Life Fitness Home Gym 93Xi User Manual

93Xi, 90X Total Body Tr ainer s  
As s e mb l y In s t r u c t io n s  
 
IMPORTANT SAFETY INSTRUCTIONS!  
DO NOT LOCATE THE CROSS-TRAINER OUTDOORS, NEAR SWIMMING POOLS, OR IN AREAS OF HIGH  
HUMIDITY.  
DO NOT OPERATE YOUR CROSS-TRAINER IF IT HAS BEEN DROPPED, DAMAGED, OR EVEN PARTIALLY  
IMMERSED IN WATER. IF THIS OCCURS, CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT  
THE NUMBER IN THE OPERATION MANUAL.  
DO NOT LOCATE THE CROSS-TRAINER ANY CLOSER THAN 30 INCHES (76 CM ) TO A TELEVISION  
SET.  
DO NOT LOCATE ADDITIONAL CROSS-TRAINERS ANY CLOSER THAN 42 INCHES (107 CM) FROM  
CENTER TO CENTER TO AVOID INTERFERENCE (CROSS TALK) BETWEEN HEART RATE MONITORS.  
DO KEEP THE AREA AROUND YOUR CROSS-TRAINER CLEAR OF ANY OBSTRUCTIONS, INCLUDING  
WALLS AND FURNITURE. ENSURE THAT THERE IS AT LEAST A 12 INCH (30CM) CLEARANCE IN FRONT  
OF THE CROSS-TRAINER.  
DO VERIFY THE CONTENTS OF THE DELIVERY CARTON AGAINST THE ACCOMPANYING PARTS LIST  
PRIOR TO SETTING THE CARTONS AND SHIPPING MATERIAL ASIDE. IF ANY PARTS ARE MISSING,  
CONTACT LIFE FITNESS CUSTOMER SUPPORT SERVICES AT THE NUMBER LISTED IN THE OPERATION  
MANUAL. SAVE THE SHIPPING CARTONS IN CASE OF RETURN.  
DO READ THE ENTIRE OPERATION MANUAL PRIOR TO ATTEMPTING TO OPERATE THIS MACHINE AS  
THIS IS ESSENTIAL FOR PROPER USE.  
CONSIGNES DE SECURITE IMPORTANTES!  
NE PLACEZ PAS L'APPAREIL À L'EXTÉRIEUR, PRÈS D'UNE PISCINE OU DANS UN ENDROIT TRÈS  
HUMIDE  
NE FAITES PAS FONCTIONNER L'APPAREIL S'IL EST TOMBÉ, S'IL A ÉTÉ ENDOMMAGÉ OU S'IL A ÉTÉ  
PARTIELLEMENT PLONGÉ DANS L'EAU. SI CELA S'EST PRODUIT, CONTACTEZ LE SERVICE APRÈS-VENTE  
DE LIFE FITNESS AU NUMÉRO FOURNI DANS LE MANUEL D'UTILISATION  
NE PLACEZ PAS L'APPAREIL À MOINS DE 76 CM D'UN POSTE DE TÉLÉVISION  
NE PLACEZ PAS D'AUTRES APPAREILS DU MÊME TYPE À PROXIMITÉ. UN ESPACE D'AU MOINS 107 CM  
DOIT ÊTRE OBSERVÉ ENTRE LES PARTIES CENTRALES DE DEUX APPAREILS AFIN D'ÉVITER LES  
INTERFÉRENCES ENTRE LES CONTRÔLEURS DE RYTHME CARDIAQUE.  
MAINTENEZ LA ZONE AUTOUR DE L'APPAREIL LIBRE DE TOUTE OBSTRUCTION, Y COMPRIS MURS ET  
MEUBLES. VEILLEZ À LAISSER UN DÉGAGEMENT D'AU MOINS 30 CM DEVANT L'APPAREIL  
VÉRIFIEZ SI L'EMBALLAGE CONTIENT TOUTES LES PIÈCES DE LA LISTE JOINTE AVANT DE LE METTRE  
DE CÔTÉ. SI DES PIÈCES SONT ABSENTES, CONTACTEZ LE SERVICE APRÈS-VENTE DE LIFE FITNESS  
AU NUMÉRO INDIQUÉ DANS LE MANUEL D'UTILISATION. CONSERVEZ L'EMBALLAGE AU CAS OÙ VOUS  
DEVRIEZ RENVOYER L'APPAREIL.  
LISEZ LE MANUEL DE L'UTILISATEUR TOUT ENTIER AVANT D'ESSAYER DE FAIRE FONCTIONNER CET  
APPAREIL. CECI EST INDISPENSABLE À SON UTILISATION CORRECTE.  
 
