  
Hard disk drive status  
Î
Reference Manual “Key Combinations”  
Power status  
B : Ventilation hole  
C : DC-IN jack  
D : USB port  
(Off: Power off/Hibernation, Green: Power on,  
Blinking green: Standby, Blinking green rapidly:  
Cannot power on or resume due to low tempera-  
ture.)  
Î
Reference Manual “USB Devices”  
Battery status  
E : IEEE 1394 interface connector  
Î
Reference Manual “Battery Power”  
Î
Reference Manual “IEEE 1394 Devices”  
SD Memory Card status  
(Blinking: During access or a password is  
requested)  
F : PC Card slot  
Î
Reference Manual “PC Cards”  
G : Security lock  
Î
Reference Manual “SD Memory Card”  
You can connect a Kensington cable. Refer to the  
instruction manual of the cable.  
L : Power button  
M : Function key  
H : Wireless LAN antenna  
<Only for model with wireless LAN>  
Î
Reference Manual “Key Combinations”  
N : Bluetooth antenna  
Î
Reference Manual “Wireless LAN”  
<Only for model with Bluetooth>  
I : Smart Card slot  
<Only for model with Smart Card slot>  
Î
Reference Manual “Bluetooth”  
O : Keyboard  
Î
Reference Manual “Smart Card”  
P : SD Memory Card slot  
J : LCD  
K : LED indicator  
Î
Reference Manual “SD Memory Card”  
Q : Headphone jack  
Caps lock  
You can connect headphones or amplified speakers.  
When they are connected, audio from the internal  
speakers is not heard.  
Numeric key (NumLk)  
Scroll lock (ScrLk)  
Multimedia pocket device status or the second  
battery status  
R : Microphone jack  
You can use a stereo condenser microphone. Con-  
necting other type of microphone may interrupt audio  
input or may cause a malfunction.  
Î
Reference Manual “Multimedia Pocket”  
“Battery Power”  
S : Touch pad  
CAUTION  
z Do not put a metallic object or magnetic media close to the speakers.  
9
 
Description of Parts  
A : Serial port  
I : Multimedia pocket release button  
B : Modem port  
Î
Reference Manual “Multimedia Pocket”  
Î
Reference Manual “Modem”  
J : Expansion bus connector  
C : Ventilation hole  
D : USB port  
Î
Reference Manual “Port Replicator”  
K : RAM module slot  
Î
Reference Manual “USB Devices”  
Î
Reference Manual “RAM Module”  
E : External display port  
L : Hard disk drive  
Î
Reference Manual “External Display”  
Î
Reference Manual “Hard Disk Drive”  
F : External keyboard/Mouse port  
G : LAN port  
M : Battery latch  
N : Hard disk drive latch  
Î
Reference Manual “LAN”  
Î
Reference Manual “Hard Disk Drive”  
H : Multimedia pocket  
O : Battery pack  
Î
Reference Manual “Multimedia Pocket”  
CAUTION  
z Do not block the ventilation hole with a thick cloth etc. Select a position with good ventilation.  
A lithium ion battery that is recyclable powers the product you have purchased.  
Please call 1-800-8-BATTERY for information on how to recycle this battery.  
L’appareil que vous vous êtes procuré est alimenté par une batterie au lithium-ion.  
Pour des renseignements sur le recyclage de la batterie, veuillez composer le  
1-800-8-BATTERY.  
10  
 
First-time Operation  
Preparation  
A Check and identify the supplied accessories.  
If you do not find the described accessories, contact Panasonic Technical Support (Î page 29).  
• AC Adaptor . . . . . . 1  
• AC Cord . . . . . . . . . 1  
• Battery Pack . . . . . 1  
Model No: CF-VZSU29A  
Model No: CF-AA1683A (Models for U.S.A)  
CF-AA1653A (Models for Canada)  
• Modem Telephone  
Cable . . . . . . . . . . . 1  
• Product Recovery DVD-ROM . . . . . . . . . . . . . . 1  
• Operating Instructions (This book) . . . . . . . . . 1  
®
• Windows Book . . . . . . . . . . . . . . . . . . . . . . . . . 1  
z You will need the serial number when you reinstall B’s Recorder/B’s CLiP using Product Recovery DVD-ROM  
B
Read the LIMITED USE LICENSE AGREEMENT before breaking the seal on the computer’s packaging (  
page 24).  
1
1
Insert the battery pack.  
A Press and hold the  
mark part (A), and slide and remove the cover.  
B Insert the battery pack (B) until it securely fits the connector.  
A
C Slide the cover back.  
To remove the battery pack  
In step above, slide and hold the latch (C), and pull the tab (D) of the battery pack.  
B
CAUTION  
B
z Be careful not to catch the tab when you close the cover.  
z Make sure the cover is securely attached. Otherwise the battery pack may fall  
when you carry the computer.  
z Do not touch the terminals of the battery pack and the computer. Doing so can  
make the terminals dirty or damaged, and may cause malfunction of the battery  
pack and the computer.  
z Use only the specified battery pack (CF-VZSU29A) with your computer. If you  
use the former type of battery (CF-VZSU29), the computer’s processing speed  
will become slower.  
z The computer’s processing speed will become slower when the computer oper-  
ates by the second battery pack.  
C
D
2
Connect your computer to a power outlet.  
2
The battery charging starts automatically.  
CAUTION  
z Do not disconnect the AC adaptor until the first-time operation procedure is com-  
pleted.  
z When using the computer for the first time, do not connect any peripheral device  
except the battery pack and AC adaptor.  
z Handling the AC adaptor  
• Do not twist or pull the AC power cord forcefully. Doing so may damage the  
connections.  
• Use only the specified AC adaptor with your computer. Using an AC adaptor  
other than the one supplied might damage the battery and/or the computer.  
• When the DC plug is not connected to the computer, disconnect the AC cord  
from your AC wall outlet.  
• Problems such as sudden voltage drops may arise during periods of thunder and  
lightning. Since this could adversely affect your computer, an uninterruptible power  
source (UPS) is highly recommended unless running from the battery pack alone.  
11  
 
   
First-time Operation  
3
Turn on the computer.  
3
A Slide the latch (A), and open the display.  
B Press and hold the power button  
power indicator lights.  
for approximately one second until the  
A
CAUTION  
z Do not press the power button repeatedly.  
z The computer will be forcibly turned off if you press and hold the power button for  
four seconds or longer.  
z Once you turn off the computer, wait for ten seconds or more before you turn on  
the computer again.  
z Do not perform the following operation until the hard disk drive indicator  
turns off.  
• Connecting or disconnecting the AC adaptor  
• Pressing the power button  
Touching the keyboard, touch pad or external mouse  
• Closing the display  
z When the CPU temperature is high, the computer may not start up to prevent  
overheating of the CPU. Wait until the computer cools down, and then turn the  
power on again. If the computer does not power on even after cooling down,  
contact Panasonic Technical Support (Î page 29).  
4
Setup Windows.  
A Follow the on-screen instructions.  
CAUTION  
z When you set date/time/time zone and click [Next], the screen may not go to the  
next step for a few minutes. Do not touch the keyboard or touch pad, and wait  
until the screen changes.  
z If “An unexpected error has occurred …” (or a similar message) is displayed,  
select [OK]. This is not a malfunction.  
z Wait until the hard disk drive indicator  
has turned off.  
5
Create a new account.  
A Click [start] - [Control Panel] - [User Accounts] - [Create a new account].  
CAUTION  
z Remember your password. If you forget the password, you cannot use the Win-  
dows operation system. Creating a password reset disk beforehand is recom-  
mended.  
NOTE  
z Regarding Windows XP  
You can select the Classic view of Control Panel or the Classic Start menu. You can also change the way a user logs  
on or off. This manual explains using the Windows XP default setting (not Classic view or Classic Start menu etc.).  
z Windows Update  
You can update to the latest patches and service packs for Windows with the following menus.  
Click [start] - [All Programs] - [Windows Update].  
Do not apply “Driver Updates” even if a message to update a driver appears. If a driver update is required,  
contact Panasonic Technical Support (Î page 29).  
z If the message “Your computer might be at risk” is displayed  
Select  
on the taskbar and make the appropriate settings. The Windows Security Center regularly gives you  
notice so that you can make the optimum settings.  
This is not an error message and you can use the computer. However, making appropriate measures is recom-  
mended to reduce the risk of virus and other attacks.  
z Note that the computer consumes electricity even when the computer power is off.  
If the battery pack is fully charged, the battery will fully discharge in Approx. 3 weeks. (When second battery pack is  
attached: Approx. 4 weeks)  
12  
 
