Klipsch Speaker SB 2 User Manual

8900 Keystone Crossing, Suite 1220  
Indianapolis, Indiana 46240  
.
.
1 800 KLIPSCH • www.klipsch.com  
Make sure you return your  
warranty card so that we may  
keep you up-to-date on new  
Klipsch products and promo-  
tions. As always, if you have  
any questions, contact your  
local authorized Klipsch dealer.  
For your records:  
Model  
Serial Number  
Date Purchased  
Dealer Name  
193110  
15M1199  
 
CAUTION:  
RIS K OF ELECTRIC S HOCK!  
DO NOT OP EN!  
CAUTION! To reduce the risk of electric shock and fire, do not remove the cover or back plate of this  
device. There are no user-serviceable parts inside. Refer repairs to a Klipsch authorized service center.  
AVIS: Risque de choc electricque, ne pas ouvrir.  
CAUTION! The international symbol of a lightning bolt inside a triangle is intended to caution you to  
uninsulated “dangerous voltage” within the device’s enclosure. The international symbol of an exclama-  
tion point inside a triangle is intended to alert you to the presence of important operating, maintenance  
and servicing information in the manual accompanying the device.  
CAUTION! To prevent electrical shock, match the wide blade of the plug on the power cord to the wide  
slot on the power outlet and insert fully. ATTENTION: Pour eviter les chocs electriques, introduire la  
lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu'au fond.  
CAUTION! To reduce the risk of electrical shock, do not expose this equipment to rain or moisture.  
1. Read Instructions. All safety and operating instructions should be read before operating the device.  
2. Retain Instructions. The safety and operating instructions should be retained for future reference.  
3. Heed Warnings. All warnings on the device and in the operating instructions should be adhered to.  
4. Follow Instructions. All operating and safety instructions should be followed.  
5. Water and Moisture. The device should never be used in, on or near water due to risk of fatal shock.  
6. Carts and Stands. The device should only be used on carts or stands recommended by the  
manufacturer.  
7. Wall and Ceiling Mounting. The device should be mounted on a wall or ceiling only as recommended  
by the manufacturer.  
8. Ventilation. The device should always be located in such a way that it maintains proper ventilation.  
It should never be placed in a built-in installation or anywhere that may impede the flow of air  
through its heat sink or ventilation openings.  
9. Heat. Never locate the device near heat sources such as a radiator, floor register, stove or other heat  
generating device.  
10. Power Supply. The device should only be connected to a power supply of the type described in the  
operating instructions or as marked on the device.  
11. Polarization. This product is equipped with a polarized line plug that has one blade wider than the  
other. To prevent electrical shock, match the wide blade of the plug with the wide blade slot of the  
receptacle and insert fully.  
12. Power Cord Protection. Power cables should be routed so they are unlikely to be stepped on or  
crushed by items placed on or against them. Pay special attention to where the plug enters a socket  
or fused strip and to where the cord enters the device.  
13. Cleaning. The device should be cleaned in accordance with the manufacturers instructions.  
14. Periods of Non-Use. The device should be unplugged from the wall outlet when it is not in use for  
extended periods.  
 
S S -1 W a ll M ount  
Hole M a r king Tem pla t e  
9
4
/
1 6  
"
Cut a long dot t ed line a nd m a il.  
IF YOU P REFER, YOU CAN REGIS TER ONLINE AT W W W .KLIP S CH.COM  
For multiple speaker purchases, please fill out only one warranty card.  
Name:  
Street Address:  
City/State/Zip:  
Home Phone:  
Work Phone:  
E-mail Address:  
Would you like to receive the latest product updates and news via e-mail? q Yes q No  
Product Purchase  
Model and serial number must be included to honor your warranty card. For multiple speaker  
purchases, please fill out only one warranty card.  
Model  
Model  
Model  
Model  
Model  
Model  
Serial Number  
Serial Number  
Serial Number  
Serial Number  
Serial Number  
Serial Number  
What store did you purchase your Klipsch products from?  
Store Name:  
State:  
How did you hear about Klipsch? q Audio/Home Theater Magazine q Other Magazine q TV  
q Radio q Newspaper q Trade Show q Friend q Retail Dealer q Direct Mail  
Have you purchased Klipsch products before? q Yes q No  
If yes, what products?  