TOOLS REQUIRED FOR ASSEMBLY...  
Magnetic #2 Bit Phillips Screwdriver, T-45 Hex Key Wrench, 16mm Open End Wrench  
PARTS DESCRIPTION  
1
3
Torx Socket Head Screw  
M8 – 1.25 x 19  
0017-00101-1791  
Phillips Pan Head Screw  
M4.2 – 0.70 x 10  
Qty: 12  
2
Phillips Pan Head Screw  
M4 – 0.70 x 19  
0017-00101-1796  
Qty: 14  
Qty: 1  
Qty: 2  
4
Console Assembly  
0017-00101-1846  
5
Front Rocker Cover  
OK62-01009-0000  
Console Support Assembly  
AK62-00123-0000  
Front Pivot Arm Cover  
OK62-01012-0000  
Left User Arm Assembly  
AK62-00091-0000  
Left Bullhorn Cover  
OK62-01008-0001  
Accessory Tray  
OK62-01022-0000  
Base Frame Cap  
OK62-01004-0000  
Cap: Console Support  
OK62-01030-0000  
Qty: 2  
Qty: 1  
Qty: 2  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 1  
6
Left Back Rocker Cover  
OK62-01011-0000  
Console Support Cover  
OK62-01023-0000  
Rear Pivot Arm Cover  
OK62-01013-0000  
Right User Arm Assembly  
AK62-00090-0000  
Right Bullhorn Cover  
OK62-01007-0001  
Right Back Rocker Cover  
OK62-01010-0000  
Foot Cover  
Qty: 1  
Qty: 1  
Qty: 2  
Qty: 1  
Qty: 1  
Qty: 1  
Qty: 4  
Qty: 2  
7
8
9
10  
12  
16  
18  
20  
22  
11  
15  
17  
19  
21  
OK62-01003-0000  
Phillips Pan Head Screw  
M4 – 0.70 x 44  
0017-00101-1854  
1
3
2
22  
1”  
2”  
3”  
4”  
5”  
This product is preconfigured to accept the addition of the Life Fitness Entertainment System. A POWER CABLE and  
COAXIAL CABLE have been pre-installed. Please read both the product assembly instructions and Entertainment Ready  
assembly instructions (included with the Life Fitness Entertainment System) prior to assembly.  
Route the POWER CABLE and COAXIAL CABLE alongside the MAIN WIRE HARNESS where applicable.  
 