z To conserve power, the following power saving methods are set at the time of purchase.  
• The screen automatically turns off after 15 minutes of inactivity.  
• The computer goes automatically into standby mode after 20 minutes of inactivity.  
*1  
Refer to  
Reference Manual “Standby or Hibernation Functions” of your computer about resuming from standby.  
z Power Consumption in each mode is as follows.  
When the screen is off: 19 W  
In standby: 2.4 W  
The battery pack is fully charged (or not being charged) and the computer is off: 0.9 W  
z Note that the computer consumes electricity even when the computer power is off. If the battery pack is fully  
charged, the battery will be fully discharged in the following period of time:  
When power is off: 3 weeks  
In standby: 3 days  
In hibernation: 3 days  
If “Wake up from LAN” is disabled, the period of time in standby will become slightly longer, and the period of time in  
hibernation will become about the same as during power-off.  
13  
 
 
On-screen Manual  
You can access the Reference Manual and the Important Tips on the computer screen.  
When you access the Reference Manual and the Important Tips for the first time, the License Agreement of the Adobe  
Reader may be displayed. Read it carefully and select [Accept] to proceed.  
Reference Manual  
The Reference Manual contains the practical information to help you fully enjoy the computer’s performance.  
To access the Reference Manual:  
A Click [start] - [Reference Manual].  
Contents  
z Key Combinations  
z Standby/Hibernation Functions  
z Security Measures  
z Battery Power  
z Multimedia Pocket  
z CD/DVD Drive  
z WinDVD  
z B’s Recorder/B’s CLiP  
z PC Cards  
z SD Security  
z Smart Card  
z RAM Module  
z Port Replicator  
z External Display  
z USB Devices  
z IEEE 1394 Devices  
z Modem  
z Bluetooth  
z Wireless Switch Utility  
z Hard Disk Drive  
z Setup Utility  
z Icon Enlarger  
z Loupe Utility  
z DMI Viewer  
z Technical Information  
z Troubleshooting (Advanced)  
z LAN  
z SD Memory Card  
z Wireless LAN  
NOTE  
z In the  
Reference Manual “LAN”, the procedure for “Enabling the Wake Up from LAN function” is described. But  
“Wake Up from LAN” is enabled at the time of purchase. “The Wake Up from LAN” function can be switched to  
enable/disable on the “Power Management” screen, which is described in the  
“Enabling the Wake Up from LAN function”.  
Reference Manual “LAN” -  
Important Tips  
The Important Tips will provide you with the battery information so that you can use the battery pack in the optimum  
condition to obtain longer operation time.  
To access the Important Tips:  
A Double-click  
on the desktop.  
z Alternatively click [start] - [All Programs] - [Panasonic] - [On-Line Manuals] - [Important Tips].  
14  
 
   
Handling and Maintenance  
Operation Environment  
z Place the computer on a flat stable surface. Do not place the computer upright or turn it over. If the computer is  
exposed to an extremely strong impact, it may become inoperable.  
z Temperature:  
Operation : 5 °C to 35 °C {41 °F to 95 °F}  
Storage : -20 °C to 60 °C {- 4 °F to 140 °F}  
Operation : 30% to 80% RH (No condensation)  
Storage : 30% to 90% RH (No condensation)  
Humidity:  
Even within the above temperature/humidity ranges, using for a long time in an extreme environment will result in  
the product deterioration and will shorten the product life.  
z Do not place the computer in the following areas, otherwise the computer may be damaged.  
• Near electronic equipment. Image distortion or noise may occur.  
• In extremely high or low temperature.  
z As the computer can become hot during operation, keep it away from items that are sensitive to heat.  
Handling Cautions  
This computer is designed to minimize shock to parts such as the LCD and the hard disk drive, but no warranty is pro-  
vided against any trouble caused by shock. Be extremely careful when handling the computer.  
z When carrying the computer:  
• Turn off the computer.  
• Remove all external devices, cables, PC Cards and other protruding things.  
• Remove a disc in the CD/DVD drive.  
• Do not drop or hit the computer against solid objects.  
• Do not leave the display open.  
• Do not grip the display part.  
z Do not put anything (e.g., a piece of paper) between the display and keyboard.  
z When you board an airplane, take the computer with you and never put it in your checked luggage. When using the  
computer on airplane, follow the airline’s instructions.  
z When carrying a spare battery, put it in a plastic bag to protect its terminals.  
z The touch pad is designed to be used with a finger tip. Do not place any object on its surface and do not press down  
strongly with sharp-pointed or hard objects that may leave marks (e.g., nails, pencils and ball point pens).  
z Avoid any harmful substances such as oil from getting into the touch pad. The cursor may not work correctly.  
When using peripheral devices  
Follow these instructions and the Reference Manual to avoid any damage to the devices. Carefully read the instruction  
manuals of the peripheral devices.  
z Use the peripheral devices conforming to the computer’s specifications.  
z Connect to the connectors in the correct direction.  
z If it is hard to insert, do not try forcibly but check the connector’s shape, direction, alignment of pins, etc.  
z If screws are included, fasten them securely.  
z Remove the cables when you carry the computer. Do not pull the cables forcibly.  
Preventing your computer from unauthorized use via wireless LAN  
<Only for model with wireless LAN>  
z Before using wireless LAN, make the appropriate security settings such as data encryption.  
15  
 
 
Handling and Maintenance  
Maintenance  
To clean the LCD panel  
z Do not use water to clean the panel. Ingredients included in water may leave scratches and reduce readability of the  
screen.  
z To remove dust or dirt, do not use a cloth to rub it off since it may leave scratch on the screen.  
Use a fine brush to sweep dust or dirt, then wipe with a dry soft glass-cleaning cloth.  
z To clean the oily surface, use a soft gauze dipped in camera lens cleaner, and then wipe with a dry soft glass-clean-  
ing cloth.  
To clean areas other than the LCD panel  
Wipe with a soft dry cloth such as gauze. When using detergent, dip a soft cloth in water-diluted detergent and wring it  
thoroughly.  
CAUTION  
z Do not use benzene, thinner, or rubbing alcohol since it may adversely affect the surface causing discoloration, etc.  
Do not use commercially-available household cleaners and cosmetics, as they may contain components harmful to  
the surface.  
z Do not apply water or detergent directly to the computer, since liquid may enter inside of the computer and cause  
malfunction or damage.  
16  
 