Product Name(s):  
When do you hope to purchase additional loudspeakers? q 6 mos. – 1 yr. q 1–2 yrs.  
How likely are you to consider Klipsch products for your upcoming purchases? q Very likely  
q Somewhat likely q Doubtful  
If doubtful, why? q Dont carry product I’m looking for q Too expensive  
q Klipsch dealer too far away q Other  
Please tell us about you!  
q Married q Single q Student  
q Male q Female  
Age: q 15-17 q 18-24 q 25-35 q 36-45 q 46-55 q 55-64 q 65+  
Annual Household Income: q Under $25,000 q $25-35,000 q $35-50,000  
q $75-100,000 q $100,000+  
 
Klips ch Lim it ed W a r r a nt y  
KLIPSCH, L.L.C. (KLIPSCH”) warrants this product to be free from defects in materials and work-  
manship (subject to the terms set forth below). For a period of five (5) years from the date of purchase,  
KLIPSCH will repair or replace (at KLIPSCHs option) this product or any defective parts (excluding  
electronics and amplifiers) in this product. For products that have electronics or amplifiers, the warranty  
on those parts is for a period of two (2) years from the date of purchase.  
To obtain warranty service, please contact the KLIPSCH authorized dealer from which you purchased  
this product. If your dealer is not equipped to perform the repair of your KLIPSCH product, it can be  
returned, freight paid, to KLIPSCH for repair. Please call KLIPSCH at 1-800-KLIPSCH for instructions.  
You will need to ship this product in either its original packaging or packaging affording an equal  
degree of protection.  
Proof of purchase in the form of a bill of sale or receipted invoice, which is evidence that this product is  
within the warranty period, must be presented to obtain warranty service.  
This Warranty is invalid if (a) the factory applied serial number has been altered or removed from this  
product or (b) this product was not purchased from a KLIPSCH authorized dealer. You may call 1-800-  
KLIPSCH to confirm that you have an unaltered serial number and/or you purchased from a KLIPSCH  
authorized dealer.  
This Warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse,  
negligence, commercial use, or modification of, or to any part of, the product. This Warranty does not  
cover damage due to improper operation, maintenance or installation, or attempted repair by anyone  
other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work. Any  
unauthorized repairs will void this Warranty. This Warranty does not cover products sold AS IS or  
WITH ALL FAULTS.  
REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE  
REMEDY OF THE CONSUMER. KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR  
CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON  
THIS PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY LAW, THIS WARRANTY IS  
EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSO-  
EVER, INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY AND  
FITNESS FOR A PRACTICAL PURPOSE.  
Some states do not allow the exclusion or limitation of incidental or consequential damages or implied  
warranties so the above exclusions may not apply to you. This Warranty gives you specific legal rights,  
and you may have other rights which vary from state to state.  
 
15. Dangerous Entry. Care should be taken that no foreign objects or liquids fall or are spilled inside  
the device.  
16. Damage Requiring Service. The device should be serviced by a Klipsch authorized service center when:  
-The plug or power supply cord has been damaged.  
-Objects have fallen or liquid spilled inside of the device.  
-The device has been exposed to moisture.  
-The device does not appear to be operating properly or exhibits a marked change in performance.  
-The device has been dropped or the cabinet has been damaged.  
17. Service. The user should not attempt to service the device beyond what is described in the operating  
instructions. All other servicing should be referred to qualified personnel. If dealer service is not  
available, contact Klipsch customer service for a return authorization (RA) number before shipping.  
Klipsch Customer Service: 800-554-7724  
All return shipments should be made to:  
Klipsch, L.L.C.  
137 County Road #278  
Hope, AR 71801  
RA#…(return authorization number required)  
 
Dea r Klips ch S yner gy S er ies Owner :  
Congratulations on your purchase of Klipsch Synergy Series loudspeakers! These products represent  
the best new thinking, coupled with the Klipsch tradition of sonic excellence.  