IMPORTANT!  
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE PEDAL LEVERS. ALL NECESSARY COMPONENTS NEEDED  
TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.  
IMPORTANT!  
NE JETEZ PAS LE KIT PLACÉ SUR LE DESSUS DES LEVIERS DE PÉDALE. IL CONTIENT TOUS LES ÉLÉMENTS  
NÉCESSAIRES POUR L'INSTALLATION.  
1. Locate the LEFT HANDLEBAR (11). Position the HANDLEBAR near the top  
of the LEFT PIVOT ARM (A).  
Align the mounting holes of the LEFT HANDLEBAR with the mounting holes  
at the top of the LEFT PIVOT ARM. Secure them together using three  
SCREWS (1).  
11  
9
2. Locate one LEFT FRONT ROCKER COVER (5) and the LEFT BACK  
ROCKER COVER (6). Position the LEFT BACK ROCKER COVER over the  
user side of the ROCKER ARM making sure that it seats fully over the  
BULLHORN MOUNTING BRACKET (D). Place the FRONT ROCKER  
COVER over the opposite side of the ROCKER ARM in the same manner.  
Secure the COVERS using two PHILLIPS PAN HEAD SCREWS (2). Tighten  
2
the SCREWS securely. Do not over-tighten the SCREWS.  
1
3. Locate one FRONT PIVOT ARM COVER (9) and one BACK PIVOT ARM  
10  
A
COVER (10). Position the BACK PIVOT ARM COVER over the user side of  
the ROCKER ARM making sure that it interlocks with the ROCKER COVER.  
Place the FRONT PIVOT ARM COVER over the opposite side of the PIVOT  
ARM in the same manner. Secure the COVERS using two PHILLIPS PAN  
HEAD SCREWS (2). Tighten the SCREWS securely. Do not over-tighten the  
SCREWS.  
5
4. Remove the LEFT BULLHORN (B) from the BULLHORN MOUNTING  
BRACKET (D) by removing the two SCREWS (C). The shipping installation is  
upside-down from its final installed location. Rotate the LEFT BULLHORN so  
the hand grip faces upwards and reinstall the LEFT BULLHORN using the two  
previously removed SCREWS.  
D
NOTE: IF THE ENTERTAINMENT OPTION WILL NOT BE USED,  
CAREFULLY GATHER THE COAXIAL CABLE (P) AND POWER CORD  
(Q) AND INSERT THEM INTO THE CONSOLE SUPPORT ASSEMBLY (7)  
5. Repeat steps one through four to install the RIGHT ROCKER COVERS (5 &  
6), PIVOT ARM COVERS (9 & 10), BULLHORN (14) and BULLHORN  
COVER (16).  
A
E
NOTE: THE RIGHT PIVOT ARM COVERS ARE REVERSED FRONT AND  
BACK. THE SCREWS WILL BE INSTALLED FROM THE REAR.  
6
2
6. Unwrap the WIRE HARNESS (F,G,P,Q) leading from the MONOCOLUMN  
(H). Feed the WIRE HARNESSES through the CONSOLE SUPPORT  
ASSEMBLY TUBE (I) located at the top and front of the MONOCOLUMN.  
Locate the CONSOLE SUPPORT ASSEMBLY (7) and position it near the top  
of the MONOCOLUMN. Feed the WIRE HARNESSES through the  
CONSOLE SUPPORT ASSEMBLY as shown. Align the bottom mounting  
holes of the CONSOLE SUPPORT ASSEMBLY with those in the CONSOLE  
SUPPORT ASSEMBLY TUBE. Secure them together using six SCREWS (1).  
Tighten the SCREWS securely.  
B
C
15 22  
P
Q
G
F
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRE HARNESSES (E & F)  
WHEN ROUTING IT THROUGH THE CONSOLE SUPPORT ASSEMBLY  
OR WHEN MOUNTING THE CONSOLE SUPPORT ASSEMBLY TO THE  
CONSOLE SUPPORT ASSEMBLY TUBE.  
2
7
21  
4
7. Locate the ACCESSORY TRAY (17). Slide the ACCESSORY TRAY into the  
top of the MONOCOLUMN (H) as shown. Be sure the ACCESSORY TRAY is  
fully seated.  
17  
1
NOTE: BE CAREFUL NOT TO DAMAGE THE MAIN WIRE HARNESS  
WHEN SLIDING THE ACCESSORY TRAY INTO THE MONOCOLUMN.  
2
Secure the accessory tray to the CONSOLE SUPPORT ASSEMBLY using  
two SCREWS (3). Tighten the SCREWS securely. Do not over-tighten the  
SCREWS.  
1
8
3
I
H
 