Hard Disk Data Erase Utility  
When disposing the computer or transferring the ownership, erase all hard disk data in order to avoid data leakage.  
Even if you erase the data or initialize the hard disk using normal Windows commands, the data can be read with some  
special software. Use the hard disk data erase utility to erase the data completely.  
Note that transferring of the ownership without uninstalling the commercial software will be a violation of the software’s  
license agreement.  
The hard disk data erase utility erases the data using overwriting method. If a malfunction or other operational error  
occurs during the erasing process, the data may not be completely erased. Also there may be special devices to read  
the erased data. To erase highly confidential data, ask a specialized company. Matsushita Electric Industrial Co., Ltd.  
will bear no responsibility for losses or damages suffered as a result of the use of this utility.  
Preparation  
z Prepare the following items:  
• The Product Recovery DVD-ROM (included)  
• Panasonic CD/DVD drive  
z Remove all peripherals (except for the CD/DVD drive).  
z Connect the AC adaptor and do not remove it until hard disk data erase is complete.  
NOTE  
z Even if hard disk data erase is performed, the number of times of DVD’s region code setting will not be reset.  
1
2
Turn off the computer and insert the CD/DVD drive into the multimedia pocket  
Reference Manual “Multimedia Pocket”).  
(Î  
Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-  
played.  
The Setup Utility starts up.  
z If the password is requested, enter the Supervisor Password.  
3
Select the [Boot] menu, then select [IDE MP] and press F6 until [IDE MP] is at the top of  
the boot priority order.  
4
5
6
Select the [Security] menu and set [MP CD/DVD Operation] to [Enable].  
Set the Product Recovery DVD-ROM into the CD/DVD drive.  
Press F10  
.
At the confirmation message, select [Yes] and press Enter  
.
The computer restarts.  
7
Press  
2
to execute [2. [Erase HDD]].  
z To cancel this operation, press  
0.  
8
9
At the confirmation message, press  
Y.  
When [<<< Start menu >>>] is displayed, press Enter  
The approximate time required for erasing data will be displayed.  
.
10 Press Space  
.
At the confirmation message, press Enter  
.
The hard disk erase process starts. When the operation is completed, the [Hard disk data has been deleted.]  
message will appear. If a problem has occurred during the operation, an error message will appear.  
z To cancel partway, press Ctrl  
+
C. The data erasure will be up to that point.  
11 Remove the Product Recovery DVD-ROM, and then press any key to turn off the com-  
puter.  
17  
 
 
Reinstalling Software  
When you reinstall the software, the hard disk data will be erased. Back up important data before reinstallation.  
Reinstalling software will return the computer to the default condition. Even if the data is stored in partitions on the  
hard disk, it may be erased or corrupted.  
Preparation  
z Prepare the following items:  
• The Product Recovery DVD-ROM (included)  
• Panasonic CD/DVD drive  
z Remove all peripherals (except for the CD/DVD drive).  
z Connect the AC adaptor and do not remove it until reinstallation is complete.  
NOTE  
z Even if reinstallation is performed, the number of times of DVD’s region code setting will not be reset.  
1
2
Turn off the computer and insert the CD/DVD drive into the multimedia pocket  
Reference Manual “Multimedia Pocket”).  
(Î  
Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-  
played.  
The Setup Utility starts up.  
z If the password is requested, enter the Supervisor Password.  
3
4
Write down all of the contents of the Setup Utility and press F9.  
At the confirmation message, select [Yes] and press Enter  
.
Select the [Boot] menu, then select [IDE MP] and press F6 until [IDE MP] is at the top of  
the boot priority order.  
5
6
7
Select the [Security] menu and set [MP CD/DVD Operation] to [Enable].  
Set the Product Recovery DVD-ROM into the CD/DVD drive.  
Press F10  
.
At the confirmation message, select [Yes] and press Enter  
.
The computer will restart.  
8
9
Press  
1
to execute [1. [Recovery]].  
The License Agreement screen appears.  
z To cancel partway, press  
0
.
Press  
1
to select [1. Yes, I agree to the provisions above and wish to continue!].  
10 Select the settings.  
z [2]: Enter the size of operating system partition and press Enter  
.
(The size of data partition will be determined by subtracting the operating system partition size from the  
maximum size.)  
[3]: Windows will be installed in the first partition.  
(The size of the first partition must be 20 GB or more. If smaller, installation will not be possible.)  
At the confirmation message, press  
Y.  
Reinstallation starts automatically. (It will take approximately 25 - 50 minutes.)  
z Do not interrupt reinstallation, for example by turning off the computer or pressing Ctrl  
+
Alt + Del. Other-  
wise reinstallation may become unavailable as Windows may not start up or the data may be corrupted.  
11 Remove the Product Recovery DVD-ROM, and then press any key to turn off the com-  
puter.  
12 Turn on the computer, and press F2 several times while [Panasonic] boot screen is dis-  
played.  
The Setup Utility starts up.  
z If the password is requested, enter the Supervisor Password.  
13 Press F9  
.
At the confirmation message, select [Yes] and then press Enter  
.
The Setup Utility settings excluding the password(s) will return to the default values.  
18  
 
   
14 Select the [Exit] menu and then select [Save Current Values], then press Enter  
.
At the confirmation message, select [Yes] and press Enter  
.
15 Turn the computer off by using the power button.  
z If additional instructions are included with the computer, be sure to read them. It may be necessary to perform  
additional operations during the following procedure.  
16 Perform the First-time Operation (Î page 11).  
17 Start the Setup Utility and change the settings as necessary.  
To change the drive letter of hard disk or CD/DVD drive  
NOTE  
z Drive letters can be changed only when two or more partitions have been created on the hard disk drive.  
z The name of the C: drive cannot be changed.  
z Change the drive letters before installing applications.  
A Click [start] - [Control Panel] - [Performance and Maintenance] - [Administrative Tools], and double-click [Com-  
puter Management].  
B Click [Disk Management] from [Storage].  
C Right-click the hard disk partition or the CD/DVD drive name, and click [Change Drive Letter and Paths...].  
D Click [Change...].  
E Click [Assign the following drive letter] and the new drive letter, and then click [OK].  
At the confirmation message, click [Yes].  
19  
 
Error Code/Message  
Follow the instructions below when an error message or code appears. If the problem persists or if the error code/mes-  
sage is not shown here, contact Panasonic Technical Support (Î page 29).  
Error Code/Message  
0211 Keyboard error  
Solution  
z Disconnect external keyboard or mouse.  
0251 System CMOS  
checksum bad -  
An error has occurred in the memory of Setup Utility settings. This occurs when the memory  
content is changed by an unexpected program operation, etc.  
Default configuration z Start the Setup Utility and return the settings to the default values, and then change the  
used  
settings as necessary.  
z If the problem persists, the internal clock battery may need to be replaced. Contact  
Panasonic Technical Support (Î page 29).  
0271 Check date and The date and time settings are not correct.  
time settings  
z Start the Setup Utility and set the correct date and time.  
z If the problem persists, the internal clock battery may need to be replaced. Contact  
Panasonic Technical Support (Î page 29).  
0280 Previous boot  
incomplete - Default  
configuration used  
Startup has failed repeatedly, so the Setup Utility settings have been returned to the default  
values to startup the computer.  
z Start the Setup Utility and return the settings to the default values, and then change the  
settings as necessary.  
Press <F2> to Setup  
z Write down the error details and press F2 to start the Setup Utility. Change the settings if  
necessary.  
Operating System not The operating system is not installed in the floppy disk or the hard disk that you are going to  
found  
boot from.  
z If using a floppy disk, change the disk to the one you can use for boot.  
z If using the hard disk, check if the hard disk is recognized in [Information] menu of the  
Setup Utility. If the hard disk is recognized, perform the reinstallation (Î page 18). If not,  
contact Panasonic Technical Support (Î page 29).  
z If a device is connected to the USB port, disconnect the device, or set [USB Port] or  
[Legacy USB Support] to [Disable] in [Advanced] menu of the Setup Utility.  
RAM Module Failed  
When the RAM module is not inserted correctly or the RAM module is not conforming to the  
computer’s specifications, so a beep will sound and the “RAM Module Failed” message will  
be displayed when you turn the power on.  
z Press the power button for four seconds or longer to turn off the computer, confirm that  
the RAM module conforms to the specifications, and reinsert it.  
To start the Setup Utility  
A Restart the computer.  
B Press F2 several times while [Panasonic] boot screen is displayed soon after the computer begins the startup  
procedure.  
20  
 