The Synergy Series was developed using the latest in materials and technology to deliver extraordinary  
sound from todays digital sources. Designed as a family, the Klipsch Synergy Series was developed  
to provide optimal performance in either a home theater or music system. For home theater use  
Klipsch engineers have developed voice matched center and rear surround speakers to complement the  
main channel speakers. All Synergy models offer the accuracy, dramatic imaging and high sensitivity  
that characterize the “live” Klipsch sound. By utilizing our new Tractrix® Horn technology, the Synergy  
models offer the type of high quality performance normally found only in professional speakers, ensur-  
ing you a truly enjoyable listening experience.  
If this is your first Klipsch purchase, welcome to the fold; if this is an additional Klipsch purchase, we  
thank you for your loyalty. When it comes to the best in home entertainment, Klipsch is a sound choice.  
Please take the time to fill out the enclosed warranty registration card or, if you prefer, you can register  
dealers in meeting your needs as a valued Klipsch customer. Should you have any questions or need  
more information on Synergy or other Klipsch products, please contact us. We will be happy to assist  
you, and welcome your feedback.  
Thank you for choosing Klipsch loudspeakers.  
Sincerely,  
Fred S. Klipsch  
Chairman & CEO  
W e W a nt Your Klips ch P r oduct t o Look a nd  
S ound a s Good a s W hen it Left t he Fa ct or y.  
P lea s e Check P r om pt ly for Tr a ns it Da m a ge.  
Each Klipsch product is individually tested for sonic quality and inspected for superior appearance  
before it leaves the Hope, Arkansas factory. Your loudspeaker left the factory in perfect condition in  
packaging carefully engineered to protect both the working parts and finish. However, in certain  
extreme circumstances, the products may be damaged in transit.  
To ensure that your loudspeaker is in its original condition, please inspect it immediately. If damage  
is discovered, notify the authorized Klipsch dealer that the unit was purchased from or the trans-  
portation company responsible for safe delivery. In the latter case, make a request for inspection from  
the transportation company and hold the product in its original shipping carton for the inspector.  
After a joint inspection report is made, file a claim with the transportation company.  
 
Com ponent S pecica t ions  
S B-2  
S P -1  
Sensitivity: 94dB @ 1 watt / 1 meter  
Bandwidth: 30Hz–20kHz±3dB  
Sensitivity: 93dB @ 1 watt / 1 meter  
Bandwidth: 54Hz–20kHz±3dB  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2400Hz  
Power Handling: 85 watts maximum continuous  
(340 watts peak)  
Enclosure Type: Bass reflex via wide flare, rear-firing por t  
Drive Components: Two-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn and one  
6.5" (16.51cm) K-1092-SB magnetically shielded  
woofer featuring a polymer housing and IMG cone  
Net Weight: 13 lbs. (5.9kg)  
Nominal Impedance: 8 ohms  
Crossover Frequencies: 2.3kHz and 125Hz  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type, Tweeter and Mid Bass: Sealed  
Enclosure Type, Subwoofer: Bass reflex via wide flare,  
rear-firing port  
Drive Components: Three-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn, one 5.25"  
(13.33cm) K-1076-SV magnetically shielded mid-bass  
woofer featuring a polymer housing and IMG cone and  
one 8"(20.32cm) K-1077-SB magnetically shielded  
woofer featuring a polymer housing  
Subwoofer Amplifier: Class A/B MOSFET–225 watts  
FTC-rated power: 55 watts, 4 ohms, 22-125Hz @ 1%  
THD maximum  
Height: 15" (38.1cm)  
Width: 7.3" (18.5cm)  
Depth: 9.75" (24.7cm)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Woodgrain vinyl veneer  
Auto Power: 2 second ON delay, 15 minute OFF delay  
Inputs: High level speaker terminals via five-way binding  
posts, 1) Line level dedicated LFE input via RCA phono  
jack (non-filtered)  
Outputs: 1) Line level LFE output via RCA phono jacks  
(pass through from LFE input)  
Net Weight: 47 lbs. (21.36kg)  
Height: 37" (93.98cm)  
Width: 9" (22.86cm)  
Depth: 14" (35.56cm)  
S B-3  
Sensitivity: 94dB @ 1 watt / 1 meter  
Bandwidth: 52Hz–20kHz±3dB  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2700Hz  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type: Bass reflex via wide flare, rear-firing port  
