Linear Satellite Radio DXS 62 EC User Manual

PRODUCT DESCRIPTION  
FEATURES  
The Models DXS-62 and DXS-63 are battery powered, miniature,  
water-resistant*, supervised transmitters designed for use in emergency  
applications with Linear’s DX and DXS Format receivers. Each is supplied  
with a wristband, a pocket clip, and a Nylon pendant necklace. Pressing  
buttons on either transmitter sends a digital coded wireless signal to its  
companion receiver. To insure sending a complete signal,  
press the transmitter button(s) for a minimum of two  
seconds.  
Each DXS transmitter is factory set to a unique code, so no field coding  
is required. The one-button DXS-62 sends a signal when its button is  
pressed. The two-button DXS-63 transmitter sends a signal when both  
buttons are pressed together. These transmitters can send a signal for  
up to 30seconds per activation.The red signal indicator on the transmitter  
lights and a built-in sounder beeps when the unit is activated.  
If status transmissions are enabled, they will be sent every two hours.  
Some receivers are able to use these signals, others are not.  
Every two hours the transmitter tests for a low battery. This test takes  
place even if status transmissions have not been enabled. If the battery  
tests low, the transmitter sounder will beep and a low battery signal will  
be sent.  
DXS-62/EC  
DXS-63/EC  
ACTIVATION  
BUTTON  
BY  
SIGNAL  
INDICATOR  
ACTIVATION  
BUTTONS  
(PRESS BOTH)  
DXS-62  
DXS-63  
NYLON  
NECKLACE  
SUPERVISED  
EMERGENCY  
TRANSMITTERS  
Operation Instructions  
Receivers must be programmed to the transmitter’s code before system  
testing and operation. Refer to the receiver’s instructions for details on  
operation and programming.  
Each transmitter is sealed to provide water-resistance. The unit’s battery  
is not replaceable. The transmitter should be discarded at the end of its  
battery life.  
POCKET  
CLIP  
WRIST  
STRAP  
(760) 438-7000 • FAX (760) 438-7043  
PENDANT HOLDER  
* NOTE:Water resistance not tested by UL  
WRISTBAND INSTALLATION  
PENDANT HOLDER INSTALLATION  
POCKET CLIP INSTALLATION  
TO INSTALL PENDANT HOLDER, SLIDE HOLDER  
INTO SLOTS ON ENDS OF TRANSMITTER  
TO INSTALL WRISTBAND, SLIDE STRAPS  
INTO SLOTS ON ENDS OF TRANSMITTER  
INSTALL THE PENDANT HOLDER  
THEN CUT AND REMOVE THE NECKLACE  
SNAP THE POCKET CLIP  
INTO THE PENDANT HOLDER  
NOTE: THE END OF STRAP WITH VELCRO ATTACHES  
TO THE END CLOSEST TO THE SIGNAL INDICATOR  
NOTE: NECKLACE SIDE OF PENDANT HOLDER  
FITS CLOSEST TO THE SIGNAL INDICATOR  
STATUS OPTION & PROGRAMMING  
SYSTEM TESTING  
INTERNATIONAL WARRANTY  
This Linear product is warranted against defects in material and workmanship for twelve (12)  
months. The Warranty Expiration Date is labeled on the product. This warranty extends only  
to wholesale customers who buy direct from Linear or through Linear’s normal distribution  
channels. Linear does not warrant this product to consumers. Consumers should inquire  
from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations  
or liabilities on the part of Linear Corporation for consequential damages arising out  
of or in connection with use or performance of this product or other indirect damages  
with respect to loss of property, revenue, or profit, or cost of removal, installation, or  
reinstallation. All implied warranties, including implied warranties for merchantability and implied  
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product.  
This Linear Corporation Warranty is in lieu of all other warranties express or implied.  
For warranty service on Linear equipment return product, at sender’s expense to:  
IMPORTANT! TEST SYSTEM WEEKLY  
IF THE FOUR HOUR STATUS TIMER IS REQUIRED FOR  
SUPERVISION, PERMANENTLY ENABLE THE TIMER BY  
PRESSING THE TRANSMITTER BUTTON FIVE TIMES IN  
SUCCESSION (USE THE LEFT BUTTON ON DXS-63). THE DXS-62  
WILL BEEP AFTER EACH BUTTON PRESS, THE DXS-63 WILL  
NOT. FIVE BEEPS WILL SOUND WHEN THE TIMER IS ENABLED.  
The manufacturer strongly recommends that you test  
security equipment frequently. Over a period of time, no  
electronic products are better than the inspection and  
maintenence they receive. Therefore, from the time of  
installation, it is absolutely necessary to test the system  
at least once a week.  
Linear Hong Kong 19/F Hounor Industrial Centre,  
Attention: Repairs Department  
6
Sun Yip Street Chai Wan, Hong Kong  
PLACE THE RECEIVER IN A "TEST"  
MODE AND ACTIVATE THE  
TRANSMITTTER. VERIFY THAT THE  
SIGNAL IS RECEIVED AND THAT THE  
SYSTEM REPORTS AS REQUIRED.  
REPAIRS POLICY  
/
/
/
Charges will be made for equipment that is not in warranty, shows customer abuse, or is  
damaged by the effects of lightning, water, fire, or other abnormal happenings.  
Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured  
equipment at Linear’s discretion.  
The customer is always responsible for shipping and handling charges to the repairs facility.  
Linear will pay return shipping and handling charges on “in warranty” products shipped back  
to the customer. The customer will be billed for the return shipping and handling charges on “out  
of warranty” products.  
BEEP... BEEP...  
BEEP  
BEEP... BEEP...  
/
/
There will be a 50% expedite fee for any express requests.  
The International Sales Manager must be notified prior to the return of product to Linear. All  
international returns must have an International Repair Authorization number (IRA#). The number  
must be marked on all packages. Failure to do so will cause delays in processing.  
IMPORTANT !!!  
/
/
/
Linear radio controls provide a reliable communications link and fill an important need in portable  
wireless signaling. However, there are some limitations which must be observed.  
The radios are required to comply with local rules and regulations as radio devices. As such, they  
have limited transmitter power and therefore limited range.  
A receiver cannot respond to more than one transmitted signal at a time and may be blocked  
by radio signals that occur on or near their operating frequencies, regardless of code settings.  
Changes or modifications to the device may void regulatory compliance.  
Infrequently used radio links should be tested regularly to protect against undetected interference  
or fault.  
PROGRAM THE TRANSMITTER INTO THE RECEIVER BY  
PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND  
/
/
A
SIGNAL TO THE RECEIVER FROM THE TRANSMITTER.  
REFER TO THE RECEIVER'S PROGRAMMING INSTRUCTIONS  
FOR DETAILS.  
/
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale  
distributor or dealer, and these facts should be communicated to the ultimate users.  
Copyright © 2003 Linear Corporation  
215558 D  
 

Lennox International Inc Furnace G40DFX SERIES User Manual
LG Electronics Refrigerator LFC28768SB User Manual
Lincoln Electric Welder SVM176 A User Manual
LST Home Security System SZ58 3 User Manual
Maytag Washer MAV 3 User Manual
Melissa Microwave Oven 753 084 User Manual
Melissa Vacuum Cleaner 240 116 User Manual
Mercury Automobile 2007 Montego User Manual
Metra Electronics Cooktop 99 7863 User Manual
MicroNet Technology Network Router SP3367A User Manual