   
Troubleshooting (Basic)  
Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the  
“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact  
Panasonic Technical Support (Î page 29). You can also check the computer’s status in the PC Information Viewer  
(Î  
Reference Manual “Troubleshooting (Advanced)”).  
Starting Up  
Cannot start up.  
z Connect the AC adaptor.  
The power indicator or bat- z Insert a fully charged battery.  
tery indicator is not lit. z Remove the battery pack and the AC adaptor, then connect them again.  
z Remove the USB device, or set [USB Port] or [Legacy USB Support] to [Disable] in  
[Advanced] menu of the Setup Utility. The computer may not start up when certain  
USB devices are connected.  
The power is turned on but z The computer is warming up before start up. Wait for the computer to start up (takes  
“Warming up the system (up  
to 30 minutes)” appears.  
up to 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed  
to warm up and does not start. In this case, turn off the computer, leave it in an envi-  
ronment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on  
the power once more.  
Cannot turn on the computer. z Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour,  
The computer does not  
resume from standby mode.  
(The power indicator blinks  
quickly in green.)  
then turn on the power once more.  
You have forgotten the  
password.  
z Supervisor Password or User Password: Contact Panasonic Technical Support  
z Administrator password:  
• If you have a password reset disk, you can reset the administrator password. Set  
the disk and enter any wrong password, then follow the on-screen instructions and  
set a new password.  
• If you do not have a password reset disk, reinstall (Î page 18) and set up Win-  
dows, and then set a new password.  
“Remove disks or other  
media. Press any key to  
restart” or a similar mes-  
sage appears.  
z A floppy disk is in the drive and it does not contain system startup information.  
Remove the floppy disk and press any key.  
z This message may appear with some USB devices. Remove the USB device, or set  
[USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the  
Setup Utility.  
z If the problem persists after removing the disk, it may be a hard disk failure. Contact  
Panasonic Technical Support (Î page 29).  
Windows startup and opera- z Press F9 in the Setup Utility (Î page 20 “To start the Setup Utility”) to return the  
tion is slow.  
Setup Utility settings (excluding the passwords) to the default values. Start the  
Setup Utility and make the settings again. (Note that the processing speed depends  
on the application software, so this procedure may not make Windows faster.)  
z If you installed a resident software after purchase, turn off the residence.  
z Disable Indexing Service in the following menu.  
Click [start] - [Search] - [Change preferences] - [Without Indexing Service].  
The date and time are incor- z Make the correct settings. Click [start] - [Control Panel] - [Date, Time, Language,  
rect.  
and Regional Options] - [Date and Time].  
z If the problem persists, the internal clock battery may need to be replaced. Contact  
Panasonic Technical Support (Î page 29).  
z When the computer is connected to LAN, check the date and time of the server.  
z The 2100 A.D. or later year will not be correctly recognized on this computer.  
[Executing Battery Recali-  
bration] screen appears.  
z The Battery Recalibration was canceled before Windows was shut down last time.  
To start up Windows, turn off the computer by the power button, and then turn on.  
21  
 
 
Troubleshooting (Basic)  
Starting Up  
[Enter Password] does not  
appear when resuming from  
standby/hibernation.  
z To display [Enter Password] at resuming, set the Windows password. The password  
you have set in the Setup Utility is not requested at resuming.  
A Click [start] - [Control Panel] - [User Accounts] and select the account, and set  
the password.  
B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options]  
- [Advanced] and add a check mark for [Prompt for password when computer  
resumes from standby].  
Other startup problems.  
z Press F9 in the Setup Utility (Î page 20 “To start the Setup Utility”) to return the  
Setup Utility settings (excluding the passwords) to the default values. Start the  
Setup Utility and make the settings again.  
z Remove all peripheral devices.  
z Check to see if there was a disk error.  
A Click [start] - [My Computer] and right-click [Local Disk(C:)], and click [Proper-  
ties].  
B Click [Tools] - [Check Now].  
C Select the option in [Check disk options] and click [Start].  
z Start the computer in Safe Mode and check the error details. When the [Panasonic]  
boot screen disappears at startup, press and hold F8 until the Windows Advanced  
Options Menu is displayed.  
*1  
When [Password on boot] is set to [Enable] in the [Security] menu of the Setup Util-  
ity, [Enter Password] appears after the [Panasonic] boot screen disappears. As  
soon as you enter the password and press Enter, press and hold F8  
.
Display  
No display.  
z The external display is selected. Press Fn  
+
F3 to switch the display. Wait until the  
display has been switched completely before pressing Fn  
z When using an external display,  
• Check the cable connection.  
+
F3 again.  
• Turn on the display.  
• Check the settings of external display.  
z The display is turned off by the power-saving function. To resume, do not press the  
direct selection keys, but press any other key like Ctrl  
.
z The computer entered standby or hibernation by the power-saving function. To  
resume, press the power button.  
The screen is dark.  
z The screen is darker when the AC adapter is not connected. Press Fn  
+
F2 and  
adjust the brightness. As you increase the brightness, battery consumption  
increases.  
You can separately set the brightness for when the AC adaptor is connected and  
when not connected.  
The screen is disordered.  
z Changing the number of display colors and resolution may affect the screen. Restart  
the computer.  
z When using Simultaneous display, set the same display colors for the external dis-  
play as those for the LCD.  
®
<Only for model with Intel  
945GM chipset>  
z When using Simultaneous display, do not press Fn +F3.  
z Enable or disable Simultaneous display, and soon restart the computer.  
During Simultaneous dis-  
play, one of the screens  
becomes disordered.  
z When using the Extended Desktop, use the same display colors for the external dis-  
play as those used by the LCD.  
z If you continue to experience problems, try changing the display by clicking [start] -  
[Control Panel] - [Other Control Panel Options] - [Intel(R) GMA Driver for Mobile] -  
[Display Devices].  
®
<Only for model with Intel  
945GM chipset>  
z When the [Command Prompt] is set to “Full Screen” by pressing Alt  
picture is displayed on one of the screens only. When the window display is restored  
Enter, the picture is displayed on both screens.  
+
Enter, the  
by pressing Alt  
+
z Simultaneous display cannot be used until Windows startup is complete (during  
Setup Utility, etc.).  
22  
 
 
Display  
The external display does  
not work normally.  
z If the external display does not support the power saving function, it may not work  
normally when the computer enters the power saving mode. Turn off the external  
display.  
Shutting down  
Windows does not shut  
down.  
z Remove the USB device.  
z Wait one or two minutes. It is not a malfunction.  
Touch Pad  
The cursor does not work.  
z When using the external mouse, connect it correctly.  
z Restart the computer using the keyboard.  
(Press  
,
U, and  
R
to select [Restart].)  
z If the computer does not respond to keyboard commands, read “No response”  
(Î below).  
Cannot input using the  
touch pad.  
z Set [Touch Pad] to [Enable] in the [Main] menu of the Setup Utility.  
z The drivers for some mice may disable the touch pad. Check your mouse’s operat-  
ing instructions.  
Reference Manual  
The Reference Manual is  
not displayed.  
z Install Adobe Reader.  
A Log on to Windows as an administrator.  
B Click [start] - [Run], input [c:\util\reader\AdbeRdr70_enu_full.exe], then click  
[OK].  
C Follow the on-screen instructions.  
Reinstalling B’s Recorder/B’s CLiP  
A serial number is  
z Input the following serial number  
requested when reinstalling.  
B’s Recorder:  
B’s CLiP:  
Others  
No response.  
z Press Ctrl+Shift+Esc to open Task Manager and close the software application  
that is not responding.  
z An input screen (e.g., password input screen at startup) may be hidden behind  
another window. Press  
to check.  
Alt+Tab  
z Press the power button for four seconds or longer to shut down the computer, and  
then press the power button to turn it on. If the application program does not work  
normally, uninstall and reinstall the program. To uninstall, click [start] - [Control  
Panel] - [Add or Remove Programs].  
23  
 