Drive Components: Two-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn and one  
8" (20.3cm) K-1093-SB magnetically shielded  
woofer featuring a polymer housing and IMG cone  
Net Weight: 18 lbs. (8.18kg)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Woodgrain vinyl veneer  
Voltage: 110/120VAC 60Hz  
Export version: 230VAC 50/60Hz  
Height: 17" (43.18cm)  
Width: 8.69" (22.06cm)  
Depth: 11.25" (28.57cm)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Woodgrain vinyl veneer  
S C-1  
Sensitivity: 95dB @ 1 watt / 1 meter  
Bandwidth: 60Hz–20kHz±3dB  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2.2kHz  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type: Sealed  
S F-1  
Sensitivity: 94dB @ 1 watt / 1 meter  
Bandwidth: 40Hz–20kHz±3dB  
Drive Components: Two-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn and two  
5.25" (13.3cm) K-1079-SV magnetically shielded  
woofers featuring polymer housings and IMG cones  
Net Weight: 15 lbs. (6.78kg)  
Height: 6.5" (16.5cm)  
Width: 18" (45.72cm)  
Depth: 7.5" (19.1cm)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Black matte vinyl  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2kHz  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type: Bass reflex via wide flare, rear-firing por t  
Drive Components: Two-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn and one  
6.5" (16.51cm) K-1075-SB magnetically shielded  
woofer featuring a polymer housing and IMG cone  
Net Weight: 33 lbs. (15kg)  
Height: 33" (83.82cm)  
Width: 8" (20.32cm)  
S S -1  
Depth: 13.6" (34.54cm)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Woodgrain vinyl veneer  
Sensitivity: 94dB @ 1 watt / 1 meter (equivalent sound energy)  
Bandwidth: 60Hz–20kHz±3dB  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2kHz  
S F-2  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type: Sealed  
Sensitivity: 96dB @ 1 watt / 1 meter  
Bandwidth: 35Hz–20kHz±3dB  
Drive Components: Two-way system using two 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion drivers with 90° x 60° Tractrix Horns and one  
5.25" (13.3cm) K-1076-S woofer featuring a polymer  
housing and IMG cone  
Net Weight: 8.5 lbs. (3.9kg)  
Height: 6.75" (17.15cm)  
Width: 15" (38.1cm)  
Depth: 6" (15.24cm)  
Nominal Impedance: 8 ohms  
Crossover Frequency: 2.8kHz  
Power Handling: 100 watts maximum continuous  
(400 watts peak)  
Enclosure Type: Bass reflex via wide flare, rear-firing port  
Drive Components: Two-way system using one 1" (2.54cm)  
K-101-S neodymium magnet, aluminum dome compres-  
sion driver with a 90° x 60° Tractrix Horn and two  
6.5" (16.51cm) K-1078-SB magnetically shielded  
woofers featuring a polymer housings and IMG cones  
Net Weight: 38 lbs. (17.3kg)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Black or white  
Height: 35" (88.9cm)  
Width: 8" (20.32cm)  
Depth: 13.6" (34.54cm)  
Cabinet: Medium density fiber board construction (MDF)  
Finish: Woodgrain vinyl veneer  
This product complies with the essential requirements of EMC direc-  
tives 89/336/EEC and 73/23/EEC (inclusive of 93/68/EEC) and carries  
the CE mark accordingly.  
 
Wa ll M ount ing  
• Install the four rubber stick-on bumpers (one on each corner of the rear panel of the speaker) to  
provide clearance for the speaker wire between the wall and cabinet. This will also prevent the  
speaker from marring the wall.  
• Cut out the template on the back cover of the owners manual to assist in obtaining proper  
spacing of the two mounting holes. If the template is not available, space the mounting screws  
49/16" apart on a vertical line. Allow at least 11/2" of clearance space above the top screw.  
• Check the vertical orientation of the marked hole locations with a torpedo level before drilling.  
• Use a #10 or #12 (21/2 -3"long) pan head wood screw to mount into the wall stud.  
Check the fit of the screw head in the keyhole fitting before installation as screw head sizes do vary.  
• Drill the proper size pilot holes at the marked positions and install the screws into the wall stud.  
1
Leave the back surface of the screw head protruding about /4-inch from the wall surface. This  
will facilitate hooking the keyhole bracket over the screw head with the rubber feet installed. The  
clearance between the wall and the screw head may need to be adjusted to achieve a proper fit.  
