Metra Electronics Automobile Accessories 99 3306 User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-3306  
APPLICATIONS  
Chevrolet Aveo sedan 2007-2010  
Pontiac G3 2007-2009  
99-3306  
KIT FEATURES  
• DIN Mount Radio Provision with Pocket  
• ISO Mount Radio Provision with Pocket  
• Double DIN Mount Radio Provision  
• Stacked ISO Units Provision  
KIT COMPONENTS  
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets  
• E) Double DIN Trim Plate • F) Pocket  
C
D
B
A
WIRING AND ANTENNA CONNECTIONS: (Sold Separately)  
Wiring Harness:  
• 70-2105 - GM harness 2006-up  
• 70-8405 - GM/Suzuki/Daewoo harness 1999-up  
Antenna Adapter:  
• 40-CR10 - CHRYSLER/GM antenna adapter 2002-up  
E
F
TOOLS REQUIRED:  
Small Flat Blade Screwdriver/ Panel Removal Tool  
• Phillips Screwdriver • Socket Set  
1-800-221-0932  
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
 
99-3306 DASH DISASSEMBLY  
CHEVROLET AVEO 2007-2010  
PONTIAC G3 2007-2009  
A
Disconnect the negative battery ter-  
minal to prevent an accidental short  
circuit.  
1
2
3
Unclip and remove trim panel around  
radio. (Figure A)  
SOUND  
AST  
SCAN  
1
3
6
2
4
5
Remove (4) 9/32” screws securing  
the radio. Unplug and remove radio.  
(Figure B)  
Continue to kit assembly.  
B
SOUND  
AST  
SCAN  
1
3
6
2
4
5
2
1
3
4
1
 
99-3306 KIT ASSEMBLY  
DIN MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
Slide the DIN cage into the Radio  
1
Housing and secure by bending the  
metal locking outward. (Figure A)  
2
3
Slide the aftermarket radio into the DIN  
cage until it snaps into place. (Figure B)  
Snap the pocket into the radio housing.  
(Figure C)  
Continue to final assembly.  
B
C
2
 
99-3306 KIT ASSEMBLY  
ISO MOUNT RADIO PROVISION WITH POCKET  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
1
Mount the ISO Brackets to the radio  
using the screws supplied with the  
radio. (Figure A)  
2
3
4
Slide the radio into the radio opening  
until it snaps into place. (Figure B)  
Snap the ISO Trim Plate onto the front  
of the Radio Housing. (Figure B)  
Snap the pocket into the radio hous-  
ing. (Figure C)  
B
Continue to final assembly.  
C
3
 
99-3306 KIT ASSEMBLY  
DOUBLE DIN MOUNT RADIO PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
1
2
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the radio housing.  
(Figure B)  
3
4
Slide the Double DIN radio into the  
bracket/radio housing assembly and  
secure the radio to the assembly using  
the screws supplied with the radio.  
(Figure C)  
B
Snap the Double DIN trim-plate onto  
the front of the housing/radio assem-  
bly. (Figure C)  
Continue to final assembly.  
C
4
 
99-3306 KIT ASSEMBLY  
STACKED ISO UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
A
1
2
Cut and remove the center bar from  
the radio housing. (Figure A)  
Snap the Double DIN brackets to the  
inside edge of the radio housing.  
(Figure B)  
3
4
Slide the stacked ISO units into the  
bracket/radio housing assembly and  
secure the units to the assembly using  
the screws supplied with the units.  
(Figure C)  
B
Snap the Double DIN trim-plate onto  
the front of the housing/radio assem-  
bly. (Figure D)  
Continue to final assembly.  
D
C
5
 
99-3306 FINAL ASSEMBLY  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individ-  
ually tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the  
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and  
individually tape off ends of any unused wires to prevent electrical short circuit.  
METRA / EIA WIRING CODE  
12V Ignition / Acc. . . . . . . . . . Red  
Right Front (+) . . . . . . . . . . . . Gray  
12V Batt / Memory. . . . . . . . . Yellow  
Ground. . . . . . . . . . . . . . . . . . Black*  
Power Antenna. . . . . . . . . . . . Blue  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Amp Ground. . . . . . . . . . . . . . Black / White  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
Left Front (+) . . . . . . . . . . . . . White  
Left Front (-). . . . . . . . . . . . . . White / Black  
Right Rear (+) . . . . . . . . . . . . Violet  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Left Rear (+) . . . . . . . . . . . . . Green  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
1-800-221-0932  
REV. 04/21/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-3306  
6
 

Lochinvar Gas Heater CLR 065 50 thru 090 100 User Manual
Lochinvar Water Heater 6 120 User Manual
Lumens Technology Webcam VC G50 User Manual
Magnavox Clock Radio AJ3282 User Manual
Manitowoc Ice Ice Maker K00117 User Manual
Marshall electronic Flat Panel Television V R102DP HDSDI User Manual
Martin Fireplaces Stove VFCS20SNV User Manual
Metra Electronics Car Stereo System 99 7009 User Manual
Metz Flat Panel Television Slim TV User Manual
Middleby Marshall Oven PS770G GAS User Manual