 
LIMITED USE LICENSE AGREEMENT  
®
THE SOFTWARE PROGRAM(S) (“PROGRAMS”) FURNISHED WITH THIS PANASONIC PRODUCT (“PRODUCT”)  
ARE LICENSED ONLY TO THE END-USER (“YOU”), AND MAY BE USED BY YOU ONLY IN ACCORDANCE WITH  
THE LICENSE TERMS DESCRIBED BELOW. YOUR USE OF THE PROGRAMS SHALL BE CONCLUSIVELY  
DEEMED TO CONSTITUTE YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE.  
Matsushita Electric Industrial Co., Ltd. (“MEI”) has developed or otherwise obtained the Programs and hereby licenses  
their use to you. You assume sole responsibility for the selection of the Product (including the associated Programs) to  
achieve your intended results, and for the installation, use and results obtained therefrom.  
LICENSE  
A. MEI hereby grants you a personal, non-transferable and non-exclusive right and license to use the Programs in  
accordance with the terms and conditions stated in this Agreement. You acknowledge that you are receiving only a  
LIMITED LICENSE TO USE the Programs and related documentation and that you shall obtain no title, ownership  
nor any other rights in or to the Programs and related documentation nor in or to the algorithms, concepts, designs  
and ideas represented by or incorporated in the Programs and related documentation, all of which title, ownership  
and rights shall remain with MEI or its suppliers.  
B. You may use the Programs only on the single Product which was accompanied by the Programs.  
C. You and your employees and agents are required to protect the confidentiality of the Programs. You may not distrib-  
ute or otherwise make the Programs or related documentation available to any third party, by time-sharing or other-  
wise, without the prior written consent of MEI.  
D. You may not copy or reproduce, or permit to be copied or reproduced, the Programs or related documentation for  
any purpose, except that you may make one (1) copy of the Programs for backup purposes only in support of your  
use of the Programs on the single Product which was accompanied by the Programs. You shall not modify, or  
attempt to modify, the Programs.  
E. You may transfer the Programs and license them to another party only in connection with your transfer of the single  
Product which was accompanied by the Programs to such other party. At the time of such a transfer, you must also  
transfer all copies, whether in printed or machine readable form, of every Program, and the related documentation,  
to the same party or destroy any such copies not so transferred.  
F. You may not remove any copyright, trademark or other notice or product identification from the Programs and you  
must reproduce and include any such notice or product identification on any copy of any Program.  
YOU MAY NOT REVERSE ASSEMBLE, REVERSE COMPILE, OR MECHANICALLY OR ELECTRONICALLY TRACE  
THE PROGRAMS, OR ANY COPY THEREOF, IN WHOLE OR IN PART.  
YOU MAY NOT USE, COPY, MODIFY, ALTER, OR TRANSFER THE PROGRAMS OR ANY COPY THEREOF, IN  
WHOLE OR IN PART, EXCEPT AS EXPRESSLY PROVIDED IN THE LICENSE.  
IF YOU TRANSFER POSSESSION OF ANY COPY OF ANY PROGRAM TO ANOTHER PARTY, EXCEPT AS PER-  
MITTED IN PARAGRAPH E ABOVE, YOUR LICENSE IS AUTOMATICALLY TERMINATED.  
TERM  
This license is effective only for so long as you own or lease the Product, unless earlier terminated. You may terminate  
this license at any time by destroying, at your expense, the Programs and related documentation together with all cop-  
ies thereof in any form. This license will also terminate effective immediately upon occurrence of the conditions thereof  
set forth elsewhere in this Agreement, or if you fail to comply with any term or condition contained herein. Upon any  
such termination, you agree to destroy, at your expense, the Programs and related documentation together with all cop-  
ies thereof in any form.  
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, UNDERSTAND IT AND AGREE TO BE BOUND  
BY ITS TERMS AND CONDITIONS. YOU FURTHER AGREE THAT IT IS THE COMPLETE AND EXCLUSIVE STATE-  
MENT OF THE AGREEMENT BETWEEN US, WHICH SUPERSEDES ANY PROPOSAL OR PRIOR AGREEMENT,  
ORAL OR WRITTEN, AND ANY OTHER COMMUNICATIONS BETWEEN US, RELATING TO THE SUBJECT MAT-  
TER OF THIS AGREEMENT.  
®
About Intel software products  
The enclosed software products and documentation were developed at private expense, and are provided with  
“RESTRICTED RIGHTS.” Use, duplication or disclosure by the government is subject to restrictions as set forth in  
FAR 52.227-14 and DFARS 252.227-7013 et. seq. or its successor. The use of this product by the government  
constitutes acknowledgment of Intel’s proprietary rights in the product.  
24  
 
   
Contrat de licence d’usage limité  
®
Le(s) logiciel(s) (les “Logiciels”) fournis avec ce produit Panasonic (le “Produit”) sont exclusivement concédés en  
licence à l’utilisateur ultime (“vous”), et ils ne peuvent être utilisés que conformément aux clauses contractuelles  
cidessous. En utilisant les logiciels, vous vous engagez de manière définitive à respecter les termes, clauses et  
conditions  
des présentes.  
Matsushita Electric Industrial Co., Ltd. (“MEI”) a mis au point ou obtenu les Logiciels et vous en concède l’utilisation par  
les présentes. Vous assumez l’entière responsabilité du choix de ce Produit (y compris des Logiciels associés) pour  
obtenir les résultats escomptés, ainsi que de l’installation, de l’utilisation et des résultats obtenus.  
Licence  
A. MEI vous octroie par les présentes le droit et la licence personnels, non cessibles et non exclusifs d’utiliser les  
Logiciels conformément aux termes, clauses et conditions de ce contrat. Vous reconnaissez ne recevoir qu’un droit  
limité d’utiliser les Logiciels et la documentation les accompagnant et vous vous engagez à n’obtenir aucun droit de  
titre, propriété ni aucun autre droit vis-à-vis des Logiciels et de la documentation les accompagnant ni vis-à-vis des  
algorithmes, concepts, dessins, configurations et idées représentés par ou incorporés dans les Logiciels et la  
documentation les accompagnant, dont les titres, la propriété et les droits resteront tous à MEI ou à leurs  
propriétaires.  
B. Vous ne pouvez utiliser les Logiciels que sur le Produit unique qui est accompagné par les Logiciels.  
C. Vous et vos employés ou agents êtes requis de protéger la confidentialité des Logiciels. Vous ne pouvez ni  
distribuer ni mettre les Logiciels et la documentation les accompagnant à la disposition d’un tiers, par partage de  
temps ou de quelque autre manière que ce soit, sans l’autorisation écrite préalable de MEI.  
D. Vous ne pouvez ni copier ni reproduire ni permettre la copie ni la reproduction des Logiciels ni de la documentation  
les accompagnant pour quelque fin que ce soit, à l’exception d’une (1) copie des Logiciels à des fins de sauvegarde  
uniquement pour soutenir votre utilisation des Logiciels sur le Produit unique qui est accompagné par les Logiciels.  
Vous ne pouvez ni modifier ni tenter de modifier les Logiciels.  
E. Vous ne pouvez céder les Logiciels et en octroyer la licence à une autre partie qu’en rapport avec votre cession du  
Produit unique qui est accompagné par les Logiciels à cette autre partie. Au moment de cette cession, vous devez  
céder également toutes les copies, que ce soit sous forme imprimée ou lisible par la machine, de tous les Logiciels  
ainsi que de la documentation les accompagnant, à la même partie ou détruire les copies non cédées.  
F. Vous ne pouvez retirer aucune marque de droits d’auteur, marque de commerce ou autre ni aucune identification de  
produit des Logiciels et vous devez reproduire et inclure toutes ces notices ou identifications de produit sur toutes  
les copies des Logiciels.  
Vous ne pouvez assembler en sens inverse, compiler en sens inverse ni retracer les Logiciels ni aucune de leurs  
copies, de façon électronique ou mécanique, en tout ou en partie.  
Vous ne pouvez utiliser, copier, modifier, altérer ni céder les Logiciels ni aucune de leurs copies, en tout ou en partie, à  
l’exception de ce qui est expressément stipulé dans ce contrat.  
Si vous cédez la possession de toute copie ou de tout Logiciel à une autre partie, à l’exception de ce qui est autorisé au  
paragraphe E ci-dessus, votre licence est automatiquement résiliée.  
Termes, clauses et conditions  
Cette licence n’est effective que pour la durée de possession ou de crédit-bail du Produit, à moins d’une résiliation  
antérieure. Vous pouvez résilier cette licence à tout moment en détruisant, à vos frais, les Logiciels et la documentation  
les accompagnant avec toutes leurs copies, sous quelque forme que ce soit. Cette licence sera également résiliée,  
avec application immédiate, si les conditions de résiliation définies ailleurs dans ce contrat se sont réalisées ou si vous  
ne respectez pas les termes, clauses et conditions qui y sont contenues. Au moment de la résiliation, vous acceptez de  
détruire, à vos frais, les Logiciels et la documentation les accompagnant avec toutes leurs copies, sous quelque forme  
que ce soit.  
Vous reconnaissez avoir lu ce contrat, en avoir compris toute la substance et avoir accepté de respecter ses termes,  
clauses et conditions. Vous reconnaissez en outre qu’ils sont la description complète et exclusive du contrat conclu  
entre nous, contrat qui remplace et annule toute proposition ou contrat précédent, écrit ou oral, et toute autre  
communication entre nous, relativement à l’objet du présent contrat.  
25  
 