If a stud is not available, use the proper type and weight rating of drywall or masonry anchor  
appropriate for the wall construction. Please consult your dealer, custom installer or a building  
contractor in this situation.  
Do not use the keyhole mounting brackets for ceiling installations!  
How t o Connect t he S yner gy S er ies S pea ker s  
AC P OW ER / S P -1 ONLY  
Since your SP-1 has an internal subwoofer power amplifier, it must be plugged into a nearby AC wall  
outlet. The SP-1 should be unplugged from the AC power with the power switch in the OFF position  
during hook up and installation. To eliminate a tripping hazard, all connections should be unplugged  
from the back panel of the speaker if it is being moved. Avoid extremely long extension cords of small  
gauge since they can impair the performance of the subwoofer amplifier and present a potential fire  
hazard. If the SP-1 will not be used for an extended period of time, unplug the power cord from the  
AC power outlet.  
Note: 230 volt models are not supplied with an AC power cord, but are equipped with an IEC-type  
power cord socket.  
CAUTION!  
Since your Klipsch SP-1 has built-in electronics, do not place it near sources of heat or moisture.  
Take care to route the power cord so that it will not be cut, damaged or pinched.  
S P EAKER W IRE CONNECTIONS  
Switch your electronics OFF when making all connections! When making any type of speaker wire  
connection be sure to observe proper polarity (+ to + and - to -). Most speaker wire is insulated,  
two-conductor, stranded construction and is color-coded or has some distinguishing feature differen-  
tiating the two conductors. Speaker wire connectors on most loudspeakers and amplifiers are also  
color-coded. Typically, RED is positive (+) and BLACK is negative (-), or ground. It does not matter  
which conductor is connected to the positive or negative terminals of your equipment as long as you  
are consistent. Be sure that the connections from all of the amplifier channels to all of the speakers in  
your system are connected in a like manner. If not, the quantity of bass will be reduced and the  
stereo image will be compromised. Be careful not to have excess bare wire or loose strands of wire  
at the connections. This could cause a short between adjacent positive and negative terminals, dam-  
aging your speakers and amplifier. Eighteen gauge (AWG) wire is the minimum size recommended  
for short distances, with larger gauges recommended for longer runs. Consult your Klipsch dealer for  
specific suggestions.  
Connect the SB-2, SB-3, SF-1, SF-2 or SP-1 to the Front” or Main” channel speaker outputs of  
your system’s power amplifier.  
 
Connect the SC-1 to the Center” channel speaker output of your system’s power amplifier.  
Connect the SS-1 to the Rear” or Surround” channel speaker outputs of your system’s power  
amplifier. When connecting surround speakers to the rear channels of a 5.1 channel system, it is  
important that they are hooked up to the appropriate left and right rear channels as the surround  
effects are in stereo.  
LINE LEVEL CONNECTIONS / S P -1 ONLY  
Switch your electronics OFF when making all connections! These connections should be made using  
high quality shielded interconnect cables terminated with RCA phono plugs. These cables should be  
as short as possible and kept away from noise-generating electrical equipment, such as digital elec-  
tronics or electric motors. Consult your Klipsch dealer for specific cable recommendations.  
LFE IN / S P -1 Only (opt iona l)  
The “LFE INinput on the SP-1 is a full range input that requires a low pass filtered signal from  
your surround electronics’ subwoofer or LFE output. Do not connect this input to a full range  
(unfiltered) pre-amp output. It is typically used with the newest 5.1 (six channel) surround sound  
systems. The LFE channel contains a different bass signal than the bass frequencies present in the other  
channels. This information can be up to 10 decibels louder than the main channel bass signals, so  
caution should be exercised when connecting to this output and initially adjusting the SP-1’s BASS  
CONTOUR” control. The LFE IN must not be the only connection to the SP-1. The SPEAKER IN”  
terminals are the primary connection for the SP-1.  
LFE OUT / S P -1 Only (opt iona l)  
This output is provided to feed the LFE signal to the other SP-1 if it is difficult or inconvenient to  
connect it directly to the LFE output on your electronics.  
