NETGEAR Modem WPN802 User Manual

e. Turn on your computer, and connect the power adapter to the WPN802. Then  
check the lights on the front:  
Deploy the WPN802  
)NSTALLATION 'UIDE  
1. Disconnect the WPN802 from the computer and place it  
where you will deploy it.  
Power: The power light should be lit. If the power light is not lit,  
check the connections and check to see if the power outlet is controlled by a  
wall switch that is turned off.  
NETGEAR WPN802 RangeMax™ Wireless Access Point  
The best location is elevated, such as wall mounted or on  
the top of a cubicle, at the center of your wireless coverage  
area, and within line of sight of all the mobile devices. If the  
WPN802 is on a metal surface it must be positioned  
vertically.  
Start Here  
Test: The test light blinks when the WPN802 is first turned on.  
Please refer to the Reference Manual on your Resource CD for instructions on advanced  
configuration options.  
WLAN: The wireless light should be lit.  
Estimated Completion Time: 30 minutes.  
Ethernet: The Ethernet (LAN) light should be lit (amber for a 10  
Mbps connection and green for a 100 Mbps connection). If not, make sure  
the Ethernet cable is securely attached at both ends.  
Tip: Before mounting the WPN802 in a high location, first set up and test the WPN802 to  
verify wireless network connectivity.  
2. Connect an Ethernet cable from your WPN802 Access  
Point to a LAN port on your router, switch, or hub.  
First, Set Up the WPN802  
2. CONFIGURE LAN AND WIRELESS ACCESS  
a. Configure the WPN802 Ethernet port for LAN access.  
1. CONNECT THE WIRELESS ACCESS POINT TO YOUR COMPUTER  
Connect to the WPN802 by opening your browser and  
WPN802  
,QWHUQHW  
a. Unpack the box and verify the contents.  
b. Prepare a computer with Internet access and an Ethernet adapter. If this computer  
is already part of your network, record its TCP/IP configuration settings. Config-  
ure the computer with a static IP address of 192.168.0.210 and 255.255.255.0 as  
the Subnet Mask.  
Router  
When prompted, enter admin for the user name and password for the  
password, both in lower case letters.  
c. Connect an Ethernet cable from  
the WPN802 to the PC.  
3. Connect the power adapter to the wireless access point and plug the power adapter in  
to a power outlet. The Power, WLAN and Ethernet lights should light up.  
Click the Basic Settings link and configure the IP Settings for your network.  
d. Securely insert the other end of  
the cable into the WPN802  
Ethernet port.  
b. Configure the wireless interface for wireless access. See the online help or the  
Reference Manual for full instructions.  
Now, Verify Wireless Connectivity  
c. Test wireless connectivity using a computer with a wireless adapter configured  
according to the wireless settings you just set in the WPN802 to establish a  
wireless connection to the WPN802.  
Using a computer with an 802.11g or 802.11b wireless adapter, verify connectivity by  
using a browser such as Netscape® or Internet Explorer to connect to the Internet, or  
check for file and printer access on your network.  
Now that you have finished the setup steps, you are ready to deploy the WPN802 in  
your network. If needed, you can now reconfigure the PC you used in step 1 back to  
its original TCP/IP settings.  
Note: If you cannot connect, see to Troubleshooting Tips in this guide or the Reference  
Manual on the Resource CD for the Wireless Access Point.  
 

MTX Audio Computer Monitor 251B User Manual
MTX Audio Speaker T8154A User Manual
Multiquip Automobile Parts DCA150USJ2 User Manual
Nikon Binoculars Monarch Titanium User Manual
Nikon Camera Lens 2163 User Manual
Nikon Microscope Magnifier SMZ U User Manual
Onkyo Stereo System HT S780 User Manual
Panasonic Cell Phone A100 User Manual
Panasonic Electric Shaver EH2511 User Manual
Panasonic Telephone KX NT700 User Manual