Specifications  
This page provides the specifications for the basic model CF-51PF66EBM. The model number is different according to  
the unit configuration.  
z To check the model number:  
Check the bottom of the computer or the box the computer came in at the time of purchase.  
z To check CPU speed, memory size and the hard disk drive (HDD) size:  
Run the Setup Utility (Î  
Reference Manual “Setup Utility”) and select [Information] menu.  
[CPU Speed]: CPU speed, [System Memory]: Memory size, [Primary Master]: Hard disk drive size  
Main Specifications  
Model No.  
CPU  
CF-51PF66EBM  
®
Intel Core™ Duo Processor T2500 (2 GHz, 2 MB L2 cache, 667 MHz FSB)  
®
Chipset  
Intel 945PM  
Memory  
2048 MB (4096 MB Max.)  
128 MB  
Video Memory  
80 GB  
Hard Disk Drive  
720 KB/1.44 MB (two-mode)  
Floppy Disk Drive  
CD/DVD Drive  
Display Method  
15.0 UXGA type (TFT)  
65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1600 × 1200 dots)  
Internal LCD  
65,536/16,777,216 colors (800 × 600 dots/1024 × 768 dots/1280 × 1024 dots/1600 × 1200 dots/  
2048 × 1536 dots)  
External Display  
Wireless LAN  
Version 2.0+EDR  
Bluetooth  
LAN  
IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3ab 1000Base-T  
Modem  
Sound  
Data: 56 kbps (V.92) FAX: 14.4 kbps  
®
WAVE and MIDI playback, Stereo speaker, Intel High Definition Audio subsystem support  
Security Chip  
TPM (TCG V1.2 compliant)  
Card  
Slot  
PC Card  
Type I or Type II x 2, or Type III x 1 (3.3 V: 400 mA, 5 V: 400 mA)  
SD Memory  
x 1 (Data transfer rate = 8 MB per second  
)
Card  
x 1  
Smart Card  
RAM Module Slot  
Interface  
200-pin, SO-DIMM, PC2-4200 DDR2 SDRAM  
USB port (4-pin, USB 2.0) x 4, Serial Port (Dsub 9-pin male), Modem port (RJ-11), LAN port (RJ-45),  
External display port (Mini Dsub 15-pin female), External keyboard/ Mouse port (Mini DIN 6-pin female),  
Expansion Bus Connector (Dedicated 100-pin female), IEEE1394a Interface Connector (4-pin × 1),  
Microphone Jack (Miniature jack, 3.5 DIA, Stereo), Headphone Jack (Miniature jack, 3.5 DIA, Impedance  
32 Ω, Output Power 4 mW × 2, Stereo)  
Keyboard / Pointing Device 87 keys / Touch Pad  
Power Supply  
AC adaptor or Battery pack  
Input: 100 V to 240 V AC, 50 Hz/60 Hz, Output: 15.6 V DC, 8.0 A  
AC Adaptor  
26  
 
Main Specifications  
Battery Pack  
Li-ion 11.1 V, 7.65 Ah  
Main Battery: Approx. 2 hours to 4 hours (Approx. 4 hours  
Operating Time  
)
Main Battery + Second Battery: Approx. 3.5 hours to 6.5 hours (Approx. 6 hours)  
Charging  
Power on Main Battery: Approx. 4.5 hours  
Main Battery + Second Battery: Approx. 7 hours  
Time  
Power off Main Battery: Approx. 4.5 hours  
Main Battery + Second Battery: Approx. 7 hours  
Clock Battery  
Coin type lithium battery 3.0 V  
Power Consumption  
Approx. 60 W / Approx. 90 W  
(Maximum when recharging in the ON state)  
Physical Dimensions  
(W × H × D)  
325 mm × 47 mm × 278 mm {12.8" × 1.9" × 10.9" }  
Weight  
Approx. 2.9 kg {Approx. 6.4 lb.} (excluding multimedia pocket device)  
Approx. 3.1 kg {Approx. 6.8 lb.} (including CD/DVD drive in the multimedia pocket)  
Operation Environment Temperature: 5 °C to 35 °C {41 °F to 95 °F}  
Humidity: 30% to 80% RH (No condensation)  
Storage Environment  
Temperature: -20 °C to 60 °C {-4 °F to 140 °F}  
Humidity: 30% to 90% RH (No condensation)  
®
®
Operating System  
Utility Programs  
Microsoft Windows XP Professional Service Pack 2 with Advanced Security Technologies  
DMI Viewer, Adobe Reader, PC Information Viewer, SD Utility, Icon Enlarger, Loupe Utility, WinDVD™ 5  
®
(OEM Version), B’s Recorder GOLD8 BASIC, B’s CLiP 6, Intel PROSet/Wireless Software , Wireless  
®
LAN Switch , Bluetooth™ Stack for Windows by TOSHIBA , Bluetooth Switch , Wireless Switch Util-  
ity, Hotkey Settings, Battery Recalibration, Infineon TPM Professional Package  
Setup Utility, Hard Disk Data Erase Utility  
*1  
1MB = 1,048,576 bytes  
*2  
*3  
When expanding memory, remove the RAM module that was inserted at the time of factory shipment, and insert two 2048 MB-RAM modules.  
You can physically expand the memory up to 4 GB, but the total amount of usable memory available will be less depending on the  
actual system configuration.  
*4  
*5  
1GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.  
The drives included in the computer cannot be inserted into the multimedia pocket simultaneously.  
1KB = 1,024 bytes  
1MB = 1,024,000 bytes. Your operating system or some application software will report as fewer MB.  
*6  
A 16,777,216 color display is achieved by using the dithering function.  
Maximum resolution depends on the specifications of the external display.  
Only for model with wireless LAN  
*7  
*8  
*9  
Only for model with Bluetooth  
*10  
For information on TPM, click [start] - [Run] and input “c:\util\drivers\tpm\README.pdf”, and refer to the Installation Manual of  
“Trusted Platform Module (TPM)”.  
*11  
*12  
This slot does not support the MultiMedia card.  
Operation has been confirmed for Panasonic SD Memory Cards with up to 2 GB capacity.  
Theoretical value and not the actual speed. The transfer rate does not become higher even if you use a card that supports the  
higher transfer rate.  
*13  
*14  
*15  
*16  
*17  
*18  
*19  
*20  
*21  
Only for model with Smart Card slot  
The AC adaptor is compatible with power sources up to 240  
Varies depending on the usage conditions.  
V
AC adaptor. The computer is supplied with a 125  
V
AC compatible AC cord.  
Measured using BatteryMark™ Version 4.0.1 (LCD brightness: Maximum - Minimum)  
2
Measured using MobileMark™ 2002 (LCD brightness: 60 cd/m )  
Approx. 0.9 W when the battery pack is fully charged (or not being charged) and the computer is OFF.  
Rated power consumption  
You need to install to use the feature.  
The Product Recovery DVD-ROM is required.  
27  
 