BAS S M ANAGEM ENT  
Most surround sound electronics are equipped with a bass management system that permits the selec-  
tion of a full- or limited-range (filtered) operation for each speaker. You will normally configure the  
main channels of your surround processor to the “Large” or “Full Range” setting and the center and  
surround channels to the “Small” or “Limited Range” setting. The subwoofer or LFE channel of your  
electronics should have its low pass filter engaged when connecting to the optional LFE IN input on  
the SP-1. Consult your Klipsch dealer for more specifics on the bass management configuration of your  
electronics.  
Note: You can bass filter the bookshelf models if a Klipsch powered subwoofer is used with them. This  
will reduce distortion and increase dynamic range during passages that contain high levels of deep bass  
information. Configure your surround processors main channels for the “Small” setting and connect  
the subwoofer to the line level subwoofer output on your electronics. If speaker level hookups are used  
to connect the subwoofer, set the processors main channels to the “Large” setting and connect the  
SB-2s or SB-3s to the high pass filtered, speaker output terminals on the powered subwoofer.  
CONTROLS / S P -1 ONLY  
Ba s s Cont our  
This control adjusts the volume of the subwoofer relative to the mid- and high-frequency drivers. Use  
this control to compensate for room acoustics and speaker placement. This control only affects the  
level of the powered subwoofer in the SP-1. For initial setup, try the FLATposition (full counter  
clockwise) and then increase as desired.  
P ower  
This switch has conventional ON” and OFF” positions, as well as an AUTO” setting. In the  
AUTO” position, the subwoofer will turn itself on when it receives a signal from your system. If no  
signal is sent for a period of 15 minutes, the sub will turn itself off. A red power light indicates  
a standby mode in which the amplifier will turn on when it senses a signal. Green indicates the sub-  
woofer is on and receiving a signal.  
 
Tr oubles hoot ing  
If one or both SP-1 subwoofers have little or no output:  
— Double check your power (AC) and system connections.  
Make sure that the power switch on the rear control panels of both units is set to the  
“ON” or AUTO” position.  
— Check that the power light on the front of the SP-1 is lit. If not, check the AC fuse. When  
changing the AC main’s power fuse, unplug the power cord first. To access the fuse, use the  
appropriate screwdriver to unscrew the cap on the fuse receptacle. If the fuse is blown (the  
filament inside the glass tube is burned through), replace it with the same type and value as  
is printed on the amplifier panel next to the fuse holder. NEVER INSTALL A LARGER  
FUSE THAN THE VALUE INDICATED ON THE AMPLIFIER PANEL. If the fuse blows  
again when the subwoofer is powered up, return the unit to your authorized Klipsch dealer  
for servicing by qualified personnel. If dealer service is not available, contact Klipsch  
customer service for a Return Authorization number before shipping (REQUIRED).  
Klipsch Customer Service: 800-554-7724  
All return shipments should be made to:  
Klipsch, L.L.C.  
137 County Road #278  
Hope, AR 71801  
RA#…(return authorization number required)  
The SP-1s powered subwoofer amplifier is protected by a thermal sensor. If the unit is run for  
extended periods beyond its designated power rating, the thermal sensor will engage and shut  
down the subwoofer. If this occurs, turn the POWER” switch off, turn down the volume on  
your electronics and wait five minutes before restarting the system.  
If you experience a noticeable hum when the SP-1s subwoofer is connected to your system  
(a system that includes video equipment), disconnect the cable television line (if present). If the  
hum disappears, consult your Klipsch dealer for a ground isolator for the cable line. If this does  
not solve the problem, contact your Klipsch dealer for further advise.  
Regardless of your amplifiers rated capacity, do not operate the system at the full output (highest  
volume): Amplifiers can create extremely high levels of distortion when operated at full output  
and can damage your loudspeakers. Most amplifiers are at full power when the volume control is  
at or just above the 12 oclock position.  
Position speaker connection wires so that they do not create a trip hazard.  
If you have any questions regarding the installation or connection of your Klipsch Synergy speakers,  
please contact your Klipsch dealer or contact us directly at 800-554-7724.  
Ca r e a nd Clea ning of Your Klips ch  
S yner gy S pea ker s  
Your speakers have a durable matte vinyl finish that should only require dry dusting or cleaning  
with a damp cloth. Avoid the use of abrasive or solvent-based cleaners and harsh detergents.  