8. Locate the DISPLAY CONSOLE (4). Position the CONSOLE near the top of  
the CONSOLE BRACKET. Attach all CONNECTORS (F & G) leading from  
the CONSOLE BRACKET to their corresponding CONNECTORS in the  
back of the DISPLAY CONSOLE. Feed any excess WIRE HARNESS into  
the CONSOLE BRACKET and place the DISPLAY CONSOLE onto the  
CONSOLE BRACKET aligning the mounting holes. Secure the DISPLAY  
CONSOLE using four SCREWS (2). Tighten the SCREWS securely. Do not  
over-tighten the SCREWS.  
P
Q
G
F
2
7
21  
4
9. Locate the CONSOLE SUPPORT COVER (8). Position the CONSOLE  
BRACKET COVER over the underside of the CONSOLE SUPPORT  
ASSEMBLY (7) as shown and secure it using two SCREWS (2). Tighten the  
SCREWS securely. Do not over-tighten the SCREWS.  
17  
1
10. Locate the CONSOLE SUPPORT CAP (21). Snap the CAP into position at  
the top of the CONSOLE SUPPORT COVER.  
2
1
11. Locate the BASE FRAME CAP (19). Remove the two SCREWS (J)  
securing the front of the BASE FRAME COVER (K) to the BASE FRAME  
(L). Position the CAP over the front of the BASE FRAME as shown sliding  
the mounting tabs to the inside of the BASE FRAME COVER. Secure the  
CAP using two SCREWS (J) previously removed. Tighten THE SCREWS  
securely. Do not over-tighten the SCREWS.  
8
3
I
12. Locate the four FOOT COVERS (20). Align the COVERS with the ends of  
the STABILIZER BARS (M). Insert the post on the underside of the FOOT  
COVERS into the mounting holes on the top of each STABILIZER. Press  
the FOOT COVERS firmly into position.  
13. Position the unit into the desired location for use. Properly level the unit  
H
according to the instructions in the Operation Manual.  
J
19  
L
20  
M
K
Physical Dimensions:  
93Xi / 90X  
Length  
Width  
84.75 inches / 215 centimeters  
26.5 inches / 67 centimeters  
64 inches / 162.6 centimeters  
286 pounds / 130 kilograms  
Height  
Weight  
 
 
PRE-OPERATION CHECKLIST  
Ensure that all fasteners are tight.  
Make sure the CROSS-TRAINER is properly leveled and stable.  
(Refer to the Operation Manual)  
Ensure that the Leveler Jam Nuts are tight.  
(Refer to the Operation Manual)  
Read the entire Operation manual before using the Cross-Trainer.  
LISTE DES VÉRIFICATIONS À EFFECTUER AVANT LA MISE EN MARCHE  
Vérifiez si tous les dispositifs de fixation sont serrés  
Vérifiez si l'APPAREIL D'EXERCICE POLYVALENT est de niveau et stable.  
(Référez-vous au manuel d'utilisation.)  
Vérifiez si les contre-écrous des vérins de mise à niveau sont serrés.  
(Référez-vous au manuel d'utilisation.)  
Lisez le manuel d'utilisation dans son intégralité avant d'utiliser l'appareil d'exercice polyvalent..  
Before attempting to operate your Total Body Trainer, it is imperative that you familiarize yourself with the contents of  
the Operation Manual. If your Total Body Trainer does not respond as described in the Operation Manual, contact the  
nearest Life Fitness service center as listed in the Operation Manual.  
Life Fitness Customer Support Services  
(800) 351-3737 or (847) 451-0036  
Prior to your call, please be sure you have located and noted the  
MODEL NUMBER & SERIAL NUMBER.  
The Model & Serial number information of your Life Fitness Total Body Trainer is listed on a label  
located on the rear stabilizer.  
©2006 Life Fitness, a division of Brunswick Corporation. All rights reserved. Life Fitness, Lifepulse, FlexDeck and Smart Stop are  
trademarks of Brunswick Corporation.  
MO51-00K62-A177  
10.06  
 

Krell Industries Stereo Amplifier KSA 150 250 User Manual
KWC Outdoor Shower K27H370000A99 User Manual
LG Electronics Flat Panel Television PM9700 User Manual
Liebert Automobile Alarm RCM8CE User Manual
Lucent Technologies Network Card Ethereal User Manual
Marantz Stereo Receiver SR7200 User Manual
Meade Binoculars CV 6 User Manual
Melissa Popcorn Poppers 643068 User Manual
Meridian America Home Theater Server 562V2 User Manual
MGE UPS Systems Power Supply 1000 VA User Manual