                                         
Specifications  
CD/DVD Drive  
CD/DVD Drive  
DVD MULTI Drive  
Data  
Transfer  
DVD-ROM: 8X (Max.), CD-ROM: 24X (Max.)  
Reading  
CD-R: 8X/8-12X/8-16X/8-24X  
CD-RW: 4X  
Writing  
Rate  
High-Speed CD-RW: 4X/8X/10X  
Ultra-Speed CD-RW: 8X/10X  
DVD-R: 1X/2X/2-4X/2-6X/2-8X  
DVD-RW: 1X/2X/2-4X  
DVD-RAM: 2X/3X/3-5X  
+R: 2.4X/2.4-4X/2.4-6X/2.4-8X  
+R DL: 2.4X  
+RW: 2.4X/2.4-4X  
Supported Reading  
Discs/For-  
DVD-ROM (4.7 GB, 8.5 GB, 9.4 GB, 17 GB), DVD-Video, DVD-R (1.4 GB, 3.95 GB, 4.7 GB),  
DVD-R DL (8.5 GB), DVD-RW (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB), DVD-RAM (1.4 GB,  
2.8 GB, 2.6 GB, 5.2 GB, 4.7 GB, 9.4 GB), +R (4.7 GB), +R DL (8.5 GB), +RW (4.7 GB),  
CD-Audio, CD-ROM, CD-R, Photo CD, Video CD, CD-RW, CD TEXT, CD-EXTRA  
*25  
mat  
Writing  
DVD-R (1.4 GB, 4.7 GB for General),  
DVD-RW (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB), DVD-RAM (1.4 GB, 2.8 GB, 4.7 GB, 9.4 GB),  
+R (4.7 GB), +R DL (8.5 GB), +RW (4.7 GB), CD-R, CD-RW  
*22  
The data transfer rate of DVD per 1X speed is 1,350 KB/s.  
The data transfer rate of CD per 1X speed is 150 KB/s.  
*23  
If an unbalanced disc (e.g., a disc with which the balance has been displaced from the center) is inserted, the speed may become  
slower if there are large vibrations while the disc is rotating.  
*24  
*25  
*26  
*27  
Depending on the disc, the writing speed may become slower.  
1GB = 1,000,000,000 bytes. Your operating system or some application software will report as fewer GB.  
Does not support DVD-RW Ver.1.0.  
DVD-RAM: Only non-cartridge type or removable cartridge type can be used.  
Wireless LAN  
<Only for model with wireless LAN>  
®
Intel PRO / wireless 3945 ABG (802.11 a + b + g) PCI Ex. 1/4  
Data Transfer Rates  
IEEE802.11a: 54/48/36/24/18/12/9/6 Mbps (automatically switched)  
IEEE802.11b: 11/5.5/2/1 Mbps (automatically switched)  
IEEE802.11g: 54/48/36/24/18/12/9/6 Mbps (automatically switched)  
Standards Supported  
Transmission method  
Wireless Channels Used  
IEEE802.11a/IEEE802.11b/IEEE802.11g  
OFDM system, DSSS system  
IEEE802.11a: Channels 36 to 64, 149 to 165  
IEEE802.11b/IEEE802.11g: Channels 1 to 11  
RF Frequency Band  
IEEE802.11a: 5.18-5.32 GHz, 5.745-5.825 GHz  
IEEE802.11b/IEEE802.11g: 2.412-2.462 GHz  
28  
 
             
LIMITED WARRANTY  
For U.S.A.  
PANASONIC PERSONAL COMPUTER AND PERIPHERALS LIMITED WARRANTY  
Panasonic Computer Solutions Company (referred to as “Panasonic”) will repair this product (other than software, which is covered  
by a separate warranty) with new or rebuilt parts, free of charge in the U.S.A. for three (3) years from the date of original purchase in  
the event of a defect in materials or workmanship. This warranty includes the AC adaptor but excludes the batteries and all other  
options and accessories which are covered for a period of one (1) year from the date of purchase.  
This warranty is extended solely to the original purchaser. A purchase receipt or other proof of date of original purchase will be  
required before warranty performance is rendered.  
This warranty only covers failures due to defects in materials or workmanship which occur during normal use. It does not cover dam-  
age which occurs in shipment or failures which are caused by products not supplied by Panasonic, or failures which result from alter-  
ation, accident, misuse, introduction of liquid or other foreign matter into the unit, abuse, neglect, installation, maladjustment of  
consumer controls, improper maintenance, modification or service by anyone other than a Factory Service Center or authorized  
Panasonic Service Dealer, or damage that is attributable to acts of God.  
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CON-  
TROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS . PANASONIC WILL NOT BE RESPONSIBLE  
FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.  
*1  
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems  
when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems  
and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36.  
Limits and Exclusions:  
There are no other express warranties except as listed below.  
PANASONIC SHALL NOT BE LIABLE FOR LOSS OF DATA OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES  
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS  
AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclu-  
sion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations  
or exclusions may not apply to you.  
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If a problem  
with your product develops during or after the warranty period, you may contact our representatives at 1-800-LAPTOP5. If the prob-  
lem is not handled to your satisfaction, then write to the Consumer Affairs Division at the address indicated below.  
SOFTWARE LIMITED WARRANTY  
Panasonic Computer Solutions Company (referred to as “Panasonic”) warrants to you only that the disk(s) or other media on which  
the Programs are furnished will be free from defects in materials and workmanship under normal use for a period of sixty (60) days  
from the date of delivery thereof to you, as evidenced by your purchase receipt.  
This is the only warranty Panasonic makes to you. Panasonic does not warrant that the functions contained in the Programs will meet  
your requirements or that the operation of the Programs will be uninterrupted or error free.  
Panasonic’s entire liability, and your exclusive remedy under this warranty shall be limited to the replacement, in the United States, of  
any defective disk or other media which is returned to Panasonic’s Authorized Service Center, together with a copy of the purchase  
receipt, within the aforesaid warranty period.  
Anything in the foregoing to the contrary notwithstanding, Panasonic shall have no obligation for any defects in the disk(s) or other  
media on which the Programs are furnished resulting from your storage thereof, or for defects that have been caused by operation of  
the disk(s) or other media otherwise than on the Product or in environmental conditions other than those specified by Panasonic by  
alteration, accident, misuse, abuse, neglect, mishandling, misapplication, installation, maladjustment of consumer controls, improper  
maintenance, modification of damage that is attributable to acts of God. In addition, Panasonic shall have no obligation for any  
defects in the disk(s) or other media if you have modified, or attempted to modify any Program.  
DURATION OF IMPLIED WARRANTIES, IF ANY, IS LIMITED TO SIXTY (60) DAYS.  
PANASONIC ASSUMES NO RISK OF AND SHALL NOT IN ANY CASE BE LIABLE FOR ANY DAMAGES, INCLUDING, WITHOUT  
LIMITATION, ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES ARISING FROM BREACH OF WAR-  
RANTY OR CONTRACT, NEGLIGENCE OR ANY OTHER LEGAL THEORY, INCLUDING, WITHOUT LIMITATION LOSS OF  
GOODWILL, PROFITS OR REVENUE, LOSS OF USE OF THE PROGRAMS OR PRODUCTS OR ANY ASSOCIATED EQUIP-  
MENT, COST OF CAPITAL, COST OF ANY SUBSTITUTE EQUIPMENT, FACILITIES, SERVICES, DOWNTIME COSTS, OR  
CLAIMS OF ANY PARTY DEALING WITH YOU FOR SUCH DAMAGES.  
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied  
warranty lasts, so the above limitations or exclusions may not apply to you.  
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
This Limited Warranty will be governed by the laws the State of New York, without regard to its conflict-of-laws rules.  
*
*
*
To obtain service or technical assistance within the continental U.S.A. and Alaska.  
DIAL TOLL FREE: 1-800-LAPTOP5  
Correspondence requesting product information should be sent to:  
Panasonic Computer Solutions Company  
50 Meadowlands Parkway, Panazip 2F-5, Secaucus, NJ 07094  
29  
 