 
Klips ch S yner gy S er ies Technology  
The Klipsch Synergy Series is a complete, matched family of high performance loudspeakers that offers  
superior home theater and two-channel performance. This series offers a choice of two bookshelf  
speakers, the SB-2 and SB-3, and three floorstanding main channel speakers—the SF-1 and SF-2 and a  
model with a built-in powered subwoofer, the SP-1. The voice-matched companion SC-1 center speaker  
and SS-1 surround speakers complete the family. A smaller version of our newest square Tractrix  
Horn, driven by an aluminum diaphragm tweeter, is paired with high output woofers featuring glass-  
fiber-reinforced cast polymer frames and graphite-stiffened, injection-molded, polypropylene cones. All  
front channel models feature video shielding and a “floating” grille design that gives the speakers a  
handsome, contemporary style with minimal sonic interference. Flush mounted components and nar-  
row front profiles are combined with time-aligned drivers and simple, minimum phase filter networks  
to provide truly extraordinary soundstaging. The rear soundfield, in a full surround system configura-  
tion, is provided by the Klipsch SS-1 Wide Dispersion Surround Technologyspeakers. These speakers  
contain an array of three drivers that flood the back of the listening room with high quality direct and  
reflected sound, providing both pinpoint rear channel imaging and ambient envelopment.  
S pea ker P la cem ent  
S YNERGY M AIN S P EAKERS  
Both speakers should be placed on the same wall facing the listening area. Space the loudspeakers so  
they are between six and 15 feet apart. For best results with the bookshelf models, use a high quality  
rigid stand that places the speakers horn tweeter at ear level when seated. For a higher quality stereo  
image, angle, or toe in, the speakers towards the listener.  
The desired spread between the speakers may be different for a home theater application than it would  
be for a two-channel audio system. Some correlation between the size of the video and sonic image may  
dictate the final placement of the speakers. For best results, bring the main speakers forward of the loca-  
tion of the center speaker so that all three front speakers are equidistant from the central viewing posi-  
tion. Some surround electronics allow you to compensate for this electronically by inputting the dis-  
tance from the viewing seat to each speaker.  
Additional bass output will result if you place the speakers in a corner or near a wall due to the addi-  
tional reflected energy from the walls and floor. This may, however, degrade soundstage quality so these  
two attributes must be balanced depending upon your sonic priorities. Room acoustics vary, so experi-  
ment with specific placement within the listening area. Four stick-on rubber feet are included to attach  
to the speaker bottom for use on shelves or hard surface flooring.  
S YNERGY S C-1 CENTER S P EAKER  
Place the center speaker on top of or just below the video screen, centered. This anchors center  
channel sounds to the on-screen image particularly for off-center viewers. When placing the speaker  
below the television, invert the speaker so that it rests on the angled top portion of its cabinet. This  
will direct the sound up to compensate for a low placement height. The grille may be installed in an  
inverted position so the Klipsch logo is properly oriented. Four stick-on rubber feet are included for  
attachment to the speaker bottom to prevent vibration and scratching of the television cabinet or shelf.  
S YNERGY S S -1 W DS T S URROUND S P EAKER  
One of the principle advantages of Klipsch’s unique Wide Dispersion Surround Technology is greater  
placement flexibility. Due to their full 180° coverage pattern, the SS-1s will perform well in a variety  
of locations. The most common placement for home theater rooms is on the side walls, adjacent to or  
behind the listening area, or on the rear walls near the corners of the room. A height of approximately  
five to seven feet from the floor to the base of the speaker is recommended.  
Your Klipsch surround speaker may be wall mounted by using the supplied keyhole brackets on the  
rear of the cabinet. These two brackets are vertically oriented to attach to a pair of screws secured  
into a wall stud.  
 

Infinity Portable Speaker TSS 500 User Manual
Insignia Tablet Accessory NS=CAHCC01 User Manual
Intel Computer Hardware 48201201 User Manual
JBL Speaker HT PS300 User Manual
JVC CD Player KD G710 User Manual
JVC DVD Player HR XVC1UJ User Manual
Kensington Telephone K62070A User Manual
Kenwood CD Player KRC 666 User Manual
Kenwood Two Way Radio TK 3160 User Manual
Kolcraft Stroller S088 R3 User Manual