   
LIMITED WARRANTY  
For Canada  
PANASONIC COMPUTER AND PERIPHERALS LIMITED WARRANTY  
Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, this computer product (excluding software  
media), when purchased from PCI or from a PCI authorized reseller, to be free from defects in materials and workmanship under nor-  
mal use, subject to the terms set forth below, during the period of warranty coverage specified.  
Scope of Coverage  
Period of Coverage  
Type of Failure Coverage  
Whole Product (except Batteries), AC adaptor and CD- Three (3) Years from Date of Origi- Defective Materials or Workman-  
ROM (if factory installed)  
nal End User Customer Purchase  
ship  
Batteries, CD-ROM (unless factory installed), Port  
One (1) Year from Date of Original Defective Materials or Workman-  
Replicator, Extra Memory Modules and all other Periph- End User Customer Purchase  
erals, Options and Accessories  
ship  
Remedy – In the event of a warranty claim, contact PCI’s representatives within the applicable warranty period, identifying the nature  
of the defect claimed, at 1-800-668-8386 between 9:00 A.M. and 5:00 P.M., Eastern Time Zone, Mon. – Fri. (excluding holidays) for  
instructions on how to obtain service. A purchase receipt or other proof of date of original purchase is required before warranty ser-  
vice is performed. Defective parts covered by this Limited Warranty will be repaired or replaced with new or comparable rebuilt parts  
on an exchange basis. Warranty replacement or repair is subject to the terms of this Limited Warranty for the balance of the original  
period of warranty coverage.  
No Coverage – This Limited Warranty does not cover products purchased outside Canada. Neither does it cover damage to, failure  
of, or defects in a product or accessory through mishandling, improper installation, abnormal use, misuse, neglect, accident, intro-  
duction of liquid or other foreign matter into the product, alteration or servicing by anyone not authorized by PCI, or act of God.  
THIS PRODUCT IS NOT INTENDED FOR USE AS, OR AS PART OF, NUCLEAR EQUIPMENT/SYSTEMS, AIR TRAFFIC CON-  
TROL EQUIPMENT/SYSTEMS, OR AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS . PANASONIC WILL NOT BE RESPONSIBLE  
FOR ANY LIABILITY RESULTING FROM THE USE OF THIS PRODUCT ARISING OUT OF THE FOREGOING USES.  
*2  
AIRCRAFT COCKPIT EQUIPMENT/SYSTEMS include Class2 Electrical Flight Bag (EFB) Systems and Class1 EFB Systems  
when used during critical phases of flight (e.g., during take-off and landing) and/or mounted on to the aircraft. Class1 EFB Systems  
and 2 EFB Systems are defined by FAA: AC (Advisory Circular) 120-76A or JAA: JAA TGL (Temporary Guidance Leaflets) No.36.  
IF YOU SHIP THE PRODUCT FOR WARRANTY SERVICE  
Carefully pack the product, preferably in the original carton. Include details of defect claimed and proof of date of original purchase.  
No liability is assumed for loss or damage to the product while in transit, if you chose your own transportation carrier.  
SOFTWARE MEDIA LIMITED WARRANTY  
Coverage – Panasonic Canada Inc. (“PCI”) warrants to you, the first end user customer, that the disk(s) or other media on which  
software program(s) is/are supplied will be free from defects in materials and workmanship under normal use in Canada for a period  
of sixty (60) days from date of receipt as evidenced by your purchase receipt for your Panasonic Computer product.  
THIS IS THE ONLY WARRANTY THAT PCI MAKES RESPECTING THE SOFTWARE MEDIA. PCI does not warrant the software.  
Please refer to the software licensor’s written warranty (accompanying the copy of the software) for any software warranty claim.  
Claim Procedure – In the event of a defect in material or workmanship in the media during the sixty (60) day warranty period, and  
you return it, transportation costs prepaid, to Panasonic Canada Inc., Computer Products Marketing, at the above address, within the  
warranty period, together with a copy of your purchase receipt, and an explanation of the suspected defect, PCI will replace in Can-  
ada the defective disk(s) or other media.  
Remedy – PCI’s entire liability, and your only remedy for any breach of this software media warranty is limited to replacement of the  
media only. It does not cover any other damages, including, but not limited to, loss of use or profit loss, or special, indirect or conse-  
quential damages, or other claims, whether or not of similar character.  
No Coverage – This limited warranty does not apply if the disk(s) or other media has been used in other than a Panasonic product,  
or in environmental conditions other than those specified by PCI or the manufacturer, or if subjected to misuse, neglect, mishandling,  
modification or attempted modification of the program, or if damaged by accident or act of God. PCI is not responsible for damage to  
or loss of any program, data or removable storage media.  
GENERAL  
NO OTHER WARRANTIES – PCI DISCLAIMS ALL OTHER WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH  
RESPECT TO THE SOFTWARE, SOFTWARE MEDIA, COMPUTER PRODUCT, OPTIONS AND ACCESSORIES.  
NO LIABILITY FOR CONSEQUENTIAL DAMAGES – IN NO EVENT SHALL PCI BE LIABLE FOR ANY SPECIAL, INDIRECT OR  
CONSEQUENTIAL DAMAGES ARISING FROM ANY BREACH OF THE LIMITED WARRANTIES SET OUT IN THIS DOCUMENT,  
OR FROM THE USE OF THE COMPUTER PRODUCT, INCLUDING, WITHOUT LIMITATION, LOSS OF DATA, BUSINESS,  
PROFIT OR GOODWILL.  
IN ANY EVENT, PCI’S MAXIMUM LIABILITY FOR ANY BREACH SHALL NOT EXCEED THE AMOUNT ACTUALLY PAID BY YOU  
FOR THE COMPUTER PRODUCT.  
NO ACTION, REGARDLESS OF ITS BASIS, MAY BE BEGUN AGAINST PCI MORE THAN TWO (2) YEARS AFTER THE CAUSE  
OF ACTION AROSE.  
Statutory Warranties – Some jurisdictions do not allow these limitations or exclusions, so they may not apply to you.  
30  
 
 
MEMO  
31  
 
®
As an ENERGY STAR Partner, Matsushita Electric Industrial Co., Ltd. has  
®
determined that this product meets the ENERGY STAR guidelines for energy efficiency.  
®
Outline of the International ENERGY STAR Office Equipment Program  
®
The international ENERGY STAR Office Equipment Program is an international program that promotes energy  
saving through the use of computers and other office equipment. The program backs the development and dissem-  
ination of products with functions that effectively reduce energy consumption. It is an open system in which busi-  
ness proprietors can participate voluntarily. The targeted products are office equipment such as computers,  
displays, printers, facsimiles, and copiers. Their standards and logos are uniform among participating nations.  
®
For information about ENERGY STAR , refer to the following web site:  
Panasonic Computer Solutions Company  
50 Meadowlands Parkway, Panazip 2F-5,  
Secaucus, NJ 07094  
Panasonic Canada Inc.  
5770 Ambler Drive Mississauga,  
Ontario L4W 2T3  
TA0106-4107  
DFQX5589WAT  
© 2007 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.  
 

NEC Computer Monitor FE700 User Manual
New Buck Corporation Gas Heater 1127B User Manual
Nikon Marine Battery EN EL9 User Manual
Nilfisk Advance America Vacuum Cleaner GD10 User Manual
NuTone Air Conditioner 9965 User Manual
Palsonic CD Player CD6990DM3UC User Manual
Panasonic Car Stereo System CQ VX777EW User Manual
Panasonic Fan FV 05 08 11VFL2 User Manual
Parasound TV Converter Box D AC 1000 User Manual
Parkside Cordless Drill X1 8V User Manual